JVC UX-F72MD User manual

Category
CD players
Type
User manual

This manual is also suitable for

INSTRUCTIONS
UX-F70MD — Consists of CA-UXF70MD and SP-UXF70MD
UX-F72MD — Consists of CA-UXF72MD and SP-UXF72MD
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
GVT0061-003A
[UB]
MICRO COMPONENT MD SYSTEM
COLOR
MD GROUP
MD TITLE
IMPUT/EDIT
CLOCK
/TIMER
FM MODE
DISPLAY
/CHARA
MD TITLE
SEARCH
SOUND
MODE
AHB
PRO
SET
CANCEL
CD
DIMMER
1 2 3
ENTER
FM/AM
/AUX
REV.MODE
REPEAT
TAPE
STANDBY/ON
SLEEP
PLAY MODE
BEEP
VOLUME
MD
4 5 6
7 8 9
10
0
+
10
RM-SUXF70MDU
MARK
STANDBY/ON
COMPACT
DIGITAL AUDIO
MICRO COMPONENT MD SYSTEM UX-F70MD
PHONES
COLOR
MD GROUP
MD TITLE
IMPUT/EDIT
CLOCK
/TIMER
FM MODE
DISPLAY
/CHARA
MD TITLE
SEARCH
SOUND
MODE
AHB
PRO
SET
CANCEL
CD
DIMMER
1 2 3
ENTER
FM/AM
/AUX
REV.MODE
REPEAT
TAPE
STANDBY/ON
SLEEP
PLAY MODE
BEEP
VOLUME
MD
4 5 6
7 8 9
10
0
+
10
RM-SUXF70MDU
MARK
STANDBY/ON
COMPACT
DIGITAL AUDIO
MICRO COMPONENT MD SYSTEM UX-F72MD
PHONES
CA-UXF72MDCA-UXF70MDSP-UXF70MD SP-UXF70MD
SP-UXF72MD
SP-UXF72MD
UX-F70MD[UB]COVER_f 01.7.10, 2:54 PM1
– G-1 –
Caution –– STANDBY/ON button!
Disconnect the mains plug to shut the power off completely (the
STANDBY/ON lamp goes off).
The STANDBY/ON button in any position does not disconnect
the mains line.
When the unit is on standby, the STANDBY/ON lamp lights red.
When the unit is turned on, the STANDBY/ON lamp lights green.
The power can be remote controlled.
Warnings, Cautions and Others
UX-F70MD[UB]SAFETY_f 01.7.10, 2:55 PM1
English
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
– G-2 –
CAUTION
Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
Do not place any naked flame sources, such as
lighted candles, on the apparatus.
When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed
strictly.
Do not use this apparatus in a bathroom or places
with water. Also do not place any containers filled with
water or liquids (such as cosmetics or medicines,
flower vases, potted plants, cups, etc.) on top of this
apparatus.
UX-F70MD[UB]SAFETY_f 01.7.10, 2:55 PM2
Front view Side view
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front: No obstructions and open spacing.
2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions
below.
3 Bottom: Place on the level surface. Maintain an adequate air path for ventilation by
placing on a stand with a height of 10 cm or more.
UX-F70MD
UX-F72MD
1 cm
15 cm
15 cm
15 cm
10 cm
UX-F70MD
UX-F72MD
1 cm
15 cm
15 cm
15 cm
– G-3 –
UX-F70MD[UB]SAFETY_f 01.7.10, 2:55 PM3
English
– G-4 –
REPRODUCTION OF LABELS /
CLASS 1
LASER PRODUCT
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to
beam.
3. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
DANGER: Invisible laser
radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE
TO BEAM. (e)
ADVARSEL: Usynlig laser-
stråling ved åbning, når
sikkerhedsafbrydere er ude
af funktion. Undgå udsæt-
telse for stråling (d)
VARNING: Osynlig laser-
strålning när denna del är
öppnad och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO: Avattaessa ja suo-
jalukitus ohitettaessa olet
alttiina näkymättömälle
lasersäteilylle. Älä katso
säteeseen. (f)
IMPORTANT FOR LASER PRODUCTS /
1 CLASSIFICATION LABEL, PLACED ON REAR ENCLO-
SURE
2 WARNING LABEL, PLACED INSIDE THE UNIT
UX-F70MD[UB]SAFETY_f 01.7.10, 2:55 PM4
– 1 –
English
Introduction
About This Manual
This manual is organized as follows:
This manual mainly explains playback and editing
operations using the remote control, and the other
operations such as recording operations using the
buttons on the main unit.
You can use the buttons both on the remote control
and on the main unit for the same operations if they
have the same or similar names (or marks), unless
mentioned otherwise.
Basic and common information that is the same for
many functions is grouped in one place, and is not
repeated in each procedure. For instance, we do not
repeat the information about turning on/off the unit,
setting the volume, changing the sound effects, and
others, which are explained in the section “Basic and
Common Operations” on pages 10 – 13.
The following marks are used in this manual:
Gives you warning and caution to prevent
from damage or risk of fire/electric shock.
Furthermore, gives you information which
is not good for obtaining the best possible
performance from the unit.
Gives you information and hints you had
better know.
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
Power sources
When unplugging the unit from the wall outlet, always
pull the plug, not the AC power cord.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lens inside the unit in the
following cases:
After starting heating in the room
In a damp room
If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, then plug it in
again.
Others
Should any metallic object or liquid fall into the unit,
unplug the AC power cord and consult your dealer before
operating any further.
If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
If anything goes wrong, unplug the AC power cord and
consult your dealer.
Precautions
Installation
Install in a place which is level, dry and neither too hot
nor too cold — between 5˚C (41˚F) and 35˚C (95˚F).
Install the unit in a location with adequate ventilation to
prevent internal heat buildup in the unit.
Leave sufficient distance between the unit and the TV.
Keep the speakers away from the TV to avoid
interference with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM1
– 2 –
English
Contents
Recording on Tapes ...................................... 35
Before You Start Recording on a Tape ................. 36
Recording FM/AM Broadcasts ............................ 37
Recording CD — CD Synchronized Recording .... 37
Recording MD — MD Synchronized Recording ..
38
Recording the External Equipment ...................... 38
Recording CD onto an MD and a Tape
— CD Synchronized Recording ....................39
Editing MD Groups ...................................... 40
Guidance — MD Group Functions......................41
Introducing MD Group Editing ........................... 42
Forming a Group — FORM GR .......................... 43
Adding a Track to a Group — ENTRY GR ......... 44
Dividing a Group — DIVIDE GR ....................... 44
Joining Two Groups — JOIN GR ........................ 45
Moving a Group — MOVE GR...........................46
Ungrouping Tracks — UNGROUP ..................... 46
Dissolving All Groups — UNGR ALL................ 47
Erasing Tracks in a Group — ERASE GR .......... 47
Editing MD Tracks ....................................... 48
Introducing MD Track Editing ............................ 49
Dividing a Track — DIVIDE...............................50
Joining Two Tracks — JOIN ............................... 50
Moving a Track — MOVE .................................. 51
Erasing Tracks — ERASE ................................... 52
Erasing All Tracks — ALL ERASE .................... 52
Assigning Titles to an MD............................ 53
Assigning the Disc Title, Track Title
and Group Title .............................................. 54
Using the Timers ........................................... 56
Setting the Clock.................................................. 57
Using Recording Timer........................................ 57
Using Daily Timer ............................................... 58
Using Sleep Timer ............................................... 60
Timer Priority.......................................................60
Maintenance .................................................. 61
Additional Information ................................ 62
MD Disc Types .................................................... 62
ATRAC (Adaptive TRansform Acoustic Coding)/
ATRAC3 (
) ........................................ 62
UTOC (User Table Of Contents) ......................... 62
Sound Skip Guard Memory ................................. 62
SCMS (Serial Copy Management System)..........63
HCMS (High-speed Copy Management System) .. 63
MD limitations ........................................... 63
MD/CD Messages.......................................... 64
Troubleshooting ............................................ 65
Specifications................................................. 66
Location of the Buttons .................................. 3
Main Unit ............................................................... 3
Remote Control...................................................... 5
Getting Started................................................ 6
Unpacking .............................................................. 6
Connecting Antennas ............................................. 6
Connecting Speakers..............................................7
Connecting Other Equipment ................................ 8
Putting the Batteries into the Remote Control ....... 9
Basic and Common Operations................... 10
Turning On the Power .......................................... 11
Selecting the Sources and Starting Play .............. 11
Adjusting the Volume...........................................12
Turning On/Off the Key-touch Tone .................... 12
Reinforcing the Bass Sound................................. 12
Selecting the Sound Modes.................................. 12
Setting the Display Illumination ..........................13
Listening to FM and AM Broadcasts.......... 14
Setting the AM Tuner Interval Spacing................ 15
Tuning in a Station ...............................................15
Presetting Stations................................................ 15
Tuning in a Preset Station .................................... 16
Playing Back a CD........................................ 17
Precautions on CD Playback................................18
Playing Back the Entire CD — Normal Play ...... 18
Basic CD Operations ........................................... 19
Programing the Playing Order of the Tracks
— Program Play ............................................ 19
Playing at Random — Random Play ................... 20
Repeating Tracks — Repeat Play ........................ 21
Playing Back an MD..................................... 22
Playing Back the Entire MD — Normal Play...... 23
Basic MD Operations...........................................24
Programing the Playing Order of the Tracks
— Program Play ............................................ 24
Playing at Random — Random Play ................... 25
Playing Tracks in a Group — Group Play ........... 25
Repeating Tracks — Repeat Play ........................ 26
Searching by Title of the Track
— MD Title Search .......................................26
Playing Back a Tape ..................................... 27
Playing Back a Tape............................................. 28
Recording on MDs........................................ 29
Before You Start Recording on an MD ................ 30
Recording FM/AM Broadcasts ............................ 32
Recording CD — CD Synchronized Recording .... 32
Recording Tape
— Tape Synchronized Recording .................. 33
Recording the External Equipment
— Sound Synchronized Recording ...............34
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM2
– 3 –
English
Location of the Buttons
Become familiar with the buttons on your unit.
Main unit
w
e
r
AUTO REVERSE CASSETTE DECK
F M / A M
open/close
STANDBY/ON
COLOR
AUX
VOLUME
TAPE EJECT
MODE
select
MD GROUP
REC MODE
TAPE
M DC D open/close
REC
start
1
2
3
4
5
8
6
7
q
p
9
t
PHONES
MICRO COMPONENT MD SYSTEM
STANDBY/ON
COMPACT
DIGITAL AUDIO
PBC REC
DAIRY SOUND AHB
GROUP
PRO
ST MONO
;
o
i
y
u
Display window on the electronic swing panel
(Top view)
(Front view)
PBC REC
SOUND AHB
GROUP
PRO
DAILY
ST MONO
a
s
d
g
h
f
k
l
j
/
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM3
– 4 –
English
See pages in the parentheses for details.
Main Unit
1 FM/AM button (11, 15)
Pressing this button also turns on the unit.
2 COLOR button (9, 13)
3
STANDBY/ON button (11, 15)
4 CD open/close 0 button (18 – 20)
Pressing this button also turns on the unit.
5 CD 3 ¥ 8 (play/pause) button (11, 18, 19, 32, 37, 39)
Pressing this button also turns on the unit.
6 MODE select and REC start buttons (32 – 34, 37 – 39)
7 Multi operation buttons
4 (reverse search), 7 (stop), and ¢ (forward
search)
8 MD GROUP REC MODE button (32)
9 MD 3 ¥ 8 (play/pause) button (11, 23, 24, 31, 38)
Pressing this button also turns on the unit.
p MD open/close 0 button (23, 25, 55)
Pressing this button also turns on the unit.
q VOLUME + / – buttons (12)
w TAPE 2 3 button (11, 28, 33)
Pressing this button also turns on the unit.
e AUX button (11, 34, 38)
Pressing this button also turns on the unit.
r TAPE EJECT 0 portion (28)
t Cassette holder (28)
y Electronic swing panel
u Display window
i PHONES (
) jack — stereo mini-type (12)
o Remote sensor
; STANDBY/ON lamp (11)
When using the remote control, point it at the remote
sensor on the electronic swing panel.
Display window
a Timer mode indicators
(Timer), DAILY (Daily Timer), and REC
(Recording Timer)
s CD indicator
Lights when CD is in the disc tray.
d Tuner indicator
Lights when the tuner is selected as the source.
f Main display
Shows the source name and other information.
g Tape indicator
Lights when tape is in the cassette holder.
h MD indicator
Lights when MD is in the loading slot.
j GROUP indicator
Lights when group recording function is activated.
k AHB (Active Hyper Bass) PRO indicator
l SOUND indicator
/ ST and MONO indicators
Continued
STANDBY/ON
COMPACT
DIGITAL AUDIO
MICRO COMPONENT MD SYSTEM
PHONES
1
2
3
4
5
6
7
8
9
10
0
+
10
RM-SUXF70MDU
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM4
– 5 –
English
Remote Control
1 DIMMER button (13, 57)
2 COLOR button (9, 13)
3 CLOCK/TIMER button (57 – 59)
4 MD GROUP button (43 – 47, 54)
5 MD TITLE INPUT/EDIT button (43 – 47, 50 – 52, 54)
6 DISPLAY/CHARA (character) button (16, 19, 24, 26,
28, 31 – 34, 37 – 39, 54)
7 MD TITLE SEARCH button (26)
8 SET button
9 ENTER button (26, 43 – 47, 50 – 52, 55)
p CANCEL button
q FM/AM/AUX button (11, 15, 16)
Pressing this button also turns on the unit.
w CD 3 ¥ 8 (play/pause) button (11, 18 – 20)
Pressing this button also turns on the unit.
e Multi operation buttons
4 (reverse search), 7 (stop), and ¢ (forward
search)
r SOUND MODE button (12)
t AHB (Active Hyper Bass) PRO button (12)
y REV. (reverse) MODE button (28)
u
STANDBY/ON button (11, 15, 58, 59)
i FM MODE button (15)
o SLEEP button (60)
; Number buttons
1 – 10, +10 buttons
Character entry buttons (A – Z, 0 – 9)
a + / = buttons (13, 26, 50, 54, 55)
s PLAY MODE button (19, 20, 24 – 26)
d REPEAT button (21, 26)
f MD 3 ¥ 8 (play/pause) button (11, 23 – 26, 31)
Pressing this button also turns on the unit.
g TAPE 2 3 button (11, 28)
Pressing this button also turns on the unit.
h BEEP button (12)
j VOLUME + / – buttons (12)
10
COLOR
MD GROUP
MD TITLE
INPUT/EDIT
CLOCK
/TIMER
DISPLAY
/CHARA
MD TITLE
SEARCH
SOUND
MODE
AHB
PRO
SET
CANCEL
CD
DIMMER
1 2 3
ENTER
FM/AM
/AUX
REV.MODE
REPEAT
TAPE
STANDBY/ON
SLEEP
PLAY MODE
MARK
BEEP
VOLUME
MD
4 5 6
7 8 9
10
0
+
10
1
7
8
9
5
6
p
e
r
t
i
o
;
s
d
a
2
3
4
q
w
j
y
u
f
g
h
RM-SUXF70MDU
FM MODE
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM5
– 6 –
English
Getting Started
Unpacking
Make sure that you have all the following items.
The number in the parenthesis indicates the quantity of the
pieces supplied.
FM antenna (1)
AM loop antenna (1)
AC power cord (1)
Remote control (1)
Batteries (2)
Spacers (2)
If anything is missing, consult your dealer immediately.
Outdoor FM antenna
(not supplied)
A 75 antenna with coaxial type
connector should be used.
To connect an outdoor FM antenna
Before connecting it, disconnect the supplied FM antenna.
Continued
ANTENNA
FM(75)
COAXIAL
AM EXT
AM LOOP
Connecting Antennas
FM antenna
1
Attach the FM antenna to the FM (75 ) COAXIAL
terminal.
2
Extend the FM antenna.
3
Fasten it up in the position which gives you the best
reception.
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary
measure. If reception is poor, you can connect an outdoor FM
antenna.
FM antenna (supplied)
ANTENNA
FM(75)
COAXIAL
AM EXT
AM LOOP
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM6
– 7 –
English
1
If cords are covered with insulation, twist the core
of the cord at the end of each cord, then remove the
insulation.
2
Connect the AM loop antenna to the AM LOOP
terminals as illustrated.
3
Turn the AM loop antenna until you have the best
reception.
AM antenna
To connect an outdoor AM antenna
When reception is poor, connect a single vinyl-covered
wire to the AM EXT terminal and extend it horizontally.
The AM loop antenna must remain connected.
For better reception of both FM and AM
Make sure the antenna conductors do not touch any other
terminals and connecting cords.
Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.
AM loop antenna
(supplied)
Vinyl-covered wire
(not supplied)
3
ANTENNA
FM(75)
COAXIAL
AM EXT
AM LOOP
1
2
Connecting Speakers
To attach spacers
If you want to place the speakers beside the main unit, it is
recommended to leave a space (1 cm) between the main
unit and the right speaker for ventilation.
It is recommended to attach the spacers (supplied) to the
right speaker as the illustration below:
Spacers (supplied)
The right speaker
By peeling the cover seal from the spacers, you can
attach them to the right speaker.
Opening for ventilation
The main unit
To remove the speaker grilles
The speaker grilles are removable as the illustration below.
Projections
Holes
To remove the speaker grille, insert your fingers at the top
of the speaker grille, then pull towards you. Do the same at
the bottom.
To attach the speaker grille, put the projections of the
speaker grille into the holes of the speaker.
Speaker grille
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM7
– 8 –
English
RL
+
+
RL
SPEAKER IMPEDANCE
MIN 4
Connecting Other Equipment
You can connect the following equipment which can be
used as a playback device.
When you connect and use the equipment, refer also to its
manual supplied.
DO NOT connect other equipment while the
power is on.
DO NOT plug in any equipment until all
connections are complete.
To connect another component such as analog audio
equipment
Be sure that the plugs of the audio cords and the jacks on
the rear of the unit are color-coded: White plugs and jacks
are for left audio signals, and red ones for right audio
signals.
For playing the other equipment through this unit,
connect between the audio output jacks on the other
equipment and LINE IN (AUX) jacks by using audio cords
(not supplied.)
To connect speakers
You can connect the speakers by following the procedure
below.
1
If cords are covered with insulation, twist the core
of the cord at the end of each cord, then remove the
insulation.
2
Open the speaker terminal.
3
Insert the end of the speaker cord to the terminal.
Match the polarity: White cord to red (+) terminal and
black cord to black (–) terminal.
4
Close the speaker terminal on the rear of the unit.
Use only speakers with the speaker impedance — 4 to
16 .
Speaker cord
Speaker cord
Black
Rear of the right
speaker
Rear of the left
speaker
Red
1
Speaker terminals
3,42
To output
Ex. Analog audio
equipment
Continued
R
SPEAKER IMPEDANCE
L
MIN 4
RL
AC IN
LINE IN
(AUX)
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM8
– 9 –
English
Putting the Batteries into the Remote
Control
Insert the batteries — R6P(SUM-3)/AA(15F) — into the
remote control, by matching the polarity (+ and –) on the
batteries with the + and – marking on the battery
compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
R6P(SUM-3)/AA(15F)
1
2
3
DO NOT use an old battery together with a new
one.
DO NOT use different types of batteries together.
DO NOT expose batteries to heat or flame.
DO NOT leave the batteries in the battery
compartment when you are not going to use the
remote control for an extended period of time.
Otherwise, it will be damaged from battery
leakage.
When connecting the AC power cord into a wall outlet, the
unit automatically starts the display illumination.
To stop and cancel the display demonstration, press
COLOR during display illumination — while the unit is
turned off (on standby.)
To start the display illumination manually, press
COLOR again while the unit is turned off (on standby.)
NOW, you can plug the AC power cord.
IMPORTANT: Be sure to check all connections to be done
before plugging the AC power cord into a wall outlet.
1
To the AC IN terminal
AC power cord
(supplied)
2
To a wall outlet
R
SPEAKER IMPEDANCE
L
MIN 4
RL
AC IN
EN01-09UX-F70MD[UB]_f 01.7.10, 2:56 PM9
– 10 –
English
Basic and Common Operations
The buttons emphasized in the illustration below are used and explained in this section (pages 11 to 13.)
Remote control
Main unit (Top view)
FM MODE
10
COLOR
MD GROUP
MD TITLE
INPUT/EDIT
CLOCK
/TIMER
DISPLAY
/CHARA
MD TITLE
SEARCH
SOUND
MODE
AHB
PRO
SET
CANCEL
CD
DIMMER
1 2 3
ENTER
FM/AM
/AUX
REV.MODE
REPEAT
TAPE
STANDBY/ON
SLEEP
PLAY MODE
MARK
BEEP
VOLUME
MD
4 5 6
7 8 9
10
0
+
10
RM-SUXF70MDU
STANDBY/ON
COLOR DIMMER
SET
10
0
+
10
SOUND
MODE
AHB
PRO
CD
FM/AM
/AUX
TAPE
BEEP
VOLUME
MD
F M / A M
open/close
STANDBY/ON COLOR
AUX
VOLUME
MODE
select
MD GROUP
REC MODE
TAPE
M DC D open/close
REC
start
Main unit (Front view)
PHONES
STANDBY/ON
COMPACT
DIGITAL AUDIO
Continued
EN10-13UX-F70MD[UB]_f 01.7.10, 2:57 PM10
– 11 –
English
Turning On the Power
When you press the play buttons (CD 3 / 8, MD 3 / 8,
TAPE 2 3) for a particular source or the FM/AM/AUX
button (or FM/AM or AUX button on the main unit), the
unit automatically turns on (and starts playback if the
source is ready).
To turn on the unit without playing, press
STANDBY/ON.
The STANDBY/ON lamp on the electronic swing panel
lights green.
To turn off the unit (on standby), press
STANDBY/ON again.
The STANDBY/ON lamp on the electronic swing panel
lights red.
“0:00” appears on the display until you set the
built-in clock. After setting the clock, the clock time will
appear on the display while the unit is turned off (on
standby.)
A little power is always consumed even while the unit is
on standby.
To set the built-in clock, see page 57.
To switch off the power supply completely, unplug the
AC power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
The clock setting, the tuner preset stations and other settings will
be erased.
Selecting the Sources and Starting Play
To select the tuner or external equipment, press
FM/AM/AUX.
The unit automatically turns on (when the unit is on
standby) and the last selected source appears on the display.
Each time you press the button, the sources change as
follows:
When you change the source from the others, “TUNER”
appears for a while.
For more detailed tuner operations, see pages 14 to 16.
For operating the external equipment, see the manuals
supplied with them.
When using the main unit:
Press FM/AM to select the tuner.
– Each time you press the button, the band alternates
between FM and AM.
Press AUX to select the external equipment.
To select the CD player, press CD 3 / 8.
The unit automatically turns on (when the unit is on
standby), and “CD” appears on the display. Play will start if
a CD is on the disc tray. (“NO DISC” will appear on the
display if a CD is not loaded.)
To stop playback, press 7.
For more detailed operations, see pages 17 to 21.
To select the MD player, press MD 3 / 8.
The unit automatically turns on (when the unit is on
standby), and “MD” appears on the display. Play will start
if an MD is in the MD loading slot. (“NO DISC” will
appear on the display if an MD is not loaded.)
To stop playback, press 7.
For more detailed operations, see pages 22 to 26.
To select the tape, press TAPE 2 3.
The unit automatically turns on (when the unit is on
standby), and “TAPE” appears on the display. Play will
start if a tape is in the cassette holder. (“NO TAPE” will
appear on the display if a tape is not in the cassette holder.)
To stop playback, press 7.
For more detailed operations, see pages 27 and 28.
FM AM
AUX
(TUNER)
EN10-13UX-F70MD[UB]_f 01.7.10, 2:57 PM11
– 12 –
English
Adjusting the Volume
You can adjust the volume level only while the unit is
turned on. The volume level has no effect on recording.
To increase the volume, press VOLUME + .
To decrease the volume, press VOLUME – .
The volume level meter appears on the display.
The volume level can be adjusted in 41 steps (VOL MIN,
VOL 1 – VOL 39, and VOL MAX.)
When pressing and holding the button, you can change
the volume level continuously.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers. Be sure to turn down the volume before
connecting or putting on the headphones.
If “CANNOT LISTEN!” appears on the display
During high-speed recording (see page 31), you cannot listen to
any source, and therefore, cannot adjust the volume level.
DO NOT turn off (on standby) the unit with the
volume set to an extremely high level; otherwise, the
sudden blast of sound can damage your hearing,
speakers and/or headphones when you turn on the
unit or start playing any source.
REMEMBER you cannot adjust the volume level
while the unit is in standby mode.
Reinforcing the Bass Sound
The richness and fullness of the bass sound is clearly
maintained regardless of how low you set the volume —
Active Hyper Bass Pro. The AHB PRO effect can be
applied only to playback sounds, and cannot be used for
recording.
On the remote control ONLY:
To get the effect, press AHB PRO.
The AHB PRO indicator lights on the display.
Each time you press the button, the effect changes as
follows:
AHB 1: Bass sound is clearly heard even in the low
volume.
AHB 2: More richness and fullness of the bass sound
is heard.
AHB OFF: Cancels the AHB PRO effect.
The AHB PRO indicator goes off from the
display.
T
o check the AHB PRO setting currently selected, press
AHB PRO once while the AHB PRO indicator is lit.
Selecting the Sound Modes
You can select one of the 4 preset sound modes. The sound
modes can be applied only to playback sounds, and cannot
be used for recording.
On the remote control ONLY:
To select the sound modes, press SOUND MODE
repeatedly until the sound mode you want appears on the
display.
The SOUND indicator also lights on the display.
Each time you press the button, the sound mode changes
as follows:
ROCK: Boosts low and high frequency.
Good for acoustic music.
POP: Good for vocal music or voice.
CLASSIC: Good for classical music.
JAZZ: Good for jazz music.
FLAT: Cancels the sound mode.
The SOUND indicator goes off from the
display.
To check the sound mode currently selected, press
SOUND MODE once while the SOUND indicator is lit.
(Maximum)
(Minimum)
ROCK POP
CLASSIC
JAZZ
FLAT
(Canceled)
AHB 1 AHB 2
AHB OFF
(Canceled)
Turning On/Off the Key-touch Tone
You can deactivate the key-touch tone if you do not want it
to beep each time you press the button.
On the remote control ONLY:
Press BEEP.
Each time you press the button, the key-touch tone turns
on (BEEP ON) and off (BEEP OFF) alternately:
BEEP ON BEEP OFF
Continued
EN10-13UX-F70MD[UB]_f 01.7.10, 2:57 PM12
– 13 –
English
Setting the Display Illumination
You can change the color and brightness of the display
illumination.
To select the color pattern
You can select the color pattern by your preference.
If you press COLOR while the unit is turned off, the
display illumination will start (see page 9.)
While the unit is turned on, press COLOR repeatedly
until the color pattern you want appears on the display.
• Each time you press the button, the color pattern changes
as follows:
COLOR RANDOM: Changes the illumination color
randomly every 2 seconds.
COLOR GRADATION:
Changes the illumination color
gradually.
TODAY’S COLOR #* DAILY:
Changes the illumination color
every day. You can select which
color to be started with. (See “To
set TODAY’S COLOR” to the
right.)
* The color number of TODAY’S COLOR is selected
from COLOR 1 – 7.
COLOR 1 – 7: You can adjust and register the
color from COLOR 1 to 7. (See
“To adjust and register the color”
to the right.)
More on the display illumination
The colors shown on the display cannot always be reproduced
precisely. Due to the circumstances (room temperature, etc.)
where the unit is used, colors may vary slightly.
When you change the color of the display, the display may seem
to move back and forth; this is a characteristic of this unit and is
not a malfunction.
When a strong light strikes the display, the display happens to
become dark, but this is not a malfunction.
To adjust and register the color
You can adjust the color by changing the tone, whiteness,
brigtness, and register into COLOR 1 to 7.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.
On the remote control ONLY:
1
Press COLOR repeatedly until the color number
(COLOR 1 to 7) you want to adjust appears on the
display.
The adjustment bars appear on the display.
2
Adjust the tone, whiteness and brightness.
1) Press = or + to select the level you want and
press SET.
Each time you press SET, the adjustment items
change.
The tone can be adjusted in 14 patterns. The
whiteness can be adjusted in 3 levels and the
brightness can be adjusted in 2 levels.
2) Repeat step 1 to adjust “WHITENESS” and
“BRIGHTNESS.
If the whiteness is set to the right end, the tone
you adjusted will be no longer valid.
To set “TODAY’S COLOR”
The illumination color changes automatically each time the
built-in clock becomes “0:00.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.
On the remote control ONLY:
1
Press COLOR repeatedly until “TODAY’S
COLOR” appears on the display.
2
Press = and + to select the color number (COLOR
1 to 7.)
To dim the display
This function can be used only while the unit is turned on.
On the remote control ONLY:
To dim the display, press DIMMER.
To brighten the display, press DIMMER again.
Press COLOR also brightens the display.
*
COLOR
GRADATION
COLOR
RANDOM
TODAY’S
COLOR #
DAILY
COLOR 1
– COLOR 7
EN10-13UX-F70MD[UB]_f 01.7.10, 2:57 PM13
– 14 –
English
Listening to FM and AM Broadcasts
Remote control
Main unit (Top view)
The buttons emphasized in the illustration below are used and explained in this section (pages 15 and 16.)
FM MODE
10
COLOR
MD GROUP
MD TITLE
INPUT/EDIT
CLOCK
/TIMER
DISPLAY
/CHARA
MD TITLE
SEARCH
SOUND
MODE
AHB
PRO
SET
CANCEL
CD
DIMMER
1 2 3
ENTER
FM/AM
/AUX
REV.MODE
REPEAT
TAPE
STANDBY/ON
SLEEP
PLAY MODE
MARK
BEEP
VOLUME
MD
4 5 6
7 8 9
10
0
+
10
RM-SUXF70MDU
SET
FM/AM
/AUX
FM MODE
DISPLAY
/CHARA
1 2 3
4 5 6
7 8 9
10
0
+
10
F M / A M
STANDBY/ON
COLOR
AUX
VOLUME
MODE
select
MD GROUP
REC MODE
TAPE
M D open/close
REC
start
open/close C D
Continued
EN14-16UX-F70MD[UB]_f 01.7.10, 2:57 PM14
– 15 –
English
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and some
countries use 10 kHz spacing.
When shipped, the built-in AM tuner is set to 9 kHz
spacing. You can change it to 9 kHz or 10 kHz spacing.
On the main unit ONLY:
To set the AM tuner to the 10 kHz spacing, be sure that
the unit is turned off, but is plugged into a wall outlet.
While holding ¢, press
STANDBY/ON. The unit
turns on and “AM 10 kHz” appears on the display for a
while.
To set it back to the 9 kHz spacing, be sure that the unit is
turned off, but is plugged into a wall outlet.
While holding 4, press
STANDBY/ON. The unit
turns on and “AM 9 kHz” appears on the display for a
while.
Tuning in a Station
1
Press FM/AM/AUX (or FM/AM on the main unit)
repeatedly to select “FM” or “AM.
The unit automatically turns on with the last source
selected.
Each time you press the button, the source changes as
follows:
2
Press and hold ¢ or 4 until the station
frequencies start changing continuously on the
display.
¢ : to increase the frequencies.
4 : to decrease the frequencies.
The unit starts searching stations and stops when a
station of sufficient signal strength is tuned in.
• If an FM program is broadcast in stereo, the ST
(stereo) indicator lights on the display.
To stop during searching, press ¢ or 4.
When you repeatedly press ¢ or 4
The frequency changes step by step.
To change the FM reception mode
When an FM stereo broadcast is noisy or hard to receive,
you can change the FM reception mode to improve the
reception.
On the remote control ONLY:
Press FM MODE so that the MONO indicator lights on
the display.
Each time you press the button, MONO indicator lights
and goes off alternately.
When the MONO indicator is lit:
Reception improves though stereo effect is lost.
When the MONO indicator is not lit:
You can hear stereo sound when a program is
broadcast in stereo.
The ST indicator lights while receiving the FM
stereo broadcast.
In addition, static noise between stations will be
erased while tuning.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
In some cases, test frequencies have been already memorized
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You can
preset the stations you want into memory by following the
presetting method.
There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step
2
again.
On the remote control ONLY:
1
Tune in a station you want to preset.
See “Tuning in a Station” to the left.
2
Press SET.
The preset number starts flashing as follows:
When you select an FM station in step
1
When you select an AM station in step
1
Ex. An FM station is tuned in.
FM AM
AUX
(TUNER)
Preset No. 1 alway appears at first.
When using the
remote control:
When using the
main unit:
FM AM
(TUNER)
EN14-16UX-F70MD[UB]_f 01.7.10, 2:57 PM15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

JVC UX-F72MD User manual

Category
CD players
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI