Vollrath Cup Dispenser, Spring-Loaded, In-counter Installation guide

Brand: Vollrath

Model: Cup Dispenser, Spring-Loaded, In-counter

Type: Installation guide

Installation Instructions

2017 The Vollrath Company L.L.C. Part No. 350719-1 ml 3/30/17

Spring Loaded In-Counter Cup Dispenser

Thank you for purchasing this Vollrath equipment. Before operating the

equipment, read and familiarize yourself with the following operating

and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. Save the original box and packaging. Use this packaging

to ship the equipment if repairs are needed.

SAFETY PRECAUTIONS

To ensure safe operation, read the following statements and understand

their meaning. This manual contains safety precautions which are

explained below. Please read carefully.

Warning is used to indicate the presence of a hazard that will or can

cause severe personal injury or death.

Caution is used to indicate the presence of a hazard that will or can

cause minor or major personal injury if the caution is ignored.

NOTICE: Notice is used to note information that is important but not

hazard-related.

TOOLS YOU WILL NEED

• #2 Phillips Screwdriver

• Drill

• ¹⁄₈" Drill Bit (For #29 Pilot Hole)

• Sabre Saw or Hand Router

• 3 #8 x 1.00" Pan Head Phillips Screws (included)

CHOOSE THE CORRECT SPRING

The dispenser includes two springs for different applications. See the

chart below. The lighter weight dispenser is factory installed. See

“Change Default Spring (Optional)” on page 3.

INSTALLATION

Mount the Dispenser

1. Cut the appropriate diameter opening in the mounting surface.

2. Lift the bezel to remove it from the tube to revel the mounting holes

and the components that can be adjusted to accommodate different

cup diameters.

WARNING

CAUTION

Mounting Dispensing Use This Spring

Vertical

Paper or Plastic Heavier Weight

Foam Lighter Weight

Horizontal Paper, Plastic or Foam Lighter Weight

Angled

Paper or Plastic Heavier Weight

Foam Lighter Weight

Item No. For Cup Rim Diameter Cutout Diameter

CADJ-1 2¹⁄₂ –3¹⁄₂" (6.4 – 8.9 cm) 4 (10.2)

CADJ-2 3 – 3⁷⁄₈"(7.6 – 9.8 cm) 4¹⁄₂ (11.4)

CADJ-3 3 – 4⁵⁄₈" (7.6 – 11.7 cm) 5¹⁄₄ (13.3)

CADJ-4 4¹⁄₂ –5¹⁄₄" (11.4 – 13.3 cm) 5³⁄₄ (14.6)

2 Spring Loaded In-Counter Cup Dispenser Operator’s Manual

3. Rotate the adjustment ring to reveal the mounting holes.

4. Place the tube into the cut mounting hole. Mark the mounting hole

locations.

5. Remove the dispenser from the mounting hole.

6. Pre-drill pilot the pilot holes. Vollrath suggests a ¹⁄₈" (0.125)

diameter pilot hole diameter of ¹⁄₈" (0.125).

7. Insert the dispenser into the cutout hole and align the mounting

holes to the pre-drilled holes.

8. Insert the included screws into the mounting holes. Tighten snuggly.

ADJUST DIAMETER TO FIT CUPS

1. Loosen, but do not remove adjusting ring screws.

2. Rotate the adjusting ring to widen the opening.

3. Insert a short stack of cups into the dispenser.

4. Rotate the adjusting ring until the cups are held in place.

Mounting

hole

Mounting

hole

Mounting hole

Adjusting

Ring Screw

Adjusting

Ring Screw

Adjusting Ring Screw

Spring Loaded In-Counter Cup Dispenser Operator’s Manual 3

5. Lightly tighten one of the adjusting ring screws to hold the ring in

place.

TEST THE DISPENSER

1. Test the dispenser by pulling a cup from the tube.

2. Rotate the adjustment ring as necessary to achieve one-at-time cup

dispensing with minimum drag.

3. Fill the dispenser with a full stack of cups and retest the

performance. Adjust the ring as necessary.

4. Tighten the three adjusting ring screws. Do not over-tighten.

5. Re-attach the bezel to the dispenser. Note the bezel does not need to

be removed to refill cups.

CLEANING

NOTICE: Do not use abrasive materials, scratching cleansers or

scouring pad to clean the unit. These can damage the

finish.

Clean the dispenser on a regular basis.

1. Remove the bezel.

2. Remove all of the cups.

3. Push plate and spring down.

4. While holding down the plate, wipe the interior with a soft cloth

damp cloth.

5. Dry the interior with a soft cloth.

6. Reinstall the bezel.

CHANGE DEFAULT SPRING (OPTIONAL)

1. Pull off the retaining ring from the bottom the dispenser. Remove

the end cap.

NOTICE: Notice the cap is under pressure from the spring.

2. Remove the spring and insert the heavier weight spring.

3. Align the holes in the tube to those in the end cap. Reinstall the end

cap and retaining ring.

Adjusting

ring screw

Adjusting

ring screw

Adjusting ring screw

2017 The Vollrath Company L.L.C. Part No. 350719-1 ml 3/30/17

www.vollrath.com

The Vollrath Company, L.L.C.

1236 North 18th Street

Sheboygan, WI 53081-3201 U.S.A.

Main Tel: 800.624.2051 or 920.457.4851

Main Fax: 800.752.5620 or 920.459.6573

Customer Service: 800.628.0830

Canada Customer Service: 800.695.8560

Technical Services

[email protected]

Induction Products: 800.825.6036

Countertop Warming Products: 800.354.1970

All Other Products: 800.628.0832

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.

To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to

The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions.

When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of

purchase showing the date the unit was purchased.

WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.

This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written

warranty to purchasers for such uses.

The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically

described in our full warranty statement. In all cases, the warranty runs from the date of the end user’s original purchase date found on the receipt.

Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will

not be covered under warranty.

For complete warranty information, product registration and new product announcement, visit www.vollrath.com.

Page is loading ...

Vollrath Cup Dispenser, Spring-Loaded, In-counter Installation guide

Brand: Vollrath

Model: Cup Dispenser, Spring-Loaded, In-counter

Type: Installation guide

Download PDF

report

Vollrath Cup Dispenser, Spring-Loaded, In-counter Installation guide

Vollrath Cup Dispenser, Spring-Loaded, In-counter Installation guide

in other languages

Related papers