2. Kichler Lighting
  3. 10198BK

Kichler Lighting 10198BK User manual

  • Hello! I am an AI chatbot trained to assist you with the Kichler Lighting 10198BK User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION INSTRUCTIONS
10198BK/WH
NOTE: This dimmer cannot be used with 10192BK60 or BK96 power supplies.
NOTE: The load on the dimmer cannot exceed 48W. Exceeding 48W may result in damage to the dimmer and tape system.
WARNING:
 •Thedimmershouldalwaysbeinstalledonthe24V,lowoutputsideofthepowersupply.
 • Donotconnectto120V,ordamagetothedimmerandtapesystemmayoccur.
 • Foruseindrylocationsonly.
CONNECTING:
1) The10198in-linedimmermustbeconnecteddirectlytothe24VoutputDC2.1jackfromthepowersupply.Connectthemale
  DC2.1jackfrompowersupplytothefemaleconnectoronthedimmer.
2) ConnectthemaleDC2.1jackofdimmertothefemaleDC2.1jackonthetapelightpowersupplylead.
OPERATING:
1) Toturnlightson,twistthedialonthedimmerclockwiseuntilthelightreachesthedesiredlightlevel.
2) Toturnlightsoffordimdown,turnthedialonthedimmercounterclockwiseuntilthelightreachesthedesiredlightlevelor 
  youreachthefulloffpositionwhichisindicatedbya“click”.
ON
OFF
POWER
SUPPLY
DC 24V
DateIssued:12/7/12 IS-10198-CB
www.kichler.com
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
INSTRUCTIONS D’INSTALLATION
10198BK/WH
REMARQUE :Cegradateurnepeutpasêtreutiliséavecdesalimentations10192BK60ouBK96.
REMARQUE :Lachargedugradateurnepeutpasdépasserles48W.Toutevaleursupérieureà48Wpeutentraînerdesdom-
mages au système gradateur et guirlande.
AVERTISSEMENT :
• Legradateurdoittoujoursêtreinstallésurlecôtédesortiebasse,24Vdel’alimentation.
• Nepasconnecterà120Vsousrisqued’endommagerlesystèmegradateuretguirlande.
• Àutiliseruniquementdansdesendroitssecs.
CONNEXION :
1) Legradateurenligne10198doitêtreconnectédirectementàlapriseDC2.1desortie24Vdel’alimentation.Connecterla
  cheDC2.1mâledel’alimentationàlaprisefemellesurlegradateur.
2) ConnecterlacheDC2.1mâledugradateuràlapriseDC2.1femellesurleconducteurd’alimentationdelaguirlande.
FONCTIONNEMENT :
1) Pourallumer,tournerlecadransurlegradateurdanslesenshorairejusqu’àcequel’éclairageatteigneleniveaudeluminosité
  souhaité.
2) Pouréteindreouassombrir,tournerlecadrandanslesensanti-horairejusqu’àcequel’éclairageatteignedeniveausouhaité
  ouquel’onentendeun«clique»signalantlapositionmaximum.
ALLUMÉ
ÉTEINT
ALIMENTATION
DC 24V
/