PROAIM P-22 User manual

Type
User manual
1
Whats In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is
listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Kite-22 Camera 24.5ft Jib Crane (P-22)
A s s e mb l y Ma n u a l
Packaging Material of Box 1 & 2: 7x Jib Sections
2
Packaging Material of Box 3: Accessories of Jib Crane
Hub Mounting
Section
Head Plaorm with Bolt, Sha
Collars, Washers and Nut
6 x Shanks for Joining Arms
Turn buckle
Joysck Controller Bracket
Levelling Cable
6 x Pins for Joining jibs
7 x Black Velcro
Nut Bolts
2 x Locking Pins
Hub Mounng
knob
Washers
Rear Frame
Mounng Rod
Complimentary
Tools Pouch
Bag Packing
3
Safety Hints
ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT DAMAGE TO EQUIPMENT
& OPERATOR!
The crane may not be assembled or operated under inuence of alcohol, drugs or any other intoxicang
substances. Lack of aenon while connecng the components together can cause substanal damage
to equipment / operator.
The crane may only be operated on levelled horizontal posion. Make sure that the surface is stable.
To prevent any harm or injury, properly join all secons of the crane. It is suggested to use the support
stand while telescoping the complete length.
Always connect the steel cables properly to provide stability to the system. They should not negavely
impact the movements of crane in any way.
Aer setup of the crane, the pan-lt head / gimbal head shall be posioned under the central pivot
secon. In assembled state, when the pan-lt head / gimbal head is higher than central pivot secon,
there should be someone to look aer the crane system.
The complete panning & liing range around it must be kept free. Avoid anybody standing under the
crane. No loose objects may be stored or placed on it. Be very careful while using indoors.
Never operate the crane in the immediate vicinity of high-voltage power cables. It holds danger to life.
Parcular care is required when operang the crane in unfavourable weather condions. The crane
must be shut down in sucient me. When it is used in a rainy day, the pan-lt head / gimbal head and
controlling bar shall be protected against rain.
When you want to transport the crane, lock the Pan & Tilt Axis for safety. Make sure that the
components do not rub together and cause any material wear.
Before the counterweights are removed, ensure the remote head is resng on the support stand. Then
gradually remove the counterweights before remote head, camera or other parts.
In the interest of safe crane operaon, avoid abruptly swivelling or stopping the crane, otherwise it may
cause serious damage to equipment.
FOLLOWING THESE GUIDELINES WILL PROVIDE BETTER SHOTS AND TROUBLE FREE OPERATION.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS AVAILABLE ONLINE BY
CONTACTING THE SALES REPRESENTATIVE.
4
Jib Secons Setup
Insert the rear tube secon (secon 1) into
the hub assembly, slide secon 2 into
secon 1 and align holes of Secon 1 and
secon 2 with the central hole of the hub
assembly and insert shanks in it.
Aer inserng the shanks, properly secure
the jibs together by inserng the jib pin into
the top mounng of the jib.
NOTE: We have provided double locking pre-
cauons on Jib, Knob is rst and primary, pin is
secondary locking, so rst lock the knob to
avoid slipping of secons.
Insert the sha collar into the jib secon and
secure with the wrench.
Then insert the long bolt and nut, washer to
secure the secons properly.
Already aached 1st and 2nd jib secons,
insert it into the hub secon. then insert the
long bolt and nut to secure the secons
properly.
Repeat this process for rest of the secons.
Aach them towards the other Secon 7
with 6, 6 with 5 , 5 with 4, 4 with 3 & 3 with
2.
3 2
5
Repeat this process for rest of the secons.
insert the long bolt and pin, to secure the
secons properly.
Jib secons properly aached to each other
as shown in the picture.
Install Head Plaorm assembly (leveling arm
up) to the end of the secon 7th with the
provided bolt, sha collars, washers and nut.
Head Secon Setup
Insert the bolt back into it, matching the head
secon and secon 7 holes then aach the
provided washers and nut.
Tighten the head secon properly with the
help of Allen key and wrench.
Head secon properly aached with end
secon ghten the top bolt properly to keep
the head secon in line with the jib.
6
Connect one end of the leveling cable to the
head plaorm and insert the other end into
the turnbuckle.
Aach other end with the hub assembly.
Rear Frame Setup
To mount Rear secon of jib, insert the
bolt with washers through one end of the
secon to other. Slide the bolt through and
secure by ghtening with hand.
Put the washer into the bolt and then insert
the nut.
Aer inserng the nut, secure it properly with
the help of the wrench and then loosen the
weight closer to the rear frame and remove
it.
Now add on the weights to the rear frame
and secure the weight closer properly.
7
Match the Rear frame mounng rod with the
top thread of the rear frame; now insert the
rear frame mounng rod into the top thread
of the rear frame and secure it properly.
NOTE: We only use the mounng rod of the
rear frame when we want to mount joysck
digital control on the rear frame, as it is
compable with this mounng rod.
Joysck digital
control
5. 12.8 ’ Jib
Weights required for balancing only Jib (without camera & Pan Tilt) is: 51 Kg (112 lbs)
If the camera weight is 1kg, the jib is balanced with 51+1kg=52kg
If the camera weight is 2kg the jib is balanced with 51+2kg=53kg
4. 15.10’ Jib
Weights required for balancing only Jib (without camera & Pan Tilt) is: 52 Kg (114 lbs)
If the camera weight is 1kg, the jib is balanced with 52+2kg=54kg
If the camera weight is 2kg the jib is balanced with 52+4kg=58kg
2. 22.3’ Jib
Weights required for balancing only Jib (without camera & Pan Tilt) is: 54Kg (119lbs)
If the camera weight is 1kg, the jib is balanced with 54+4kg=58kg
If the camera weight is 2kg the jib is balanced with 54+8kg=62kg
1. 24.5’ Jib
Weights required for balancing only Jib (without camera & Pan Tilt) is: 55Kg (121.5 lbs)
If the camera weight is 1kg, the jib is balanced with 55+5kg=60kg
If the camera weight is 2kg the jib is balanced with 55+10kg=65kg
Balancing Tips
Its secons collapse into each other
3. 19’ Jib
Weights required for balancing only Jib (without camera & Pan Tilt) is: 53Kg (116 lbs)
If the camera weight is 1kg, the jib is balanced with 53+3kg=56kg
If the camera weight is 2kg the jib is balanced with 53+6kg=59kg
8
For Dierent Producon Needs
Converble Shoong Lengths
9
YOUR PROAIM KITE-22 CAMERA 24.5ft JIB CRANE
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesnt cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

PROAIM P-22 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI