Roland MDS-Compact Owner's manual

Type
Owner's manual

This manual is also suitable for

5.
Attaching the pad mounts
The tips of the mounts are sharp. Handle them with care.
5–1. Place the stand upright, then loosen the hand knobs
of holders A and “B” (two places). Next, spread open
the pipes at left and right.
5–2. Verify that the four vertical pipes are truly vertical.
If the stand wobbles, loosen the bolts on the
holders of curved pipes “L and “R, and adjust the
height. After adjusting the height, tighten the
bolts on the holders.
Hand knobs
Holder bolts
5–3. Attach mount holders to the top of the stand and
tighten the respective hand knobs.
Mount holder
Mount holder
77
Hand knobs
5–4. Attach the pad mounts to mount holder, and rmly
tighten the respective hand knobs.
Pad mount
Hand knobs
8
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES. After reading, keep the document(s)
where it will be available for immediate reference.
Roland and V-Drums are registered trademarks of Roland Corporation in the United States and/or other countries.
Owners Manual
© 2018 Roland Corporation
NOTE
When setting-up or adjusting the stand, take care not to pinch your ngers between movable parts and the main unit. If using this in a location where children are present, be sure to provide adult supervision or guidance.
Prepare an area in which you can perform the assembly safely.
Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.
* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland to prevent the rubber feet from soiling the surface on which they are placed.
1.
Check the parts
1
2
3
4 5 6 11
12
7
8
13
14
9
10
No. Name Quantity
1 Stand 1
2 Curved pipe L 1
3 Curved pipe R 1
4 Straight pipe L (Long) 1
5 Straight pipe R (Short) 1
6 Snare pipe 1
7 Mount holder 3
8 Pad mount 3
9 Pad mount (ball type) 1
10 Cymbal mount (Short) 1
11 Cymbal mount (Long) 2
12 Drum key 1
13 Cable clip 4
14 Cable tie 2
2.
Assembling the Left and Right Arm Sections
Lay the left and right arm sections on the oor while
assembling them.
2–1. Using a drum key, loosen the bolt on the holder of
straight pipe “L, then insert curved pipe “L.
Curved pipe L
2
Straight pipe L
4
Holder
Bolt
2–2. Attach mount holder to straight pipe “L. Then, after
pulling down straight pipe “L until it can move no
further, tighten the bolt.
Curved pipe L
2
Straight pipe L
4
Mount
holder
7
Holder
Bolt
2–3. Using a drum key, loosen the bolt on the holder of
straight pipe “R, then insert curved pipe “R.
Curved pipe R
3
Straight pipe R
5
7 cm
Holder
Bolt
2–4. Position straight pipe “R” so that its tip protrudes by
about 7 cm, and then tighten the holder.
3.
Attach the Left and Right Arm Sections to
the Main Unit
3–1. Use a drum key to loosen bolt of the holder A
(attached to the left-side pipe (with two holders) of
the stand), and insert curved pipe “L (of the assembly
you created in step 2-1–2-2) into holder A of the
stand.
Holder A
Bolt
Curved pipe L
2
Stand
1
As a general rule, insert curved pipe “L until the
guide hole on the pipe can be seen through the
gap in the holder.
After rmly inserting it all the way, use the drum
key to rmly tighten bolt.
Drum key
Bolt
Guide hole
3–2. Lower holder “B” (attached to the right-side pipe
of the stand) to the same position as holder “C”
(attached to the left-side pipe of the stand).
Holder B
Holder C
7 cm
3–3. Use the drum key to loosen bolt of the holder “B, and
insert curved pipe “R” (of the assembly you created in
step 2-3–2-4) into holder “B” of the stand.
Holder B
Bolt
Curved pipe R
3
As a general rule, insert curved pipe “R” until the
guide hole on the pipe can be seen through the
gap in the holder.
After rmly inserting it all the way, use the drum
key to rmly tighten bolt.
Guide hole
Drum key
Bolt
4.
Attaching the snare pipe
4–1. Use the drum key to loosen bolt of the holder C, and
insert the snare pipe into holder “C” of the stand. After
rmly inserting it all the way, use the drum key to
rmly tighten bolt.
Insert the end of the snare pipe that doesn’t have
a cap on it into holder C.
Holder C
Snare pipe
6
Cap
Bolt
Drum key
WARNING: Caution during setup
When setting-up, you must observe the following cautions.
If you fail to observe these cautions, the stand might overturn or fall, causing injury.
Check for stability when setting-up the stand, and take appropriate care.
Do not spread the stand wider
than 1.2 meters (48 inches).
1.2 m
Adjust the rod height so that
no part of any cymbal is higher
than 1.2 meters (48 inches)
above the oor.
1.2 m
Attach the cymbals in such
a way that the center of the
cymbal does not extend beyond
the rear pipes of the stand.
Center of cymbal must not
extend beyond rear of stand
OK
5–5. Attach pad mount (ball type) to the snare pipe, and
tighten the hand knob.
Pad mount (ball
type)
9
Hand knob
6.
Attaching the cymbal mounts
As appropriate for the drum kit that you’re using, attach
the cymbal mounts (short) to the locations for hi-hat
and ride cymbal.
6–1. Insert the two cymbal mounts and the hi-hat mount
into the holders of the curved pipes, and adjust all the
holders as shown in the illustration to complete setup.
A type (for hi-hat)
11
10
8
Pad mounts
9
Pad mount (ball type)
Cymbal mounts (Long)
Cymbal mounts (Short)
“B” type (for ride cymbal)
10
11
8
Pad mounts
9
Pad mount (ball type)
Cymbal mounts (Long)
Cymbal mounts (Short)
Notes
• When setting up or storing the stand, be careful
not to pinch the ngers you use to handle the
stand.
• Regarding the way of mounting a sound module,
pads, or cymbals, please refer to the owner’s
manual supplied with them.
  • Page 1 1

Roland MDS-Compact Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI