CPPDRLK-SP

Scosche CPPDRLK-SP User guide

Hello, I have reviewed the instruction manual for the SCOSCHE USB Relocator CPPDRLK-SP and I am ready to respond to your questions regarding installation, connection and use. This device is intended for USB relocation for Apple CarPlay and Android Auto applications with Power Delivery, with particular attention to proper installation and use of a protective cover in marine environments.
What is the purpose of the protective cover?

What should I do if I have trouble removing the 12V socket?

How do I connect the device power?

Aegleter your product onllne

at

www.scosche.com/register

CPPDRLK-SP

USB Relocator

for

Apple

4D

CarPlayfJ & Android Auto

""

with

Power

Delivery

"

IMPORTANT!

IJ " , uu

•i;

1 r

~~'~,?.:uR,:;~~

-

~.

;.~1~?,~~1~

;~1

:~~u~~Jt"

l

~E'~

'

,.,

, ,.

:,

1

,,,

~

HOURS

MON-FRI

8AM-5

30PM

(PST)

SATURDAY

8AM-2PM

(PST)

/

LIABILITY

DISCLAIMER

This Instruction manual

Is

based

on

carefully documented

data

and research. Scosche Industries

Inc

. cannot

be

held responsible for discrepancies/inconsistencies that

may

occur

due

to

the

vehicle

manufacturing changes

or

options,

or

damages that

may

occur

In the vehicle during the Installation

of

components while using this manual.

1r

you

have

any

further

questions

,

call

our

toll

free

techn

i

cal

help

llne

:

1-l!00-363-4490

x1

or

vis

it

us

ooline

at

www.scosche.com/contact

© 2021

SCOSCHE

INDUSTRIES, INC CPPDRLK-SP 06/21

INSTALLATION

12V

SOCKET REMOVAL

INSTALLATION

NOTE:

These instructions are

provided

as

a

general

guide

and

may

differ

from

your

particular vehicle.

If

you

have

difficulty

removing

the

12V

lighter/

power

socket

in

your

vehicle,

contact

our

tech

support

at

(800)

363-4490

ext

. 1.

Snap-in Type:

1. Use a panel removal

tool

(PRn

to

unsnap

socket

assembly (Figure 1 ).

2. Carefully slide

out,

unplug

power

connector

and

remove (Figure 2).

Thread-in Type:

1. Gain access

the

rear

of

the

12V

socket

assembly

in

the

vehicle

(not

shown).

2.

Unplug

electrical connections

(not

shown).

3. Un-screw

the

locking collar

(counter

clockwise),

carefully slide

socket

out,

and

remove (Figure 3).

I FIGURE 3

CUSTOM INSTALL

1. Choose an area

of

the

dash

that

is free

of

obstructions

behind

the

panel

and

allows

the

cables

to

reach

the

rear

inputs

of

the

stereo.

2. Use a

hole

saw

or

step

drill

bit

to

drill

a

1"

(26mm)

hole

for

the

12V

POWER

plug

(Figure 4).

C

2021

SCOSCHE

INDUSTRIES,

INC 2

--------

~

!FIGURE4f

CPPDRLK-SP

06/21

Opened

Protective

Cover

INSTALLATION

I

FIGURES

I

Closed

Protective

Cover

NOTE

:

Use

of

the

protective (FIGURE

6)

cover is recommended, particularly

for

marine

applications. Install

the

cover

prior

to

installing

the

CPPDRLK-

SP

plug

into

location.

LOCKNUTS

""

FIGURE 7 I

FIGURE I

LOCKNUTS

INSTALLING

THE

CPPDRLK-SP

1. Remove

the

locknut

from

the

CPPDRLK-SP housing (FIGURE 6).

2. Feed

the

connecting cable along

the

body

of

the

unit

through

the

1 "(26mm)

diameter hole (FIGURE

7).

3. Thread

the

backing/lock

nut

onto

the

CPPORLK-SP housing

from

the

rear and

carefully

tighten

in a clockwise direction,

do

NOT

over

tighten

(FIGURE

8).

C

2021

SCOSCHE

INDUSTRIES

, INC 3

CPPDRU<

-

SP

06/

21

INSTALLATION

i

CONNECTING

THE

CPPDRLK-

SP

1. Connect

the

USB

Cable

from

the

CPPDRLK-SP

to

the corresponding

USB

Input

or

dongle

from

the back

of

the

stereo.

2. Connect

the"+"

Positive Male terminal from the back

of

the

CPPDRLK-SP

to

a +12V Accessory

Switched

power

source.

(Socket replacement

):

Use the existing power lead

from

the previous power socket.

(New

Installation

):

Route a new

power

wire (not included)

to

a switched

power

source such

as

the vehicle's fuse bloclc.

3.

Connect

the

..

_. Negative Male terminal from the back

of

the

CPPDRLK-SP

to

Chassis

Ground. (Socket replacement):

Use

the existing Ground wire

from

the

previous

power

socket.

(New Installation): Route a new wire (not included) directly

to

Chassis Ground.

4. Once the CPPDRLK-SP is securely mounted and connected. Re-assemble and remaining

trim

parts

to

complete

your

installation.

C

2021

SCOSCHE

INDUSTRIES,

INC 4

CPPORLK-SP

06/21

/

Related papers

Other documents