Acrosser Technology ACE-MINI Owner's manual

Revision: 1.0

1

Revision Description Date

1.0 Release 2009/12/29

ACE-Mini

System Guide

Revision: 1.0

2

Contents

1 Introduction to ACE-MINI .........................................................4

1.1 Specifications.................................................................................... 8

1.2 Packing List....................................................................................... 8

1.3 System Dissection............................................................................ 9

2 Procedures of Assembly/Disassembly ...................................12

2.1 Installing the power cable hook .................................................... 12

2.2 Installing the 2.5” Hard Disk Driver (HDD).................................... 15

2.3 Installing the mainboard procedures............................................ 22

2.4 Installing the ACE-B2019/A Batteries............................................ 24

3 ACE-B2019/A Series Guide (ACE-B2019, ACE-B2019A)........27

3.1 Block Diagram................................................................................. 27

3.2 ACE-B2019/A H/W Information ...................................................... 28

3.2.1 ACE-B2019/A LAYOUT (Top side)...........................................................28

3.2.2 ACE-B2019/A LAYOUT (Bottom side).....................................................29

3.3 Connectors and Jumpers Setting ................................................. 30

3.3.1 Locations...................................................................................................30

3.3.2 Components and Jumps Setting List......................................................31

3.4 AGC Register Description.............................................................. 36

3.4.1 PCI Configuration Register......................................................................36

3.4.2 SRAM Memory Address Map...................................................................42

3.4.3 I/O-Interface Address Map .......................................................................43

3.6 OXUPCI954 Drive Installation Guide............................................. 79

3.7 Electrical Characteristics............................................................... 88

3.7.1 Basic Electrical Characteristics ..............................................................88

3.7.2 72-PIN Golden Finger...............................................................................89

3.7.3 Spare GPIO connector (For ACE-B2019A Only).....................................91

3.7.4 AGC Port Assignment..............................................................................93

3.7.5 NOTES (72-PIN Gold Finger I/O)..............................................................97

Revision: 1.0

3

4 Acrosser Intelligent Reel Controller (AR-B2009)....................99

4.1 Structure of Acrosser Intelligent Reel Controller ...................... 100

4.2 AR-B2009 LAYOUT........................................................................ 101

4.3 CONNECTOR S SETTING............................................................. 102

4.4 REEL Control Step........................................................................ 107

Revision: 1.0

4

1 Introduction to ACE-MINI

ACE-MINI series is a solution for gaming machine system integrators who want to use

low cost and flexible MINI-ITX motherboard as the computing platform. ACE-MINI contains a

PCI bus gaming I/O control card (ACE-B2019/A), an AC input power supply and a chassis.

Any MINI-ITX motherboard with a PCI slot can fit in the ACE-MINI. There are five

configurations in ACE-MINI series.

Table 1 ACE-MINI SKU table

Configuration Chassis Gaming I/O

card

Mother

board

Reel mechanism

controller

(AR-B2009)

PSU

ACE-MINI Yes ACE-B2019 No No 180W

ACE-MINI-A Yes ACE-B2019A No No 180W

ACE-MINI5495 Yes ACE-B2019 AR-B5495 No 100W

ACE-MINI5495A Yes ACE-B2019A AR-B5495 No 100W

ACE-MINI5495R Yes ACE-B2019A AR-B5495 Yes 100W

Note: There will be more standard MINI-ITX mother board from Acrosser. Please contact

with Acrosser’s sales representative for further information.

Table 2 Comparison of ACE-B2019 and ACE-B2019A

Features AR-B2019 AR-B2019A

Serial Ports No 1. COM1: TTL/RS232.

2. COM2:

RS232-COM2/ccTlak1

3. COM3:

RS232-COM3/ccTlak2

Intrusion logger No Yes

SRAM 256KB 512KB x 2

Secured real time clock No Yes

iButton retainer, ProtectU No Yes

GPIO No 28 bits

Battery low detection No Yes

Revision: 1.0

5

 ACE-B2019A Component-side:

 ACE-B2019A Bottom-side:

Revision: 1.0

6

 ACE-B2019 Component -side:

 ACE-B2019 Bottom-side:

Revision: 1.0

7

Features:

 Mini-ITX chassis with PCI Gaming I/O card.

 Is suitable for any Mini-ITX motherboard with PCI slot.

 Standard 8-liner 72-pin plus 10-pin interface.

 30 Digital Inputs, 27 digital outputs, 512KB NVRAM , 4 x 16-bittimers.

 Chassis intrusion switch.

 3 x Serial ports, Intrusion logger, Real Time Clock, Software protection (AR-B2019A).

Description Mini ITX Chassis with Gaming Control Card

Dimension Depth: 266.2 * 245.5 * 134.5mm.

System Thermal One system fan.

CPU Board Standard Mini-ITX motherboard with PCI slot.

Storage One 2.5” HDD bay.

Chassis Intrusion

Switch

One chassis intrusion switch.

Front Panel 1. Standard Mini-ITX bracket opening.

2. 1 x PCI card bracket.

3. D-sub 9 connector opening.

4. Power LED.

5. ATX power switch.

Gaming I/O 1. 8-liner interface.

2. 30 x 5KV optical isolated digital inputs.

3. 24 x 500mA MOSFET outputs.

4. 2 x 1000mA output for tower lamps.

5. One 180 degrees 8-bit readable DIP switch.

6. Four 16-bit timers with timeout interrupt.

7. 256KB or dual 512KB SRAM with battery backup.

8. Optional advanced version (AR-B2019A).

a. 3 serial ports (RS-232C, TTL, ccTalk). SAS bit-9 protocol support.

b. Intrusion logger.

c. Secured real time clock.

d. Software security: ProtectU(programmable ID) & Dallas iButton

socket.

e. Reel mechanism controller, support up to 6 reels

(ACE-MINI5495R).

Software

development kit

1. Supports Windows XP, XP embedded and Linux.

2. Device drivers.

3. Application Program Interface (API).

Power Supply 180 or 100 Watts ATX power supply.

Revision: 1.0

8

1.1 Specifications

Item Description

System ACE-MINI Series

CPU Board AR-B5495(ACE-MINI5495(A)(R) model)

System Dimensions 265*254.5*134.5(mm)

1.2 Packing List

Description Quantity Remark

ACE-MINI series 1

AR-B5495 accessory pack 1

ACE-MINI5495(A)(R)

model：

1. COM cable * 2

2. SATA power cable * 1

3. SATA cable * 2

4. IDE cable * 1

5. CD ROM

Mounting bracket

2

AC Power cord

1

CD ROM

1

SATA power cable

1 ACE-MINI(-A) model

SATA cable

1

Revision: 1.0

9

1.3 System Dissection

(1) Dimensions

(2) Front Panel (ACE-MINI5495R model type)

Key board & mouse LPT1

VGA

POWER SWITCH & LED

COM LAN USB 1~4

CC TALK

POWER JACK

Reel A~F COM 1~3

LINE IN/OUT

Revision: 1.0

10

(3)System Configuration

1

3

2

4

12

13

14

15

16

17

11

5

7

6

8

9

10

Revision: 1.0

11

Item Description Quantity

1 TOP COVER 1

2 AR-B2009(ACE-MINI5495R TYPE) 1

3 FAN 1

4 BOTTOM BASE 1

5 HDD BRACKET 1

6 AR-B5495(ACE-MINI5495(A)(R) TYPE) 1

7 MAIN BOARD IO BRACKET 1

8 COM3 1

9 POWER SUPPLY 1

10 POWER CORD HOOK 1

11 SLOT 3.96mm 20PIN 1

12 SLOT 3.96mm 72PIN

1

13 ACE-B2019(A) 1

14 CHASSIS INTRUSION SWITCH 1

15 POWER LED 1

16 ATX POWER SWITCH 1

17 MOUNTING BRACKET 2

Revision: 1.0

12

2 Procedures of Assembly/Disassembly

2.1 Installing the power cable hook

1. Please take out the hook that attached from packing package, and then install it on

position below.

2. The good way to install the hook, it should be installed the right side first then left side

installing.

Revision: 1.0

13

3. Make sure the hook has been installed firmly.

Revision: 1.0

14

Revision: 1.0

15

2.2 Installing the 2.5” Hard Disk Driver (HDD)

1. Unfasten three screws to take off the top cover.

2. Open the top cover following the direction.

Revision: 1.0

16

3. Before take off the top cover, please notice to keep away from the ACE-B2019 golden

finger.

4. If the system has a reel function (ACE-MINI5495R), please take care of the reel cable

connecting.

Revision: 1.0

17

5. Release the HDD bracket via unscrewing four screws.

6. Find the HDD screws (M3*5L) from packing packet.

Revision: 1.0

18

7. Assemble the HDD in HDD bracket with four screws.(Notice the HDD direction)

8. Connect the SATA cable & power cable to the HDD.

(Notice: For ACE-MINI & ACE-MINI-A series, the power supply has no the SATA power

connector. Please take the SATA power adapter cable from packing packet. And then

connect to power supply first.)

Revision: 1.0

19

9. Fix the HDD module via four screws.

10. Align the position to place the top cover back.

Revision: 1.0

20

11. Push the top cover into the bottom case following the direction below.

12. Close the top cover.

Page is loading ...

Acrosser Technology ACE-MINI Owner's manual

Acrosser Technology ACE-MINI Owner's manual

Related papers

Other documents