Fujitsu ASWG09JMCB Operating instructions

Fujitsu
Brand
Fujitsu
Model
ASWG09JMCB
Category
Split-system air conditioners
Type
Operating instructions

This manual is also suitable for

En-1
PART No. 9333003160-02
中國語
English
Safety Precautions
To prevent personal injury, or property damage, or property damage, read this section carefully before you use this product, and be sure to comply
following safety precautions.
Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classied as follows:
WARNING CAUTION
This mark warns of death or serious injury. This mark warns of injury or damage to property.
This mark denotes an action that is PROHIBITED.
This mark denotes an action that is COMPULSORY.
WARNING
• This unit contains no user-serviceable parts. Always consult
authorized service personnel for repairing, installation, and
relocation of this product.
Improper installation or handling will cause leakage, electric
shock, or re.
• In the event of a malfunction such as burning smell,
immediately stop operation of the air conditioner, and
disconnect all the power supply by turning off the electrical
breaker or disconnecting the power plug. Then consult
authorized service personnel.
• Take care not to damage the power supply cable.
If it is damaged, it should only be replaced by authorized
service personnel.
• In the event of refrigerant leakage, be sure to keep away
from re or any ammables, and consult authorized service
personnel.
• If you see lightning or hear thunder, there might be a
lightning strike.
To prevent electric shock hazard, turn off the air conditioner
by using the remote controller, and do not touch the unit or
the power plug during thunderstorm.
• T
his appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
• Do not install the unit in area lled with mineral oil such as a
factory or area containing a large amount of splashed oil or
steam such as a kitchen.
• Do not start or stop the operation of this product by inserting
or pulling out the power plug, or by turning on or off the
circuit breaker.
• Do not use inammable gases near the unit.
• Do not expose yourself directly to the cooling airow for
many hours.
• Do not insert your ngers or any other objects into outlet
port, open panel, or intake grille.
• Do not operate with wet hands.
CAUTION
• Provide occasional ventilation during use.
• Always operate the unit with air lters installed.
• Ensure that any electronic equipment is at least 1 meter
away from either the indoor unit or outdoor unit.
• Unplug the power supply cable when not using the indoor
unit for an extended period.
• After long period of use, check whether the installation stand
does not deteriorate to prevent the unit from falling down.
• The airow direction and the room temperature should be
carefully considered when you use this product in a room
with infants, children, elderly or sick persons.
• Do not direct the airow at replaces or heating apparatus.
• Do not block or cover the intake grille and the outlet port.
• Do not apply any heavy pressure to radiator ns.
• Do not climb on, place objects on, or hang objects from the unit
.
• Do not place vase or water container on the unit.
• Do not place any other electrical products or household
belongings under indoor unit or outdoor unit.
Dripping condensation from the unit might get them wet, and
may cause damage or malfunction of your property.
• Do not expose the unit directly to water.
• Do not use this product for preservation of food, plants,
animals, precision equipment, art work, or other objects. This
may cause quality deterioration of those items.
• Do not expose animals or plants to the direct airow.
• Do not drink the drainage from the air conditioner.
• Do not pull the power supply cable to disconnect the plug.
• Do not touch the aluminum ns of heat exchanger built-in
the indoor or outdoor unit to avoid personal injury when you
install or maintain the unit.
Indoor Unit
ASWG09JMCB
ASWG12JMCB
Outdoor Unit
AOWG09JMCB
AOWG12JMCB
AIR CONDITIONER
Wall Mounted Type
COOL MODEL
OPERATING MANUAL
Before using this product, read these instructions
thoroughly and keep this manual for future reference.
Contents
Safety Precautions ............................................................... 1
Indoor Unit Overview and Operations .................................. 2
Remote Controller Overview and Operations ....................... 3
Care and Cleaning................................................................ 5
Troubleshooting .................................................................... 7
En-2
OPERATING MANUAL
1 Intake grille
Before starting operation, make sure that the intake grille has been
shut completely. Incomplete closing might have an effect on the
proper working or performance of the product.
2 Manual AUTO button
Use when you lost the remote controller or remote control malfunction
occurs.
Status Action Mode or operation
In operation Press more than 3 seconds. Stop
Stopping Press more than 3 seconds and
less than 10 seconds.
AUTO
Press more than 10 seconds.
(Only for servicing.*)
Forced cooling
After cleaning Press less than 3 seconds. Filter indicator reset
*:To stop forced cooling, press this button or START/STOP button on
the remote controller.
3 Front panel
4 Vertical airow direction louver
Each time you press SET button on the remote controller, the angle
of the vertical airow direction louver moves as follows:
1
2
3
4
5
6
7
COOL, DRY or FAN mode
1 2
3
765
* *
4
*: Default setting in each mode.
• Do not adjust by hand.
• At the beginning of AUTO mode, it may stay position 1 for a while
for adjustment.
• If you set the angle to position 4–7 for more than 30 minutes in
COOL or DRY mode, they automatically return to position 3.
In COOL or DRY mode, if the angle is set to position 4–7 for many hours,
condensation may be formed, and the drips may wet your property
.
5 Power diffuser
In conjunction with movement of the vertical airow direction louver,
the angle of the power diffuser moves as follows:
Vertical airow
direction louver
Power diffuser
3
76
5
4
2
1
321
4
• In SWING operation, power diffuser does not move.
6 Drain hose
7 Remote control signal receiver
CAUTION
For appropriate signal transmission between remote controller and
the indoor unit, keep the signal receiver away from following items
:
- Direct sunlight or other strong light
- Flat-panel television screen
In rooms with instantaneous uorescent lights, such as in-
verter type ones, the signal may not be transmitted properly. In
such a case, consult the store that you purchased the product
.
8 ECONOMY indicator (green)
Lights in ECONOMY operation.
9 TIMER indicator (orange)
Lights in TIMER operation, and blinks slowly when the timer setting
error is detected.
As for the timer setting error, refer to “Auto-restart function” on page 4.
10
OPERATION indicator (green)
Lights in normal operation.
6
1
3
4
5
8
9
10
11
13
2
12
7
11
Horizontal airow direction louvers
CAUTION
Before you adjust the horizontal airow direction, make sure that
the vertical airow direction louver has been stopped completely
.
Adjust two knobs by hand.
See page 5
12
Air lter
Easy-to-care air lters resist mildew growth.
See page 6
13
Air cleaning lters
Purify or deodorize the air, and provide fresh airow.
Indoor unit accessories
Remote
controller
Batteries Air cleaning lters Filter holders
Remote controller
holder
Tapping screws
WARNING
Take care to prevent infants and young children from acciden-
tally swallowing the batteries.
Remote controller holder installation
Slide up
Pull out
3
Insert
Press in
2
Screws
1
Indoor Unit Overview and Operations
En-3
AIR CONDITIONER Wall Mounted Type
OPERATING MANUAL
CAUTION
• To prevent malfunction or damage of the remote controller:
- Place remote controller at where will not be exposed to
direct sunlight or excessive heat.
- Remove batteries if the product is not going to be used for
an extended period.
- Exhausted batteries must be removed immediately, and
be disposed according to the local laws and regulations of
your region.
• If leaking battery uid comes in contact with your skin, eyes,
or mouth, immediately rinse with plenty of clean water, and
consult your physician.
• Obstacles such as a curtain or wall between the remote
controller and the indoor unit may affect the appropriate
signal transmission.
• Do not apply strong shocks to the remote controller.
• Do not pour water on the remote controller.
• Do not attempt to recharge dry batteries.
Battery (AAA/R03/LR03 × 2) loading
Notes:
• Use specied type of battery only.
• Do not use new battery and used battery together.
• Batteries can be used about 1 year in ordinary use.
• If the remote control range noticeably got shorten, replace the
batteries, and press RESET button.
1
2
3
You can quickly start the operation with following 3 steps:
1 START/STOP button
2 MODE button
Switches operation mode in following order.
AUTO COOL DRY FAN
3 SET TEMP. (temperature) buttons
Set desired temperature.
Temperature setting range
AUTO 18–30 °C
COOL/DRY 18–30 °C
*:Temperature control is not available in FAN mode.
4 FAN button
Controls the fan speed.
AUTO HIGH MED LOW QUIET
• When AUTO is selected, the fan speed is automatically adjusted
according to the operation mode.
5 SET button
Adjusts the vertical airow direction.
6 SWING button
Starts or stops automatic swing of the vertical airow direction louver.
• Each time you press the button, the vertical airow direction louver
swings as follows:
1
2
3
4
5
6
7
1 2
3
76
5
4
COOL, DRY or FAN1
mode
FAN2
mode
Note:
• SWING operation may stop temporarily when the fan in the unit is
rotating at very low speed or stopping.
• In FAN mode, either of swing direction 1
↔
3 or 4
↔
7 is performed
in accordance with the vertical airow direction previously set before
you start the SWING operation.
Remote Controller Overview and Operations
5
6
15
12
11
13
14
2
3
16
4
10
7
1
9
8
7 RESET button
When you press the RESET button, press it gently by using the tip of
a ballpoint pen or other small object in correct direction as shown in
this gure.
RESET
8 TIMER CANCEL button
Cancels the set timer.
9 ON TIMER button
Each time you press the button, the time changes as follows:
hours
0.5 1.0 1.5
2.0
...
9.0 9.5 10 11 12
• Set the time while the indicator on the remote controller display
is blinking.
10
OFF TIMER button
Each time you press the button, the time changes as follows:
hours
0.5 1.0 1.5
2.0
...
9.0 9.5 10 11 12
• Set the time while the indicator on the remote controller display
is blinking.
: The setting must be done within about 3 seconds during the indi-
cator stays solid.
: The button is controllable only when the air conditioner is on.
(continued)
En-4
OPERATING MANUAL
Program timer (combined use of the ON timer and the OFF timer)
You can set an integrated ON–OFF or OFF–ON timer as follows:
ON–OFF Set the ON timer rst.
Then set the OFF timer by the air conditioner starts opera-
tion controlled with the ON timer earlier set.
OFF–ON
Set the OFF timer rst.
Then set the ON timer by the air conditioner stops opera-
tion controlled with the OFF timer earlier set.
The timer that is set later starts counting down after the counting
down of the preceding timer is nished.
Note:
If you change the setting value for the timer after the program timer is
set, the counting down of the timer will be reset at that moment.
11
SLEEP TIMER button
Each time you press the button, the time changes as follows:
1.0 2.0 3.0 5.0 7.0
CANCEL
hours
9.0
• Set the time while the indicator on the remote controller display
is blinking.
To repeat the timer, press the button when the indicator is not
displayed.
To help you to fall asleep comfortably and prevent excessive
cooling in sleep, the SLEEP timer controls the temperature setting
automatically in accordance with the set time shown as follows. The
air conditioner completely turns off after the set time has elapsed.
Set
temperature
In COOL or DRY mode
Set time
1 hour
1 °C 2 °C
Note for TIMER settings:
Any interruption of the power supply, such as a blackout or cutting off
of a circuit breaker, makes the set internal clock go wrong. In such a
case, the TIMER indicator on the indoor unit blinks, and you need to
readjust the setting.
12
TEST RUN button
Only used for the initial test in the unit installation.
Do not press this button under normal use because it will cause
incorrect operation.
• During the test run, the OPERATION indicator and the TIMER
indicator blink simultaneously.
• To quit the test run that is started unintentionally, you need to turn
off the air conditioner by pressing the START/STOP button.
13
ECONOMY button
Starts ECONOMY operation that saves more electricity consumption
than the other operations with a conservative adjustment of the room
temperature.
When you press the button, the ECONOMY indicator on the indoor
unit turns on.
• In COOL mode, the room temperature will be adjusted at a few
degree higher than the dened temperature.
• Especially in COOL mode, you can have improved dehumidication
without signicantly lowering the room temperature.
Notes:
• In COOL mode, the maximum output of this operation is
approximately 70 % of usual air conditioning operation.
• This operation cannot be performed during temperature monitoring
by AUTO mode.
14
POWERFUL button
Starts POWERFUL operation that enables quick cooling down of the
room.
When you press the button to start the POWERFUL operation, the
indoor unit emits 3 short beeps.
POWERFUL operation is automatically turned off in the following
situations:
• Adjusted room temperature reached to the dened temperature in
temperature setting in COOL or DRY mode.
• 20 minutes have passed after nishing the POWERFUL operation
mode setting.
It is not turned off automatically during setting of the POWERFUL
operation.
Notes:
• The airow direction and the fan speed are controlled automatically.
• This operation cannot be performed simultaneously with ECONOMY
operation.
To return to normal operation, press the button again. Then the indoor
unit emits 2 short beeps.
15
Remote controller display
In this section, all the possible indicators are displayed for description.
In actual operation, the display is linked with the button operation, and
only shows the necessary indicators for each setting.
16
Signal transmitter
Aim to signal receiver of the indoor unit properly.
• Signal transmit indicator on the remote controller display shows
that signal from the remote controller is being transmitted.
• Operating range is approximately 7 m.
• You will hear a beep if the transmitted signal has been sent properly.
If there is no beep, press the button on the remote controller again.
Auto-restart function
In event of power interruption such as a blackout, the air
conditioner stops once. But it restarts automatically and
performs previous operation when the power supply is resumed.
If any power interruption occurs after the timer is set, counting
down of the timer will be reset.
After the power supply is resumed, the TIMER indicator on the
indoor unit blinks to notify you that there has been a timer fault.
In such a case, reset the timer for your opportune time.
Malfunctions caused by other electrical devices:
Use of other electrical appliances such as an electric shaver or
nearby use of a wireless radio transmitter may cause the malfunction
of the air conditioner.
If you encounter such a malfunction, turn off the circuit breaker once.
Then turn it on again, and resume operation by using the remote
controller.
Remote Controller Overview and Operations
En-5
AIR CONDITIONER Wall Mounted Type
OPERATING MANUAL
Care and Cleaning
CAUTION
• Before cleaning the indoor unit, be sure to turn it off and all the power supply has been disconnected.
• Before starting operation, make sure that the intake grille has been shut completely. Incomplete closing of the intake grille might have an
effect on the proper working or performance of the air conditioner.
• Do not touch the aluminum ns of heat exchanger built-in the indoor unit to avoid personal injury when you maintain the unit.
• Do not expose the indoor unit to liquid insecticides or hair sprays.
• Do not stand on slippery, uneven or unstable surfaces when you maintain the unit.
Daily care
When cleaning the indoor unit body, mind the following:
• Do not use water hotter than 40 °C.
• Do not use scouring cleanser, volatile solvents such as benzene or
thinner.
• Wipe the unit gently by using soft cloth.
Cleaning the intake grille
1
Open the intake grille in direction of the arrow
a
. While gently
pressing the left and right mounting shafts of the intake grille
outward
b
, remove the intake grille in direction of the arrow
c
.
a
a
b
c
b
c
2
Wash the intake grille gently with water or wipe it gently with a
soft cloth moisten with warm water.
Then wipe it with a dry and soft cloth.
3
While holding the grille horizontal, set the left and right mounting
shafts into the pillow blocks at the top of the panel
a
. To latch
each shaft properly, insert the shaft until it snaps.
Then close the intake grille
b
.
a
a
b
b
4
Press 4 places on the intake grille to close it completely.
Cleaning the air lters
Mind that you have a periodical cleaning of the air lters to prevent
reducing the operation efciency of the product.
Using of clogged air lter with dust will lower the product performance,
and may cause airow reduction or increase of operating noise.
Clean the air lters once every 2 weeks under normal use.
1
Open the intake grille.
(Refer to
a
of step 1 in “Cleaning the intake grille”.)
2
While holding the intake grille with your hand, pull up the handle
a
of the lter in direction of the arrow and release the 2 claws
b
.
Then pull the lter out with gently sliding it downward
c
.
a
b
b
a
c
3
Filter holder and air cleaning lter are attached on the rear side
of the air lter. Remove them from the air lter by unlatching each
corner of the lter holder
d
.
d
d
d
d
4
Remove dust by using a vacuum cleaner or by washing the lter.
When you wash the lter, use neutral household detergent and
warm water.
After rinse the lter well, dry it throughly in a shaded place before
you reinstall it.
5
Attach the air cleaning lter and the lter holder to each air lter.
6
Attach the air lter with aligning both side of the lter with the front
panel, and push in the lter fully.
Note:
Make sure that 2 claws are rmly snapped to the guide holes on
the panel.
7
Close the intake grille rmly.
(Refer to step 4 in “Cleaning the intake grille”.)
En-6
OPERATING MANUAL
Following 2 types of air cleaning lters are used in this product.
When you replace them, purchase dedicated air cleaning lters for this
product.
APPLE-CATECHIN FILTER: UTR-FA16
(1 sheet)
With using static electricity, puries the air by removing ne particles
or dust such as tabacco smoke or plant pollen.
• This lter is disposable. Do not wash or reuse it.
• Once you open the package, use it as soon as possible. The
cleaning effect is reduced if the lter is left the package opened.
• Replace the lter once every 3 months under normal use.
• With setting the fan speed high, the air cleaning effect increases.
ION DEODORIZATION FILTER (light blue): UTR-FA16-2
(Light blue, 1 sheet)
Contained super micro-ceramic particles produce negative air ions,
that is considered to have deodorizing effect, absorb and reduce
room smell.
• To maintain the deodorizing effect, clean the lter once every 3
months as follows:
1. Remove the ion deodorization lter.
2. Flush the lter with high-pressure hot water until the surface of
the lter is covered with water.
3. Wash the lter gently with diluent neutral detergent. Do not wash
it by wringing or rubbing to prevent reducing the deodorizing
effect by damage.
4. Rinse the lter well with water ow.
5. Dry the lter throughly in shaded place.
6. Reinstall the ion deodorization lter to the indoor unit.
• Replace the lter once every 3 years under normal use.
After extended non-use of the unit
If you have shut down the indoor unit for 1 month or more, perform the
FAN operation for half a day to dry the internal parts throughly before
you perform normal operation.
Additional inspection
After long period of use, accumulated dust inside the indoor unit may
reduce the product performance even if you have maintained the unit
with instructed daily care or cleaning procedures written in this manual.
In such a case, the product inspection is recommended.
For more information, consult authorized service personnel.
Filter Indicator Reset (Special setting)
• This function can be used if set correctly during installation.
Please consult authorized service personnel in order to use this function
.
• Clean the air lter when the indicator lamp show the following;
ECONOMY indicator lamp Flashes 3 times, at intervals of 21 seconds
After cleaning, reset the lter indicator by pushing the “MANUAL
AUTO” button on the indoor unit for 3 seconds or less.
Replacing the air cleaning lter
1
Remove the air lter. (Refer to step 1 in “Replacing the air lter”.)
2
Release 2 latches
a
of the lter holder, and turn over the holder
in direction of arrow
b
.
Remove the soiled air cleaning lter
c
.
Note:
Air cleaning lter is attached on each air lter.
a
a
b
c
3
Attach new or maintained air cleaning lter
d
to the lter holder.
New air cleaning lter can be attached to either of the right holder
or the left holder.
d
4
Latch 2 corners of the lter holder
e
to the air lter rmly.
e
e
5
Reinstall the air lter. (Refer to step 6 in “Cleaning the air lter”.)
6
Close the intake grille rmly.
(Refer to step 4 in “Cleaning the intake grille”.)
Care and Cleaning
En-7
AIR CONDITIONER Wall Mounted Type
OPERATING MANUAL
WARNING
In following events, immediately stop operation of the air conditioner, and disconnect all the power supply by turning off the electrical
breaker or disconnect the power plug. Then consult your dealer or authorized service personnel.
As long as the unit is connected to the power supply, it is not insulated from the power supply even if the unit is turned off.
• Unit smells of something burning or emits smoke
• Water leaks from the unit
Following symptoms do not indicate the product malfunction, but they are normal functions or characteristics of this product.
Symptom Cause See page
Operation is delayed after
restart.
To prevent blowout of the fuse, the compressor will not operate during the protection circuit is working
for about 3 minutes after sudden OFF→ON operation of the power supply.
–
Noise is heard. • During the operation or immediately after stopping the air conditioner, refrigerant owing sound
may be heard. And it is particularly noticeable for 2–3 minutes after starting operation.
• During the operation, a slight squeaking sound produced by the minute expansion and contraction
of the front panel caused by temperature change may be heard.
–
Smell coming from the unit. Absorbed room smell generated from interior textile, furniture, or cigarette smoke into the air condi-
tioner may be emitted.
–
Mist or steam is emitted from
the unit.
In COOL or DRY mode, a thin mist generated by condensation formed with sudden cooling process
may be emitted.
–
Airow is weak or stops In DRY mode, the indoor unit operates at low fan speed to adjust the room humidity, and may stop
from time to time.
–
When the fan speed is set to “QUIET”, the fan rotates at very low speed and the airow is reduced. –
When monitoring operation is performed in AUTO mode, the fan rotates at very low speed. –
When the lter sign is set, the LED lamp may ash. In this case, please refer to the “Filter Indicator Reset (Special setting)”.
Before you call for or request servicing, troubleshoot a problem by performing following checks:
Symptom Diagnostic See page
Does not operate at all.
Has the circuit breaker been turned off?
Has there been a power outage?
Has a fuse blown out or the circuit breaker been tripped?
–
Is the timer operating?
3
Poor cooling performance.
Is the air lter dirty?
5
Is the intake grille or outlet port of indoor unit blocked?
–
Is the room temperature adjusted appropriately?
3
Is a window or door left opened?
Is direct or strong sunlight shinning into the room in cooling operation?
Are there other heating apparatus or computers operating, or too many people in the room in cool-
ing operation?
–
Is the fan speed set to “QUIET”?
When the fan speed setting is set to “QUIET”, noise reduction is prioritized and the air-conditioning
performance may become lower. If the volume of provided airow is not agreeable to your prefer-
ence, set the fan speed to “LOW” or higher fan speed.
3
The unit operates differently
from the remote controller
setting.
Are the batteries used in the remote controller exhausted?
Are the batteries used in the remote controller loaded properly?
3
Immediately stop operation and turn off the electrical breaker in following cases. Then consult authorized service personnel.
• The problem persists even if you perform these checks or diagnostics.
• The OPERATION indicator and TIMER indicator blink while the ECONOMY indicator is blinking fast.
Troubleshooting
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Fujitsu ASWG09JMCB Operating instructions

Fujitsu
Brand
Fujitsu
Model
ASWG09JMCB
Category
Split-system air conditioners
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents