2. Conlan
  3. M1000

Conlan M1000 User manual

  • Hello! I am an AI chatbot trained to assist you with the Conlan M1000 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Mifare reader
M1000
Art. No: 480060 (black), 480061 (white)
User manual
M1000_usermanual_ENGfeb19
2
Table of Contents
1. Introduction
2. Installation
3. Programming users
3.1 Mastertransponder
3.2 Programming user tags
3.3 Deleting user tags
4. Conguration
4.1 Programming mode
4.2 Backup/cloning
4.3 Settings
4.3.1 OC Split
4.3.2 OC Inverted
4.3.3 Timeout
4.3.4 Free locker
page 3
page 3
page 4
page 4
page 4
page 4
page 5
page 5
page 5
page 5
page 5
page 5
page 6
page 6
3
1. Introduction
M1000isaexibleMifarereaderformanyapplications.Thereaderhas3LED’s(yel-
low, green and red) for indication of approved/rejected tag and for navigation when
conguratingthereaderssettings.80users(possiblein2blocksforindividualout-
put).
InstandbytheyellowLEDislit(● ○ ○)
ByapprovedtagorcardtheyellowandgreenLEDarelit(● ● ○)
ByrejectedtagorcardtheredLEDislit(○ ○ ●)
2. Installation
Mount the reader on a even surface.
Connectthewirestopowersupply,lockingdevice,assemblyboxetc.
Note:Rightafterthevoltageisappliedlightsall3LED’sandthebuzzersounds.
RightaftertheyellowLEDashesandthebuzzerissilent.
3. Programming user tags
3.1 Master transponder
BeforeyoucanusetheM1000youhavetoprogramaMastertransponder
(indication = * ○ ○).ShowthattagyouwantasMastertransponder,agreenlight
conrmstheprogrammingandtheM1000isnowreadyforprogrammingusertags
andconguratingthesettings.
3.2 Programming new user tags
TheM1000has2outputs(yellowandwhitewire)thatcanactivateeachlockingdevice.
Bydefaultatcivatesalltagsoutput2.Tosplittheoutputssee“OCSplit”.
○ ● ○ * ● ○ → ○ ● ○ * ● ○ → ○ ● ○
Toexittheprogramming,waitfor30secondsordisconnectandreconnectthe
voltage.
3.3 Deleting user tags
Deleting individual users
● ● ○ ● ● * → ● ● ○ ● ● * → ● ● ○
The M1000 can also delete all users at once, delete a lost user and delete the master
transponder.Usetheenclosedcongurationschemeasaguide.
4
Show the Master tag
1 time
Show a Mifare tag
Show a Mifare tag
etc.
Show the Master tag
2 times
Show a Mifare tag
Show a Mifare tag
etc.
4.Conguration
4.1 Programming mode
ToconguretheM1000,thereadermustbedisconnectedandreconnected(forabout
2seconds).NowtheMastertranspondercanconguretheM1000’ssettings.Please
seethecongurationschema// markings.
RemembertoshowtheMasterTransponderwithin10secondstoallowyoutochange
theM1000’scongurations(timeout).
Thefollowingcongurationsonlyworkafterpoweron/oasdescribed.
4.2 Backup/cloning
TheM1000’sinformationcanbestoredandloadedwithaBackupcard
(Art.No.480080).Pleaseseetheenclosedcongurationschemeforfurther
information.
4.3 Settings
These settings can split the outputs, invert the outputs, and set the timeout.
Usetheenclosedcongurationscheme.
4.3.1 OC Split(1ashontheyellowLED)
Fromthefactory,theloadedtagsenablebothoutputs(userspace1to80).Thisset-
tingdividestheuserlocations.User1to40activatesoutput2(yellowwire)anduser
space 41 to 80 activates output 1 (white wire).
Show master transponder for toggle (● = split, ● = combined).
4.3.2 OC1 and OC2 inverted(2or3ashesontheyellowLED)
ThesefunctionsinverttheM1000’soutputs(2ashesforoutput1and3ashesfor
output 2).
(● = inverted, ● = not inverted).
5
6
4.3.3 Timeout (4ashesontheyellowLED)
ThisfunctionsetstheM1000’stimeouttime.Showthemastertranspondertostart,
thebuzzergivesabeepforeverysecond,showthemastertransponderagaintoend
the count.
4.3.4 Free locker (5ashesontheyellowLED)
TheFreelockerfunctioncanbeusedforaccesscontrol,especiallywheretheuser
often switches.
Showthereaderacardortag,andifthecabinetisfree,itwilllockandcanonlybe
unlocked with the same card or tag.
Free locker timeout
Countforhours,soifyouwantittobesetto4hours,waitfor4seconds.
Save0forthereadernottoopenafterxhours,butonlywhenthecard/tagis
showed to the reader again. Default is set to 10 hours.
User position 1 resets free locker.
7
ThankyouforchoosingConlan’sproducts.
For further assistance, please contact
Our support service.
/