Page is loading ...
Installation Instructions
©
2017 The Vollrath Company L.L.C. Part No. 350719-1 ml 3/30/17
Spring Loaded In-Counter Cup Dispenser
Thank you for purchasing this Vollrath equipment. Before operating the
equipment, read and familiarize yourself with the following operating
and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. Save the original box and packaging. Use this packaging
to ship the equipment if repairs are needed.
SAFETY PRECAUTIONS
To ensure safe operation, read the following statements and understand
their meaning. This manual contains safety precautions which are
explained below. Please read carefully.
Warning is used to indicate the presence of a hazard that will or can
cause severe personal injury or death.
Caution is used to indicate the presence of a hazard that will or can
cause minor or major personal injury if the caution is ignored.
NOTICE: Notice is used to note information that is important but not
hazard-related.
TOOLS YOU WILL NEED
• #2 Phillips Screwdriver
• Drill
• ¹⁄₈" Drill Bit (For #29 Pilot Hole)
• Sabre Saw or Hand Router
• 3 #8 x 1.00" Pan Head Phillips Screws (included)
CHOOSE THE CORRECT SPRING
The dispenser includes two springs for different applications. See the
chart below. The lighter weight dispenser is factory installed. See
“Change Default Spring (Optional)” on page 3.
INSTALLATION
Mount the Dispenser
1. Cut the appropriate diameter opening in the mounting surface.
2. Lift the bezel to remove it from the tube to revel the mounting holes
and the components that can be adjusted to accommodate different
cup diameters.
WARNING
CAUTION
Mounting Dispensing Use This Spring
Vertical
Paper or Plastic Heavier Weight
Foam Lighter Weight
Horizontal Paper, Plastic or Foam Lighter Weight
Angled
Paper or Plastic Heavier Weight
Foam Lighter Weight
Item No. For Cup Rim Diameter Cutout Diameter
CADJ-1 2¹⁄₂ –3¹⁄₂" (6.4 – 8.9 cm) 4 (10.2)
CADJ-2 3 – 3⁷⁄₈"(7.6 – 9.8 cm) 4¹⁄₂ (11.4)
CADJ-3 3 – 4⁵⁄₈" (7.6 – 11.7 cm) 5¹⁄₄ (13.3)
CADJ-4 4¹⁄₂ –5¹⁄₄" (11.4 – 13.3 cm) 5³⁄₄ (14.6)
2 Spring Loaded In-Counter Cup Dispenser Operator’s Manual
3. Rotate the adjustment ring to reveal the mounting holes.
4. Place the tube into the cut mounting hole. Mark the mounting hole
locations.
5. Remove the dispenser from the mounting hole.
6. Pre-drill pilot the pilot holes. Vollrath suggests a ¹⁄₈" (0.125)
diameter pilot hole diameter of ¹⁄₈" (0.125).
7. Insert the dispenser into the cutout hole and align the mounting
holes to the pre-drilled holes.
8. Insert the included screws into the mounting holes. Tighten snuggly.
ADJUST DIAMETER TO FIT CUPS
1. Loosen, but do not remove adjusting ring screws.
2. Rotate the adjusting ring to widen the opening.
3. Insert a short stack of cups into the dispenser.
4. Rotate the adjusting ring until the cups are held in place.
Mounting
hole
Mounting
hole
Mounting hole
Adjusting
Ring Screw
Adjusting
Ring Screw
Adjusting Ring Screw
Spring Loaded In-Counter Cup Dispenser Operator’s Manual 3
5. Lightly tighten one of the adjusting ring screws to hold the ring in
place.
TEST THE DISPENSER
1. Test the dispenser by pulling a cup from the tube.
2. Rotate the adjustment ring as necessary to achieve one-at-time cup
dispensing with minimum drag.
3. Fill the dispenser with a full stack of cups and retest the
performance. Adjust the ring as necessary.
4. Tighten the three adjusting ring screws. Do not over-tighten.
5. Re-attach the bezel to the dispenser. Note the bezel does not need to
be removed to refill cups.
CLEANING
NOTICE: Do not use abrasive materials, scratching cleansers or
scouring pad to clean the unit. These can damage the
finish.
Clean the dispenser on a regular basis.
1. Remove the bezel.
2. Remove all of the cups.
3. Push plate and spring down.
4. While holding down the plate, wipe the interior with a soft cloth
damp cloth.
5. Dry the interior with a soft cloth.
6. Reinstall the bezel.
CHANGE DEFAULT SPRING (OPTIONAL)
1. Pull off the retaining ring from the bottom the dispenser. Remove
the end cap.
NOTICE: Notice the cap is under pressure from the spring.
2. Remove the spring and insert the heavier weight spring.
3. Align the holes in the tube to those in the end cap. Reinstall the end
cap and retaining ring.
Adjusting
ring screw
Adjusting
ring screw
Adjusting ring screw
©
2017 The Vollrath Company L.L.C. Part No. 350719-1 ml 3/30/17
www.vollrath.com
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560
Technical Services
Induction Products: 800.825.6036
Countertop Warming Products: 800.354.1970
All Other Products: 800.628.0832
SERVICE AND REPAIR
Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions.
When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written
warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs from the date of the end user’s original purchase date found on the receipt.
Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will
not be covered under warranty.
For complete warranty information, product registration and new product announcement, visit www.vollrath.com.
/