Frico panther 6 Original Instructions Manual

Brand: Frico

Model: panther 6

Type: Original Instructions Manual

Panther 6 - 15 kW

Original instructions

.... 22

.... 14

.... 12

.... 10

.... 8

.... 20

.... 18

.... 16

.... 28

.... 26

.... 24

520

450

510

100

ø7

ø14

ø6,5

min 300

7,5°

15°

min 1800

30°

min 300

min 1000

Wall

Ceiling

Bracket

Mixing cabinet (accessory)

[mm]

660 430 365 420 445 445 420

Fig 1.

Fig 2.

Panther 6/15

Type E-nr HxBxD

[mm]

RTI2 85 811 44 155x87x43

KRT2800 85 810 44 165x60x57

PP15 87 112 28 160x120x96

PTA01 87 112 31 215x185x115

PBS01 87 112 32 660x430x365

PHR01 87 112 37

PSA01 87 112 35 215x305x115

PSM01 87 112 38 180x100x70

PLR15 87 112 39 355x355x60

PFF15 87 112 44

PTRP 87 112 00

Controls and accessories

PSA01PTA01

KRT2800

RTI2 PP15

PBS01

CBT

KRT1900

TTF140

Drying room kit PTRP.

Panther 6/15

1211

21 1415

Factory setting

LLL123LLL123

K1 K2

230V3~

K1 K2

230V3~

400V3~

°C

-1 – -4°C

KRT 2800

123123

SE 09 - 15

LLL123LLL123

K1 K2

SE 06

LLL123N

230V3~

ºC

LLL123

1234

400V 3N~

PP15

abcd

12345678910111213141516

12345678910

LLL123

440V 3~

500V 3~

440V

500V

230V

SE06-15

RTI2

230V~

234 5 67LN

L N

230V~

>t°C >t°C

Hi Lo

Sensor

SE 06, -09, -12, -15 400V 3N~ / 230V 3~

Panther 6/15

Panther 20

Panther SE06-15

High speed

Medium speed

Low speed

Panther

10987654 1211321 1413 1615

Panther SE06-15

10987654 1211321 1413 1615

Panther SE06-15

10987654 1211321 1413 1615

PP15

Panther

Panther SE06-15

10987654 12113211413 1615

56432187109

Panther SE06-15

High speed

Medium speed

Low speed

Panther

10987654 1211321 1413 1615

Panther SE06-15

10987654 1211321 1413 1615

Panther SE06-15

10987654 1211321 1413 1615

PP15

Panther

Panther SE06-15

10987654 12113211413 1615

56432187109

2 Note! Remove the two internal fuses 6.3A in the slave unit(s).

Note! Remove the two internal fuses 6.3A in the slave unit(s).

Panther 6/15

Panther SE06-15

312

KRT2800

KRT

2800

PP15

312

10987654 1211

321 1413 1615

10987654 1211

321 1413 1615

87654321

PP15 910

Panther

RTI2

PP15

Panther

Panther SE06-15

NL7654321

10987654 12113211413 1615

109876541211321 1413 1615

64321871095

RTI2

Note! Remove the two internal fuses 6.3A in the slave unit(s).

Panther 6/15

Protection class: IP44.

CE compliant.

Technical speciﬁcations | Fan Heater Panther 6-15 kW 3

Ty p E-nr Effektsteg

[kW]

Luftﬂöde

[m³/h]

Ljudnivå*1

[dB(A)]

∆t*2

[°C]

Spänning

[V]

Ström

[A]

HxBxD

[mm]

Vikt

[kg]

SE06 87 112 50 0/3/6 900/1300 39/47 20/14 400V3N~ 8,7 520x450x510 21

SE09 87 112 51 0/4,5/9 900/1300 39/47 30/21 400V3N~ 13,0 520x450x510 22

SE12 87 112 52 0/6/12 900/1300 39/47 40/28 400V3N~ 1 7, 3 520x450x510 22

SE15 87 112 53 0/7,5/15 900/1300 39/47 50/35 400V3N~ 21,7 520x450x510 22

SE135 87 112 36 0/5/10

0/7/13,5

900/1300 39/47 34/23

45/31

440V3~*3

500V3~

13,4

15,6

520x450x510 23

*1) Conditions: Distance to the unit 3 metres. Directional factor: 2. Equivalent absorption area: 200 m2.

*2) ∆t = temperature rise of passing air at maximum heat output at lowest/highest airﬂow.

*³) Can be connected to 440V3~ and 500V3~.

Panther 6/15

GB Panther 6/15

Assembly and operating instructions

General Instructions

Read these instructions carefully before instal-

lation and use. Keep this manual for future

reference.

The product may only be used as set out in

the assembly and operating instructions. The

guarantee is only valid if the product is used

in the manner intended and in accordance

with the instructions.

Application area

Panther 6-15 is a range of very quiet and ef-

ﬁcient fan heaters for stationary use. They are

intended for heating, drying and ventilation in

e.g. workshops, sport halls, shops, assembly

rooms and drying rooms.

The mixing cabinet (accessory) allows heating

and ventilation to be combined, through mix-

ing the return air and outdoor air.

Protection class: IP44

Function

The air is carried through the heater by a fan

and heated by non-corrosive elements which

are regulated by the built-in thermostat with a

range of +5 - +35°C. The air speed is adjusta-

ble in three steps.

Switching on or off, selecting half or full

output and regulating the RPM is performed

through the control panel PP15 (ordered sepa-

rately) which is wall mounted for easy access.

The appliance is protected from overheating

via a built-in temperature limiter. To reset,

see Overheating.The heater is mounted on a

wall with a bracket, which allows direction of

the air stream in several directions, straight

ahead, to the left, to the right and down.

Installation

The fan heaters are intended for wall moun-

ting. The appliance must not be placed direct-

ly under a wall-outlet.

N.B.! The minimum distances given in ﬁg. 2

and 3 must be kept. The fan heaters must not

be mounted on the ceiling.

• Loose the bracket from the appliance by

unscrewing the bolts.

• Mark holes by means of the loose bracket.

Installation with mixing cabinet

Mixing cabinet PBS is available as an acces-

sory and consists of an outer wall grille and

a walling-in frame. The walling-in frame and

outer wall grille are built or screwed to the

wall. The mixing cabinet and the unit are

then ﬁtted. See diagram 2. The hand control-

ler (PHR01, accessory) consists of a lever, a

wall bracket, a control ball and two associated

joints. A pull-rod is used between the joints

(not included).

Electrical installation

The electrical installation should be carried

out by a qualiﬁed electrician in conformity

with prevailing regulations. The appliance

should be preceded by an all-pole switch with

at least 3 mm breaking gap. There are several

ways to connect depending on the desired

function.

On delivery the appliance is equipped with

connections on the terminal block. With a

connection between

terminals 14 and 15,

the fan RPM will be

controlled by the regulation and the heat by

the thermostat. Without the connection the

thermostat will control both fan RPM and

heat.

When accessories are connected or when

several

heaters are connected to each other and con-

trolled by a common accessory.

Between terminals 1 and 13, a 230V~ alarm

signal can be obtained. When the temperature

limiter is triggered, the voltage will drop to

zero.

On delivery the Panther 6 – 15 fan heaters are

for

400V 3N~. SE135 can be connected to both

440V3~ and 500V3~.

• Drill holes for the ﬁxing plugs.

• Mount the bracket.

• Mount the fan heater on the bracket and

adjust the heater to desired vertical and

horizontal angles.

• Screw the bottom bolt in and tighten all

bolts.

Panther 6/15

Type Output

[kW]

Voltage

[V]

Min.area

[mm2]

All control 230V~ 0,75

SE 06 6 400V 3N~/230V 3~ 1,5/2,5

SE 09 9 400V 3N~/230V 3~ 2,5/6

SE 12 12 400V 3N~/230V 3~ 4/10

SE 15 15 400V 3N~/230V 3~ 6/16

SE 135 13,5 500V 3~/440V 3~ 4/2,5

Overheating

If the temperature limiter has been triggered

due to overheating, reset as follows:

• Disconnect the electricity with the all-pole

switch.

• Investigate the matter and repair the fault.

• Reset by opening the lid and pushing the

red button on top of the temperature limi-

ter until a click sound is heard.

• Put on the lid and reconnect the heater.

Maintenance

The motor and other components are mainte-

nance-free. Dust and dirt may cause overhea-

ting and danger of ﬁre. The appliance must

therefore be cleaned regularly.

Safety

• For all installations of electrically heated

products should a residual current circuit

breaker 300 mA for ﬁre protection be used.

• Ensure that the area around the intake and

exhaust grille is kept free from material

which could prevent the air ﬂow through

the appliance.

• The appliance has hot surfaces during

operation!

• The appliance must not be covered either

with clothes or similar material since

overheating of the appliance can result in a

ﬁre hazard.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure

that they do not play with the appliance.

The heaters can be reconnected to 230V3~

according to ﬁg. 4.

The connection should be made with a cable

type S05VV-U, A05VV-R or similar. For con-

trol H05VV5-F0,75 mm² or similar may be

used.

On the back of the appliance there are knock-

outs. Cable-glands used must guarantee the

protection class requirements!

When several heaters are connected to each

other and controlled by a common accessory

it should be stated in the group centre that

“The fan heaters are fed from more than one

group supply”.

Start-up (E)

When the unit is used for the ﬁrst time or

after a long period of disuse, smoke or odour

may result from dust or dirt that has collected

on the element. This is completely normal

and disappears after a short time.

Residual current circuit breaker (E)

When the installation is protected by means

of a residual current circuit breaker, which

trips when the appliance is connected, this

may be due to moisture in the heating ele-

ment. When an appliance containing a heater

element has not been used for a long period

or stored in a damp environment, moisture

can enter the element.

This should not be seen as a fault, but is

simply rectiﬁed by connecting the appliance

to the mains supply via a socket without a

safety cut-out, so that the moisture can be

eliminated from the element. The drying time

can vary from a few hours to a few days. As

a preventive measure, the unit should occa-

sionally be run for a short time when it is not

being used for extended periods of time.

Art.no 201398, 2013-05-30 HH/ SÄ

Main ofﬁ ce

Frico AB Tel: +46 31 336 86 00

Box 102 Fax: +46 31 26 28 25

SE-433 22 Partille [email protected]

Sweden www.frico.se

For latest updated information and information

about your local contact: www.frico.se

Frico panther 6 Original Instructions Manual

Frico panther 6 Original Instructions Manual

Frico panther 6 Original Instructions Manual

Related papers

Other documents