Scosche CPPDRLK-SP User guide

Category
Car kits
Type
User guide

Scosche CPPDRLK-SP is a USB relocator for Apple CarPlay and Android Auto with Power Delivery. It allows you to easily add a USB port to your car's dashboard, providing a convenient way to charge and connect your devices while on the road. The CPPDRLK-SP also features a protective cover to keep the USB port clean and protected when not in use.

Scosche CPPDRLK-SP is a USB relocator for Apple CarPlay and Android Auto with Power Delivery. It allows you to easily add a USB port to your car's dashboard, providing a convenient way to charge and connect your devices while on the road. The CPPDRLK-SP also features a protective cover to keep the USB port clean and protected when not in use.

Aegleter your product onllne
at
www.scosche.com/register
CPPDRLK-SP
USB Relocator
for
Apple
4D
CarPlayfJ & Android Auto
""
with
Power
Delivery
"
IMPORTANT!
IJ " , uu
•i;
1 r
~~'~,?.:uR,:;~~
-
~.
;.~1~?,~~1~
;~1
:~~u~~Jt"
l
~E'~
'
,.,
, ,.
:,
1
,,,
~
HOURS
MON-FRI
8AM-5
30PM
(PST)
SATURDAY
8AM-2PM
(PST)
/
LIABILITY
DISCLAIMER
This Instruction manual
Is
based
on
carefully documented
data
and research. Scosche Industries
Inc
. cannot
be
held responsible for discrepancies/inconsistencies that
may
occur
due
to
the
vehicle
manufacturing changes
or
options,
or
damages that
may
occur
In the vehicle during the Installation
of
components while using this manual.
1r
you
have
any
further
questions
,
call
our
toll
free
techn
i
cal
help
llne
:
1-l!00-363-4490
x1
or
vis
it
us
ooline
at
www.scosche.com/contact
© 2021
SCOSCHE
INDUSTRIES, INC CPPDRLK-SP 06/21
INSTALLATION
12V
SOCKET REMOVAL
INSTALLATION
NOTE:
These instructions are
provided
as
a
general
guide
and
may
differ
from
your
particular vehicle.
If
you
have
difficulty
removing
the
12V
lighter/
power
socket
in
your
vehicle,
contact
our
tech
support
at
(800)
363-4490
ext
. 1.
Snap-in Type:
1. Use a panel removal
tool
(PRn
to
unsnap
socket
assembly (Figure 1 ).
2. Carefully slide
out,
unplug
power
connector
and
remove (Figure 2).
Thread-in Type:
1. Gain access
the
rear
of
the
12V
socket
assembly
in
the
vehicle
(not
shown).
2.
Unplug
electrical connections
(not
shown).
3. Un-screw
the
locking collar
(counter
clockwise),
carefully slide
socket
out,
and
remove (Figure 3).
I FIGURE 3
CUSTOM INSTALL
1. Choose an area
of
the
dash
that
is free
of
obstructions
behind
the
panel
and
allows
the
cables
to
reach
the
rear
inputs
of
the
stereo.
2. Use a
hole
saw
or
step
drill
bit
to
drill
a
1"
(26mm)
hole
for
the
12V
POWER
plug
(Figure 4).
C
2021
SCOSCHE
INDUSTRIES,
INC 2
--------
~
!FIGURE4f
CPPDRLK-SP
06/21
Opened
Protective
Cover
INSTALLATION
I
FIGURES
I
Closed
Protective
Cover
NOTE
:
Use
of
the
protective (FIGURE
6)
cover is recommended, particularly
for
marine
applications. Install
the
cover
prior
to
installing
the
CPPDRLK-
SP
plug
into
location.
LOCKNUTS
""
FIGURE 7 I
FIGURE I
LOCKNUTS
INSTALLING
THE
CPPDRLK-SP
1. Remove
the
locknut
from
the
CPPDRLK-SP housing (FIGURE 6).
2. Feed
the
connecting cable along
the
body
of
the
unit
through
the
1 "(26mm)
diameter hole (FIGURE
7).
3. Thread
the
backing/lock
nut
onto
the
CPPORLK-SP housing
from
the
rear and
carefully
tighten
in a clockwise direction,
do
NOT
over
tighten
(FIGURE
8).
C
2021
SCOSCHE
INDUSTRIES
, INC 3
CPPDRU<
-
SP
06/
21
INSTALLATION
i
CONNECTING
THE
CPPDRLK-
SP
1. Connect
the
USB
Cable
from
the
CPPDRLK-SP
to
the corresponding
USB
Input
or
dongle
from
the back
of
the
stereo.
2. Connect
the"+"
Positive Male terminal from the back
of
the
CPPDRLK-SP
to
a +12V Accessory
Switched
power
source.
(Socket replacement
):
Use the existing power lead
from
the previous power socket.
(New
Installation
):
Route a new
power
wire (not included)
to
a switched
power
source such
as
the vehicle's fuse bloclc.
3.
Connect
the
..
_. Negative Male terminal from the back
of
the
CPPDRLK-SP
to
Chassis
Ground. (Socket replacement):
Use
the existing Ground wire
from
the
previous
power
socket.
(New Installation): Route a new wire (not included) directly
to
Chassis Ground.
4. Once the CPPDRLK-SP is securely mounted and connected. Re-assemble and remaining
trim
parts
to
complete
your
installation.
C
2021
SCOSCHE
INDUSTRIES,
INC 4
CPPORLK-SP
06/21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Scosche CPPDRLK-SP User guide

Category
Car kits
Type
User guide

Scosche CPPDRLK-SP is a USB relocator for Apple CarPlay and Android Auto with Power Delivery. It allows you to easily add a USB port to your car's dashboard, providing a convenient way to charge and connect your devices while on the road. The CPPDRLK-SP also features a protective cover to keep the USB port clean and protected when not in use.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI