Nienkamper Vox Forum L Series Installation guide

Type
Installation guide
T
el 800 668 9318
T
el 416 298 5700
Fa
x 416 298 9535
mail@nienkamper.com
www.nienkamper.com
L - Series
INSTALLATION GUIDE
MODEL FORUM L-SERIES ALL CONFIGURATIONS
It is important to protect furniture worksurface while installing this product!
READY READY
SITE-WIRED
12
3 4
GETTING ACCESS FOR FACEPLATE OPENING FLAP
REMOVING FACEPLATE SCREWS REMOVING FACEPLATE
If faceplate modules have been specified for site wired connections, it
w
ill be necessary to remove faceplate modules.
Start by removing one Allan head machine screw from the bottom
c
orner of either end plate.
Allan key is provided.
Once the two machine screws are removed from the endplates, rotate
t
he aluminum flap at the base of the faceplates to expose Phillips head
f
aceplate screws.
I
mportant!
This electrical device is provided fully wired and should not be
t
ampered with.
Tampering with this device voids warranty and may cause electrical shock.
Please note, for detailed instructions about this Vox Forum - see the last
page after the installation photographs.
For information please call Nienkamper Customer Service at 1-800-668-9318.
For e-mail inquiries:
mail@nienkamper.com
Each faceplate module is fixed with two machine screws.
Remove the screws below the faceplate to be removed.
Once faceplate screws have been removed,
f
aceplate is easily tak
en out of the assembly
.
Complete connections to the f
aceplate module and r
e-install
opposite to removal.
!
56
7 8
INSTALLING INTO TOP FASTENING TO TOP
WIRE MANAGEMENT FINISHED PR
ODUCT
Once all connections have been made and forum is re-assembled, posi-
t
ion into the table top hole.
Align the four thread inserts with their positions in the top.
From the underside of the top, fasten the four 1
1
/4" – 10-24 Phillips pan
head screws provided.
S
tart all fasteners and tighten uniformly.
Adhesive wire management strips are supplied and can be positioned
where needed.
Cables can be inser
ted into 1 of 3 channels
.
INSTALLATION AND OPERATING INSTRUCTIONS
VOX FORUM L-SERIES
Please read instructions carefully
WARNING:
GENERAL USE:
QUESTIONS:
Electrical components are provided fully wired. These components should not be tampered with.
Maximum two power output modules can be installed to one appliance.
This installation should be made by a qualified service person and should conform to all local codes.
More then one power supply, disconnect all power supplies before servicing.
Provides an access point to the top of a table surface to allow plug in convenience for voice/data/power receptacles.
Requires no maintenance but care should be taken to reduce the risk of foreign matter or liquids from falling
onto the assembly.
Flexible power cord assemblies include a reset fuse in case the power circuit is overloaded. To reset the fuse,
simply push the small round black button on the faceplate.
This product is intended for office equipment and laptop computer use only. Heavy equipment or maintenance
equipment should not be plugged into the device.
For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible.
For PERMANENTLY CONNECTED EQUIPMENT, a readily accessible disconnect device shall be incorporated in the building installation wiring.
Site wired power modules are provided with a 3' long shielded metallic cable fully wired to the receptacle.
Simply connect metallic cable end to source.
Please call: Nienkämper Customer Service at 1-800-668-9318.
Email:
mail@nienkamper.com
632030
V.1 02/05
Shielded Metallic Cable
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Nienkamper Vox Forum L Series Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI