Epson perfection 4990 Product information

Brand: Epson

Model: perfection 4990

Category: Print & Scan

Type: Product information

Page

1 of 2

PSB.2007.04.001

EPSON

Product Support Bulletin

Date: April 2, 2007 Originator: VS

PSB #: PSB.2007.04.001 Authorization:

Reference: TI 06-0491 Rev.B Total Pages: 2

Product(s): Expression 10000XL/1640 XL/1680/1600/800/836 XL, Perfection

3490/3590/4490/V700/V750/V100/V350/1240U/1250/1260/1640/1650/1660/

1670/2400/2480/2580/3170/3200/4180/4870/4990/640U/1200U/610, GT-

2500/15000/30000 series scanners

Subject: Scanning Application Force Quits on Mac OS 10.4

This bulletin was created to inform you of an error that may occur when opening a TWAIN-

compliant scanning application on a Macintosh computer running OS 10.4.

Description of Problem:

When launching a Twain-compliant scanning application after deleting your Epson Scan driver

with an Epson Scan uninstaller not compatible with your scanner model, the application will

force quit during start-up. For example, using a Perfection 4490 driver uninstaller to delete a

Perfection 3490 driver will cause your scanning application to suddenly close during start-up.

This issue affects the following TWAIN-compliant applications:

EPSON Creativity Suite When pressing the Scan button, the Scan

Assistant force quits

Copy Utility Force quits during start-up

Photo Impression Force quits during start-up

Photoshop Elements Force quits during start-up

Photoshop Force quits during start-up

Photoshop CS2 Force quits during start-up

This issue can also occur under the following conditions:

1) Dragging the Epson Scan folder (located in the Applications folder) to the Trash can

2) Upgrading your scanner and using the Epson Scan driver from the new scanner to

delete the driver from the older scanner, and then installing the new driver

Operating Systems Effected:

Mac OS 10.4 to 10.4.9

Affected Epson Scan Driver Versions:

2.70A or later

Page

2 of 2

PSB.2007.04.001

Correct Procedure for Deleting Epson Scan Driver:

! Use the driver specifically written for your scanner model to uninstall the Epson Scan

driver.

! If you have more than one Epson scanner model on your computer, use the driver

specifically written for each scanner to uninstall its respective device driver.

! If upgrading from a Power PC-based Epson Scan driver to a Universal Binary driver,

first delete the Power PC driver using only the Power PC driver for your scanner model.

Then install the Universal Binary driver.

If the above procedure does not resolve the problem, then manually verify that the Epson

Scan files and folders, listed below, have been deleted.

! EPSON Scan (in Applications Folder)

! EPSON*********.ds (****** = scanner model)---located in the Library / Image Capture /

TWAIN Data Sources folder

Page 1 of 1

EPSON PRODUCT SUPPORT BULLETIN

Date:

2/2/2004

Originator:

PSB #:

PSB.2004.02.004

Authorization:

/DS

Reference:

TE03-389 Rev. A

Total Pages:

Product(s):

Expression 1600/1680/1640XL Series Scanners; Perfection

610/640/1200/1240/1250/1260/1640/1650/1660/1670/2400/2450/3170/3200

Series Scanners; Stylus CX5200/CX3200/CX5400 All-in-One Products

Subject:

EPSON Scan TWAIN Ver. 1.28 for Mac OS 10.2 to 10.3

This bulletin was created to inform you of an updated Epson Scan Twain Driver (1.28A) for the

following models: Perfection 610/640/1200/1240/1250/1260/1640/

1650/1660/1670/2400/2450/3170/3200 series scanners, Stylus CX3200/CX5200/CX5400

multi-function devices, Expression 1600/1680/1640XL series scanners.

Reason:

The new Epson Scan driver improves functionality when scanning in Mac OS 10.3. See the

next section for the list of changes included in the new driver.

Driver Improvements:

• Enables Epson Scan to start when the Scan button is pushed.

• Enables Epson Scan to start even if the volume name (Hard Disk) on the desktop is

only 2 bytes (2 characters) in length.

• Eliminates the error “Epson scan cannot be started”, which occurs when the USB

cable is disconnected while Epson scan is loading.

• Corrects lock-up issues when using the Zoom tool in Epson Scan.

• Corrects functionality issues and mouse cursor lock-ups when using the Histogram

Adjustment, Tone Correction and Image Adjustment tools or when clicking on each

tool’s Title bar.

• Prevents Epson Scan from unexpectedly quitting when scanning two or more times

from PhotoShop with a Perfection 1250 scanner.

• Prevents Epson Scan from locking up when scanning from a Perfection 3200

scanner with a Firewire connection.

• Prevents Epson Scan from unexpectedly quitting when removing the Firewire cable

from a Perfection 3200 scanner while Epson Scan is open.

• Prevents the Epson Scan Utility from freezing when using the Perfection 1250 or

1260 scanner.

• Enables Epson Scan to launch properly when scanning from an Expression 1680/ or

1640XL with a Firewire connection.

Page 2 of 2

Limitations of new driver:

• This driver does not support “Fast User Switching” in OS 10.3. This feature must be

turned off before using Epson Scan.

• You may receive an error “Epson Scan cannot be started” when trying to scan from

a Perfection 2450 that is connected to a USB 2.0 supported port. To avoid this error,

use a Firewire connection or a USB 1.1 only supported port.

• Not all the scanner models on this list support Color Restoration and Dust Removal

so these settings may be unavailable in Epson Scan.

• If experiencing unstable operation when scanning from a Perfection 1250 or 1260

scanner, restart your system.

• If the computer goes into “sleep mode” and this setting was enabled in the Apple

Menu and you try to switch to a different mode after doing a preview scan in

Photoshop, the Epson Scan driver will freeze. This does not happen if the computer

goes into “sleep mode” after screen saver has started. To avoid lock-ups, change

the scanning mode before the computer goes into “sleep mode” or re-launch Epson

Scan after the computer wakes up and then change modes.

• After scanning with the Perfection 1250, if you then close Epson Scan and

disconnect the USB cable, a scanner model selection dialog box may appear on the

screen. Click “No” and the box closes. You can scan normally afterwards.

Action:

The new driver is available on the Epson web site. Go to www.epson.com and click on Drivers

& Downloads. Select your scanner model. On the Downloads page look for TWAIN Driver and

Epson Scan Utility v.1.28A in the Macintosh section.

To Install Epson Scan 1.28A:

1. Launch the EPSON Scan Installer and follow the on screen instructions.

2. After the TWAIN has been installed, connect the USB or Firewire interface cable from the

scanner to the computer.

To Uninstall Epson Scan 1.28A:

1. Disconnect the USB interface cable from the scanner.

2. Launch the EPSON Scan Installer.

3. Open the drop-down menu where you see “Easy Install” and select “Uninstall”.

4. Click the Uninstall button.

Page

1 of 3

EPSON

Product Support Bulletin

Date:

04/30/2003

Originator:

PSB #:

PSB.2003.05.008

Authorization:

Reference:

N/A

Total Pages:

Product(s):

Perfection 1240/1250/1640/1650/1260/1660/2400/2450

Subject:

Installing Smart Panel on a drive other than “C:”

This bulletin was created to inform you of a procedure for installing Smart Panel on drives

other than “C:”.

Description:

Smart Panel will install on Drive C: by default. The procedure for specifying a different drive

isn’t immediately apparent.

Solution:

The following steps will allow most of Smart Panel to install on a different drive letter other

than the default. The Epson Twain and Scan to Web programs will only install on drive C:\.

01) Using "Auto Run" let the installation start, then "Cancel" the installation at the program

selection screen.

02) Using Windows Explorer, locate the Epson CD, open the "Installers" folder

03) Open the "SPANEL" folder found in the Installers folder

03) Open the "American" folder found in the “SPANEL” folder, and double-click on the "Setup"

file with the "Monitor/computer" icon

04) Advance through the "Agreement" screens

05) At the "Choose Designation Location" screen click on "Browse" (See example on next

page)

Page

2 of 3

Page

3 of 3

06) Click on the "Path Line" and using the back arrow back up the cursor to the drive letter and

change it to the desired "drive" letter.

07) Click on "OK"

08) For the message to create the necessary folders, click "YES"

09) Click "Next"

10) Continue with "installation"

11) Follow steps 5 through 9 for "Copy Utility" installation

12) Follow steps 5 through 9 for any other Smart Panel applet to be installed

13) If Epson Twain has not been installed, go to "Twain 5.x" and run disk 1

14) Restart system and test the software with the scanner

Page 1 of 1

EPSON

RODUCT

UPPORT

ULLETIN

Date:

4/30/2003

Originator:

PSB #:

PSB.2003.05.006

Authorization:

Reference:

N/A

Total Pages:

Product(s):

Perfection 1240/1250/1640/1650/1260/1660/2400/2450

Subject:

Making Adjustments in Epson Twain 5.X.X

This bulletin was created to inform you of a procedure for making adjustments in Epson Twain

5.X.X

Description:

01) When using the TPU (transparency adapter) in manual mode or auto mode the

scanned image is not correctly detected.

02) The scanned TPU image has a color cast to it.

Solution:

01) If Epson twain is in full auto mode:

a) Click “Cancel” and then “Manual” to get into manual mode.

b) Click on the “Configuration tab”

c) Remove the check mark or dot from “Auto Thumbnail” option.

i. This will allow “manual” selection for the TPU type of film.

ii. This will allow “manual” marquees.

02) If the scanned TPU image has a color cast:

a) Marquee the image making sure none of the border of the film strip/slide is

included.

b) Do a magnified preview of the marquee to verify border.

c) Using the “tools” bar (color wheel, wench and screwdriver) make final

adjustments to the image.

i. Click on “Settings” and clear “User Defined” and give these settings a

name (e.g. “positive film”).

ii. When scanning similar images in the future, this new color correction can

be selected from the “Settings” option.

Page 1 of 1

EPSON

RODUCT

UPPORT

ULLETIN

Date:

05/08/2003

Originator:

PSB #:

2003.05.003

Authorization:

Reference:

N/A

Total Pages:

Product(s):

Perfection 610/640/1240U/1640SU/1250/1650/1260/1660/2400/2450, Stylus

CX3200 and Stylus CX5200

Subject:

Epson TWAIN v. 5.75A for Apple Macintosh OS X 10.2 and Image Capture

This bulletin was created to inform you of an issue that can occur when using the Epson TWAIN

driver (v. 5.75A) in Apple’s Image Capture utility on a Macintosh computer running OS X v.10.2

to v.10.2.4.

Reason:

After completing a scan with the Epson TWAIN driver, Image Capture may suddenly crash. The

problem appears to be isolated to Image Capture and does NOT occur in Adobe Photoshop 7,

Photoshop Elements 2.0 or other TWAIN-compliant applications.

Note:

“Image Capture” and “Preview” are stand-alone application utilities built into OS X.

Steps to Reproduce:

1. Launch Image Capture. Open Preferences, Under "Scanner Preferences" check the box for

"Use TWAIN software whenever possible".

2. Quit Image Capture to save the setting.

3. Re-launch Image Capture.

4. Click Scan.

5. Click Cancel in the Epson TWAIN Full-Auto mode window.

6. Click “Manual Mode” to change to the Epson TWAIN Manual mode user interface window.

7. Without making a selection in the preview window, click the “Scan” button in the TWAIN

window, and wait for the scan to complete.

Note:

After acquiring an image, Image Capture automatically opens the “Preview” application to

view the image.

8. Notice that Image Capture crashes after sending the resulting scanned image to the

“Preview” application.

Solution and Workarounds:

Choose from any of the solutions listed below.

1. In the Preferences settings for Image Capture, do NOT check the box for "Use TWAIN

software whenever possible".

2. If using the Epson TWAIN in Manual mode, drag a selection box around the area you

want to scan in the preview window before scanning.

3. Use Adobe Photoshop 7, Photoshop Elements 2.0 or other TWAIN-compliant

applications instead of Image Capture.

4. Upgrade your MAC OS X to 10.2.5 or higher.

Page 1 of 2

EPSON PRODUCT SUPPORT BULLETIN

Date:

04/01/2003

Originator:

PSB #:

PSB.2003.04.003

Authorization:

Reference:

N/A

Total Pages:

Product(s):

All EPSON Scanners

Subject:

Windows™ and Macintosh® Operating System requirements for USB 1.1/2.0

and IEEE-1394/FireWire® Interface connectivity

This bulletin was created to inform customers of EPSON America’s support policy regarding

Windows™ and Macintosh® operating system requirements for USB 1.1/2.0 and IEEE-

1394/FireWire® interface connectivity.

Reason:

Currently, there are many add-in USB 2.0 and IEEE-1394 connection host adapter products on the

market that include drivers for Windows and Macintosh OS that did not originally support specific

interfaces. Epson has released several scanner products with built-in USB 2.0 and/or IEEE-1394

(FireWire) ports. This document provides a guideline on EPSON America’s support policy on the

various operating systems and the interface connections they support. EPSON technical support

representatives will only be able to support customers who have Epson products that are configured

in accordance with the operating system requirements outlined here and in the product’s

documentation. Epson customers experiencing problems on an Epson product connected to an add-

in USB 2.0 or IEEE-1394 interface that does not meet the minimum system requirements will be

asked to contact the interface product vendor or computer manufacturer for technical support.

This document is not model specific. It does not include other important system requirements

required to determine product compatibility on a user’s computer. To determine product support

compatibility, please refer to the specific scanner’s minimum system requirements found on the

outside of the product box, or visit Epson’s web site at www.epson.com.

The guidelines below were compiled from Microsoft’s and Apple’s Support websites and their

published system requirements for supported interface connectivity. For more information on

Windows and Macintosh Interface support please refer to Microsoft’s online Knowledge base at

www.microsoft.com

or Apple’s web site at www.apple.com. For information on add-in 3

party

interface products please refer to the vendor’s documentation or product support web site.

Windows

USB 1.1:

Full version Microsoft Windows 98/98 Second Edition, Windows Me, Windows 2000 or

Windows XP or Upgrade from a full version of Windows 98/98SE, Me, 2000

IEEE-1394 (FireWire):

Full versions of Windows Me/2000/XP, or upgrade from a full version of

Windows 98/98SE. Host computer must have an OHCI compliant IEEE-1394-1995 card or port

installed.

USB 2.0 Hi-Speed

: Full versions of Windows XP or upgrade from a full version of Windows 98/98SE,

Me, 2000. Host computer must have an EHCI compliant USB 2.0 Hi-Speed card or port installed.

Page 2 of 2

Windows 2000 did not support the USB 2.0 hardware specification at the time it was first released.

Refer to Microsoft Knowledge Base Article - 319973 Universal Serial Bus 2.0 Support in Windows

2000 for more information.

Important Notes:

1.) Operating system must not be an upgrade from Windows 95.

2.) For Windows 2000 or XP you must be logged in as an administrator or as a user with

administrator rights before you can install and use EPSON software.

3.) USB hubs must be self-powered and connected in a first-tier configuration for reliability

Macintosh OS

USB 1.1: Apple Macintosh computer (G3, G4, or iMac) with built-in USB port, running Mac® OS 8.5.1

to 9.2.2 with all USB extensions enabled. For OS X, you must have 10.1.3 or later.

FireWire (IEEE 1394):

Power PC-equipped Macintosh or newer with Mac OS 8.6 to 9.2.2 with Apple’s

FireWire 2.1 (or later) software installed. For OS X, you must have 10.1.3 or later.

USB 2.0 Hi-Speed

: Not supported

Important Notes:

1.) You cannot use a serial interface to connect the scanner.

2.) Interface adapter cables (i.e. SCSI to USB, or USB to Serial, etc) are not supported.

3.) USB hubs must be self-powered and connected in a first-tier configuration for reliability.

4.) FireWire port must be compliant with this specification: IEEE 1394-2000 compatible.

Page 1 of 2

EPSON PRODUCT SUPPORT BULLETIN

Date:

04/1/2003

Originator:

PSB #:

PSB.2003.04.001

Authorization:

Reference:

N/A

Total Pages:

Product(s):

Perfection 640U/1240U/1250/1640SU/1650/2450/1260/1660/2400/3200

Series Scanners and the Stylus CX 3200/5200 all-in-one series

Subject:

Smart Panel Copy Utility may produce copies with a light gray/blue/pink

background when printing to non-EPSON printers.

Description of issue

If you are using Copy from EPSON Smart Panel 2.5/2.6 or you installed the Copy utility 2.00A

patch for Smart Panel 2.0A/1.0.xA, you may find that the program produces copies with a light

gray/blue/pink background.

Reason

This is because when printing to non-EPSON printers with the Copy utility, the Automatic

Document Enhancement feature is turned off by default.

Solution:

To remove the background, you must enable Automatic Document Enhancement. To turn on

this feature, launch the Copy applet by double-clicking on its icon. Select Epson TWAIN 5 at

the following window and click “OK”.

Page 2 of 2

Click on the “Image Adjust” button. You will notice the Auto Document Enhancement OFF

button is selected (highlighted in dark gray).

Click the ON button. You will now notice that this button is selected (highlighted in dark gray).

Now click on the large green Copy button, your image will be scanned and printed. The copy

of your document should look very close to the original with no background colors added.

Note: The Copy utility was designed to scan and print a copy of a Letter size (8.5” X 11”)

document. If your document is not a full letter-size piece of paper, then the portion of the

scanner’s document mat that is showing will be included as part of your copy. Some bright

white papers can cause a noticeable contrast between the document and the document mat.

As a result the Copy utility may recognize the exposed document mat as a having a light blue

color. In this case you may still see a light blue background on your printout where the

document mat was showing.

Page 1 of 1

EPSON

RODUCT

UPPORT

ULLETIN

Date:

9/20/2002

Originator:

TC/JD

PSB #:

PSB.2002.04.002B

Authorization:

Reference:

N/A

Total Pages:

Product(s):

Perfection 640U, 1240U, 1640SU, 1250, 1650, 2450 series scanners

Subject:

Epson Smart Panel & Security Rights on Windows 2000

This bulletin was created to inform you of an issue with Epson Smart Panel running under

Windows 2000. This issue affects Smart Panel version 1.0.xA (1.01, 1.02, 1.03), bundled with

the Perfection 640U/1240U/1640SU series and version 2.0A, which is included with the

Perfection 1250/1650/2450 series.

Description of the Issue:

When running Windows 2000, if Epson Smart Panel is installed from the scanner software

CD, and is used by members of the Administrator or Power Users Group, the program works

normally. If a member of a restricted group (Users, Backup Operators, Replicator, Guest) logs

on to a computer on which an Administrator or Power User installed Smart Panel, the user will

receive an error when booting up to the desktop. A dialog box with an “OK” button pops up

displaying the following error message:

“There is no Registry data for EPSON SMART PANEL!"

Clicking "OK" in the dialog box does not remove the error message, even if you click OK

repeatedly. The computer is unusable at this point and eventually locks up. To recover, the

user must perform a hard reset and log in as a Power user or Administrator.

If a member of the “Restricted User” group attempts to install the Epson Smart Panel software,

one of two things happens: (1) Windows prevents the user from starting installation or (2) the

installation completes and all users, including Administrators and Power Users will see the

"Registry Data Error" when booting to the desktop.

Reason:

Smart Panel loads “Start” button monitoring during Windows startup. When logged in as a

restricted user, Windows returns an error message as described above because the user has

insufficient rights. Specifications for Smart Panel do not provide sufficient rights for restricted

users to install and use Smart Panel on Windows 2000. Only Administrators, users with

Administrator rights and Power users have sufficient access privileges to install and use Smart

Panel. If a member of a Restricted user group is able to install Epson Smart Panel, the

program will need to be manually removed by an Administrator logged on in “Safe Mode.”

Using the “Search” utility in Windows 2000, delete all files for “Epson Smart Panel for

Scanners.” A System Administrator will then need to add the "Restricted user” to the Power

Users Group before the user can install and use Smart Panel.

EPSON

RODUCT

UPPORT

ULLETIN

Date:

9/6/2002

Originator:

PSB #:

PSB.2002.02.003R1

Authorization:

Reference:

N/A

Total Pages:

Product(s):

Perfection 640U, 1240, 1640, 1250, 1650, 2450, 1260, 1660, 2400 series

scanners

Subject:

Copy Utility Workaround for Non-Epson Printers

This bulletin was created to provide information on using Smart Panel’s Copy Utility with non-Epson

printers in Windows. The following sections describe a workaround that can be used when Copy Utility

has problems working with non-Epson printers.

Description of Issue:

Epson Smart Panel includes a utility called Copy that is used for scanning and printing documents.

Although Copy works with non-Epson printers it does not support all models. Epson periodically releases

updates to support the newer models. However, since new printers are continually being released to

market, the current Copy update may not work with the latest models.

When Copy Utility launches, it first initializes the scanner and printer. If it does not recognize the printer,

the program will normally return an error. The error message may vary depending on the operating

system and version of Copy. In some cases, the program won’t generate an error dialog; instead, it will

launch and then quickly shut down. If you get the error dialog, it will typically look like one of those listed

below. When you click OK to close the dialog, the program takes you back to the Smart Panel main user

interface.

Workaround:

As a temporary solution, select another Windows default printer (i.e. one that’s compatible with Copy)

and then launch Copy. In Copy, change the printer back to the one that you want to use. Click the green

and Copy button to scan and print.

Follow these steps to configure Copy for the workaround.

1) First, verify that you have installed the latest version of Copy (currently 2.00A). Launch Copy and

look for a green screen. This is version 2.00A and it should look like this:

If you don’t see this on your screen then visit our web site at www.epson.com and download the Copy

update.

2) Once you have installed the update, test your printer in Copy. If you get an error then go to the

next step.

3) Click the Start button and then click Settings. Select Printers. You can also use Control Panel to

select Printers (Printers and Faxes for Windows XP). In Printers, use the Add Printer Wizard to

add a printer. For Windows 98 and up, you can try the HP LaserJet 4. For Windows 2000 and

XP, the Stylus Photo 750 ESC/P2 works fine. For Windows 95, you’ll need to use an older model

such as the HP LaserJet 3 series. Keep in mind that other models can be used. If one model

doesn’t work then use another one.

4) Follow the on-screen instructions to install the printer. Once completed verify that it is the default

printer.

5) Launch Copy. If the new default printer is compatible, the program will open normally.

6) Click the Device Settings button. This will bring up the Device Settings user interface. In the

Output Device field (the default printer will be listed here), click on the arrow. This will bring up

the Output Device Chooser window. The screen should look like this.

7) Change the printer name to the one you want to use and then click OK. Click on the Green

button to start scanning.

EPSON

RODUCT

UPPORT

ULLETIN

Date: 9/25/01

PSB No.:

PSB.2001.09.006R3

Reference: N/A

Originator: TC

Authorization:

Affected Product(s): EPSON Perfection 640U/1240U/1640SU & 1250/1650/2450 Series Scanners

Subject: Updated Photo Print Utility Version 1.31A for EPSON Smart Panel v.1.0xA & 2.0A for Windows

This bulletin provides information on the latest release of the Epson Smart Panel - Photo Print Utility program, ver. 1.31A. This

version of the Photo Print Utility works with the following scanner products and it provides improved compatibility and functionality

with Windows Operating Systems and some non-Epson printers. *

Perfection 640 Perfection 1240U Perfection 1250/1250 Photo

Perfection 1240U Photo Perfection 1640SU Perfection 1650/1650 Photo

Perfection 1640SU Photo Perfection 1640SU Office Perfection 2450 Photo

Note: Epson and other printer vendors continually release new models into the market. If your printer does not work with the updated

Photo Print Utility, please check the Epson web site for updates.

Photo Print can be downloaded from Epson’s web site. From your browser, enter this URL:

http://support.epson.com/filelibrary.html

On the Downloads page, click on Perfection Series. Click on your scanner model.

On the Downloads page click on the Photo Print Utility program and follow the on-screen instructions to complete the download.

Installation Instructions:

Use these steps to install the updated Photo Print Utility.

1. Close Smart Panel if you have it running.

2. From the Start button click

Run

and then

Browse

3. Search for the folder that contains the downloaded Photo Print Utility file (By default this folder is called EPSON, unless you

specified a different download folder location).

4. Double-click this file to extract the Setup files.

5. Double-click SETUP.EXE. The installation will start and the Welcome screen will launch. Click Next.

6. Next you will see the following screen, click Browse.

Note:

You must install the update files in the same directory as the original version of Photo Print in order for the update to work

correctly. If your installation of EPSON Smart Panel was performed using the default directory you need to install the files to the

following location on your Hard Drive

C:\Program Files\Epson\EPSON Smart Panel for Scanners\Photo Print Utility

. If you did

not install the program using the default location you will need to install the Update files to the directory in which you installed

EPSON Smart Panel's Photo Print Utility.

7. Browse to the following location: "C:\program files\epson\epson smart panel for scanners\photo print utility” and click OK

8. If you are pointing to the correct folder, you will see the following screen. Click Next. If you do not see the screen below, go

back to step 6.

Note

: the full path to the destination folder may not be showing.

9. You will see a Setup Complete window, click Finish to complete the install.

10. To verify you have properly installed the update open Epson Smart Panel and click on the Photo Print Button. You will see a

progress window that says "Setting up printer." Before you print, have your media type, print size, and Printer Driver set to

the correct settings. Put a photo on the document glass and Click the "Print" button. The "Select TWAIN source" window will

pop up, select "EPSON TWAIN 5" and click OK. Your photo will be scanned and printed.

Note

: You can launch EPSON Photo Print as a standalone application, without needing to launch Epson Smart Panel. The Photo Print

Utility update program will automatically put an Entry in the Start menu. To find this entry click on; Start>Programs>EPSON

Scanner>EPSON Photo Print. The update program will also put an “EPSON Photo Print” shortcut icon on your Desktop, you can

launch the Photo Print Utility from the shortcut. If you do not want this icon on the desktop, simply drag it to the Recycle Bin or

highlight the shortcut icon and hit the delete key on your keyboard.

Page is loading ...

Epson perfection 4990 Product information

Epson perfection 4990 Product information

Epson perfection 4990 Product information

Related papers

Other documents