Kichler Lighting 44275PN is a versatile and stylish chandelier-style light fixture designed to enhance the ambiance of any room. With its adjustable mounting height and the ability to accommodate a variety of bulb types, this fixture offers customizable lighting solutions. The provided crystal rods and short and long rods allow for personalized configurations, making it a perfect choice for those seeking a unique and elegant lighting experience.
Kichler Lighting 44275PN is a versatile and stylish chandelier-style light fixture designed to enhance the ambiance of any room. With its adjustable mounting height and the ability to accommodate a variety of bulb types, this fixture offers customizable lighting solutions. The provided crystal rods and short and long rods allow for personalized configurations, making it a perfect choice for those seeking a unique and elegant lighting experience.
IS-44275-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Pass xture wire through large lockwasher[E]. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
5) Pass xture wire through hexnut[F]. Thread hexnut onto
end of threaded pipe.
6) Find the appropriate threaded holes on mounng
strap[G]. Assemble mounng screws[H] into threaded
holes.
7) Aach mounng strap to outlet box[I] using the supplied
strap mounng screws[L]. Mounng strap can be
adjusted to suit posion of xture.
8) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
9) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
10) Push xture to ceiling, carefully passing mounng screws
through holes in canopy. NOTE: Be certain wires do not
get pinched between canopy and ceiling.
11) Use knobs[J] and lockwashers[K] to secure canopy.
Tighten to secure.
12) Put into place the twelve (12) crystal rods[M] and using
the supplied alan wrench[P], secure the crystal rods into
place with the set screws[O]. Do not over ghten.
13) Thread into place the sixteen (16) short rods[R] and the
sixteen (16) long rods[N] into the main body as shown.
Note: Rods can be installed to customer preference.
14) Install the recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
[A] Stems
[B] Short
Threaded
Tubes
[C] Swivel
[D] Canopy
[E] Large
Lockwasher
[F] Hexnut
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Knob
[K] Lockwasher
[L] Strap
Mounting
Screws
[M] Crystal Rods
[N] Long Rods
[O] Set Screws
[P] Alan Wrench
[Q] Fixture Body
[R] Short Rods
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Pass xture wire through desired amount of stems[A]
and screw stems together using supplied short threaded
tubes[B]. Thread the stems into the top of the xure
body[Q].
NOTE: A MINIMUM OF ONE (1) 6" STEM MUST BE USED
FOR MOUNTING.
NOTE: Thread locking compound must be applied to
all stem threads as noted with (4) symbol to prevent
accidental rotaon of xture during cleaning, relamping,
etc.
2) Pass xture wire through end of swivel[C] without
threaded pipe. Thread that end of swivel onto end of last
stem.
NOTE: Direcon of swivel in accordance with ceiling.
3) Pass xture wire through hole in canopy[D]. Pass
threaded pipe on end of swivel up through hole in
canopy.
Installaon Instrucons (connued)
I
G
D
H
K
J
L
►
Q
A
►
B
►►
►►
►►
►
C
F
E
N
M
P
O
R
IS-44275-CB
Nous sommes là pour vous aider 866-558-5706
Heures : du lundi au vendredi, de 9h à 17h (heure de l’Est)
INSTRUCTIONS:
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installaon Au Canada
2) Passer le l de xaon à travers l’extrémité de
pivotement[C] sans tuyau leté. Enlez l’extrémité de
pivotement sur l’extrémité de la dernière ge.
REMARQUE: pivotante en conformité avec le plafond.
3) Faire passer le l de xaon à travers le trou dans la
canopée[D]. Passez tuyau leté sur l’extrémité de pivot
dans le trou de la canopée.
4) Faire passer le l de xaon dans le trou de la rondelle
d’arrêt[E]. Enler la rondelle d’arrêt sur l’extrémité du
tuyau leté faisant saillie à l’intérieur de la canopée.
5) Faire passer le l de xaon dans le trou du hexnut[F].
Enlez hexnut sur l’extrémité du tuyau leté.
6) Trouvez les trous taraudés appropriés sur sangle de
xaon[G]. Monter les vis de montage dans les trous
letés[H].
7) Fixez la courroie de montage à la boîte de sore[I] à
l’aide des vis de xaon de la courroie[L] fournies. La
Sangle de xaon peut être ajustée en foncon de la
posion de montage.
8) Connecter les ls. Se reporter au tableau ci-dessous pour
faire les connexions.
Connecter le l noir ou
rouge de la boite
Connecter le l blanc de
la boîte
A Noir A Blanc
*Au cordon parallèle (rond
et lisse)
*Au cordon parallèle (à
angles droits el strié)
Au transparent, doré,
marron, ou noir sans l
disncf
Au transparent, doré,
marron, ou noir avec un l
disncf
Fil isolé (sauf l vert) avec
conducteur en cuivre
Fil isolé (sauf l vert) avec
conducteur en argent
*Remarque: Avec emploi d’un
l paralléle (SPT 1 et SPT 2). Le
l neutre est á angles droits ou
strié et l’autre l doit étre rond
ou lisse (Voir le schéma).
Fil Neutre
9) Pousser le luminaire contre le plafond, en passant
avec soin les vis de montage à travers les trous dans le
couvercle. REMARQUE : Vous assurer que tous les ls
sont dans le couvercle et ne se retrouvent pas pincés
entre le couvercle et le plafond.
10) Ulisez les boutons de verrouillage[J] et les lave-
glaces[K] pour sécuriser la voilure. Serrez pour sécuriser.
11) Put into place the twelve (12) crystal rods[M] and using
the supplied alan wrench[P], secure the crystal rods into
place with the set screws[O]. Do not over ghten.
12) Thread into place the sixteen (16) short rods[R] and
the sixteen (16) long rods[N] into the main body as
shown. Note that the rods can be installed to customer
preference.
13) Installer la ou les ampoules recommandées (Non
fournies).
Diagramme d’appareils
ATTENTION – RISQUE DE DÉCHARGES ÉLECTRIQUES -
Couper le courant au niveau du panneau du disjoncteur du
circuit principal ou de la boîte à fusibles principale avant de
procéder à l’installaon.
ATTENTION:
Ce luminaire doit être installé conformément aux codes
d’électricité naonaux (NEC) et sasfaire toutes les
spécicaons des codes locaux. Si vous ne connaissez pas
les exigences de ces codes, il est recommandé de coner
l’installaon à un électricien ceré.
Liste des Pièces
Précauons
[A] Tiges
[B] Tubes à
Filetage Court
[C] Pivot
[D] Canopée
[E] Rondelle De
Blocage
[F] Ecrou
Hexagona
[G] Étrier de
Montage
[H] Vis De
Montage
[I] Boîte  Prises
[J] Bouton
[K] Rondelle De
Blocage
[L] Vis de Fixation
de la Courroie
[M] Crystal Rods
[N] Long Rods
[O] Set Screws
[P] Alan Wrench
[Q] Fixture Body
[R] Short Rods
Instrucons d’installaon
I
G
D
H
K
J
L
►
Q
A
►
B
►►
►►
►►
►
C
F
E
N
M
P
O
R
1) Passer le l de xaon à travers la quanté souhaitée de
ges[A] et la visdérive en ulisant des tubes à letage
court[B] fournis. Thread the assembled stems into the
top of the xture body[Q].
NOTE: A MINIMUM OF ONE (1) 6” STEM MUST BE USED
FOR MOUNTING.
REMARQUE: le composé de verrouillage de letage doit
être appliqué à tous les ls de la ge comme indiqué
avec un symbole éché pour empêcher la rotaon
accidentelle du luminaire pendant le neoyage, la
relamping, etc.
Instrucons d’installaon (a connué)
-
1
-
2
Kichler Lighting 44275PN is a versatile and stylish chandelier-style light fixture designed to enhance the ambiance of any room. With its adjustable mounting height and the ability to accommodate a variety of bulb types, this fixture offers customizable lighting solutions. The provided crystal rods and short and long rods allow for personalized configurations, making it a perfect choice for those seeking a unique and elegant lighting experience.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 43964PN User manual
-
Kichler Lighting 43964PN User manual
-
Kichler Lighting 44202PN User manual
-
Kichler Lighting 43966PN User manual
-
-
Kichler Lighting 44276PN User manual
-
Kichler Lighting 44065NI User manual
-
Kichler Lighting 43722PN User manual
-
Kichler Lighting 44270PN User manual
-
Kichler Lighting 44053NI User manual
