GE ZIFS36NMGRH Installation guide

Brand: GE

Model: ZIFS36NMGRH

Type: Installation guide

GE Monogram ®

Installation

Instructions

Stainless Steel

36" Built-In

Refrigerators

and Freezers

Modds

ZIRS36N LH- All Refiqgemtor

ZIRS 36N RH- All Refiqgemtor

ZIFS36N LH- All b)'wezer

ZIFS 36N RH- A ll F_vezer

Before you begin - Readthese instructions completely and carefully.

IMPORTANT- Savethese instructions for local inspector's use.

IMPORTANT- OBSERVEALL GOVERNINGCODESAND ORDINANCES.

Note to Installer- Be sure to leave these instructions with the Consumer.

Note to Consumer- Keep these instructions with your Owner's Manual for future reference.

Inrlv/'.4 Thisappliance must be properlygrounded.See "Grounding the Refrigerator,"page7.

[.pl___i_BIII _]i,_i II Ill i,_| Cetappareil dolt _tre correctementmis a la terre.Consulter(<Mise a terre durefrigerateur _,page7.

Ifyou received a damaged product, you should

immediately contact your dealer or builder. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GEAppliance Warranty. See the Owner's Manual

for wa rranty information.

ForMonogramlocal service ill yourarea,

1.800.444.1845.

ForMonogramService in Canada,

1.888.880.3030.

ForMonogramParts and Accessories,call

1.800.626.2002.

Dueto the weight and size of this refrigerator, and

to reduce the risk of personal injury or damage to

the product -THREE PEOPLEAREREQUIREDFOR

PROPERINSTALLATION.

_,cause du poids et de la taille de ce refrigerator et

pour r_duire le risque de blessure et de dommages,

IL FAUTTROISPERSONNESPOURFAIRE

L'INSTALLATIONCORRECTEMENT.

• Usethis appliance only for its intended purpose.

• Immediately repair or replace electric service

cords that have become frayed or damaged.

• Unplug the refrigerator before cleaning or making

repairs.

• Repairsshould be made by a qualified service

technician.

• II nefaut utiliser cet appareil que pour I'usage

pour lequel il a 6te construit.

• II faut rGparerou remplacer immediatement tout

cordon d'alimentation 61ectriqueeffiloch6 ou

endommag&

• D_brancher le rGfrig_rateur avant le nettoyage ou

toute intervention.

• Les rGparations doivent _tre faites par un

technicien qualifi&

Contents

DesignInformation

Flushor Semi-FlushEnclosure Installations ........3

Enclosure Cutoutand Product Dimensions .....3,4

Accessory Grille Panel Kits.....................................4

Installation Examples...........................................4, 5

Product Dimensions .................................................5

InstallationPreparation

Clearances .................................................................6

Electrical and Water Connection Location ..........6

Groundingthe Refrigerator .....................................7

Tools Required...........................................................8

Materials Required...................................................8

Hardware Supplied ...................................................8

Hardware Recommendations .................................8

Flooring .......................................................................8

Step 1:RemovePackaging ......................................8

InstallationInstructions

Step 2:Install Water Line.........................................9

Step 3:Install Side Panels.....................................10

Step 4:Install Anti-Tip Brackets ...........................10

Step 5:Level Refrigerator ......................................11

Step 6:Optional Anti-Tip Precaution ...................11

Step 7:ConnectWater Supply..............................12

Step 8:Connect Power ..........................................12

Step 9:Mount TopGrille Panel .............................12

Step 10:Adjust DoorAlignment ..........................13

Step 11:Install Toekick...........................................13

Step 12:SetTemperature Controls ......................13

Step 13:Start Icemaker .........................................13

ProblemSolving ......................................................13

ZUGSSUnifiedGrille Panel Kit..............................14

Advance Planning

Design Infi)rmation

36" Stai*_le,s,_ Steel R_fi'ig'erator,s, t;reezer,s

Flush or

Semi-Flush

Enclosure

Installations

True FlushInstallation

In aflush installation,

the refrigerator door

will align evenly with the front

face of adjacent cabinet doors.

The refrigerator blends into the

surrounding cabinetry.

Monogram built-in refrigerators and freezers can be

installed flush with typical 24-3/4"deep cabinetry.

When installed semi-flush, the case trim will conceal

slight gaps around the enclosure. The refrigerator will

project forward approximately 3/4" beyondthe front

face of surrounding cabinetry.

Semi-Flush Installation

These refrigerators

can also be installed

semi-flush into an enclosure

using the minimum cutout

width. The case trim creates a

frame around the opening.

Side Panel Requirements:

• Side panels are not required whenever the

refrigerator or freezer is installed into an enclosure

or between pantry and oven cabinets.

• Side panels are required whenever the sides of the

product are exposed.

• Side panel sizes vary depending on the type of

installation being made.

To accomplish an attractive installation, you must:

1. Determine the need for side panels.

2. Determine side panel thickness.

3. Order matching side panels from the cabinet

manufacturer. Be sure to provide the exact dimensions.

Enclosure

Cutout and

Product

Dimensions

• To achieve a flush fit, the finished cutout width must be

at least 36" wide.

• In a semi-flush installation, the finished cutout must be

35-1/2".

• The electrical and water locations must be located

as shown for either type of installation.

35" 24-3/4"

Case _Case

_ Width|Depth

2G3/4"_36" Frame to

Including

Tubular

Handles

84 .+_

Frame

_Shipped at 84" installation height.

Can be adjusted to 83-1/2"

or 84-1/2" with grille panel kits.

_r _Finish_ Width

'I_ _/_ Electrical

_5,,_6,, Area

841/2" max - 243/4" Total

83 1/2" rain Depth

Finished

Opening

31/2"

WallView

75" FromFloor

to Bottom

of Electrical

Area

'36" for aflush installation.

35-1/2" Min. for a semi-flush installation.

NOTE:Additional cutout width may be required when side

panels are used. Add side panel thickness to the finished

cutout to calculate rough-in width. See installation examples

onthe following page.

Design Infi)rmation

36" Slair_le,v_ Sl_,d R@'ig'_,ralor,s, Fre_,z_,r,s

Side By Side

Installation

Of Freezer

And Refrigerator

841/2"max

831/2"min

Finished

Opening

31/2"

Fora complete food storage center, install a Monogram

Freezerand Refrigerator side byside. For even more

capacity,installtwo refrigerators and oneortwo freezers.

• Order ZU6SS Unified 6rille Panel Kit for one

continuous stainless steel grille panel.

• Electrical and water locations must be located as

shown for either type of installation. A separate

115V,6OHz,20 amp power supply is recommended

for each product.

*FinishedWidth

_21/2"

"JF_Electrical_ _281/2"_

• _-4" 6q. •

5" 5"

243/4"Total

Depth

Freezer

Refrigerator

WallView

75"FromFloor

toBottom

ofElectrical

Area

'72" min. far aflush installation

71-1/2" min.for a semi-flush installation

NOTE:Additional cutout width may be required when side

panels are used. Add side panel thickness to the finished cutout

to calculate rough-in width. Seeinstallation examples below.

Accessory

Grille Panel

Kits

These models arefactory set for 84"installation height.

Adjustments to 83-1/2"or 84-1/2"heights can be made

bychanging the grille panel.

OrderZGCSS36RH(right hand) or ZGCSS36LH(left

hand) 6rille Panel Kit.These kits include 2 grille panels,

for 83-1/2"and 84-1/2"installation heights.

ZUGSSUnified Grille Panel Kit

Forside by side installation, order ZUGSSgrille panel

kit. This kit provides one continuous panel to span the

width of two products installed together for aunified

appearance.

Installation

Examples

Side panels are required whenever the sides of the

product will be exposed.

1/2"to 3/4"side panels are normally set into place and

fastened to adjacent cabinetry or to the back wall before

rolling the refrigerator or freezer into the opening.

Therefore, the rough-in dimensions must allow for

side panel thickness. In both aflush and semi-flush

installation, the finished dimension (the width of

the opening after side panels are installed) must

accommodate the full width of the product.

See page 10for side panel sizes.

Installation

Between

Base and

Wall Cabinets

Refrigerator or Freezer

1/4"ThickII I

SidePanels ! I

FinishedDb .

Rough-InDim. _36" I

NOTE:1/4"thicksidepanelscanbeinserted

intothe ease trim, making the rough-in the

sameasthe outsidetrimwidth:36",

Refrigerator_

Refrigeratordoor\

Cabinet

Design Infi rmation

36 " Stair_l_,ss Ste_,l I?_fi'ig'_,rators, Freezers

Installation

At End-of-Run

RefrigeratororFreezer

RefrigeratorandFreezer

installedside-by-side

I 1/2"Thick[I I

FioishedOim

Roughed-InDim._3T'_

II 1/2"Thick [I I

II I

FinishedDim _L[_]

Rough-InDim. i 73"_

Cak

Refrigerator_

Cabinet

Refrigeratordoor

NOTE:1/2"thick side panels shown.

Side panels can be anythickness.

Add side panel thickness to outside

trim width, (36" or 72"for two models)

to calculate the rough-in dimension,

The leading (front) edge must be

finished to match surrounding

cabinetry.

Frameless

Cabinets

Side panels, 1/2"minimumthickness are required when

using frameless cabinets. The side panel acts as a

spacer between the cabinet and the case trim and

prevents interference with cabinet door swing.

The leading (front) edge must befinished to match

surrounding cabinetry.

1/2"To3/4" SidePanels.L

EdgeFlushWithCabinet

_ Cabinet_,

_) Refrigeratordoor\

Product

Dimensions

ZIRS36NRH,Refrigerator

ZIFS36NRH,Freezer

Handleon the left side, the door swings left to right.

ZIRS36NLH,Refrigerator

ZIFS36NLH,Freezer

Handle onthe right side, the door swings right to left.

Refrigerators are much heavier at the top than at

the bottom - be extra careful when moving.

Les r6frig6rateurs sent beaucoup plus Iourds en

haut qu'en bas. II faut _tre prudentlors des

d6placements.

10-3/4"Max.

10"Miu.

_ 24-3/4"--

-- 35"Casef

-- 36"Overall

84-1/2"Max.

83q/2" Min.

Installation Preparation

36 " Slai_le,_,s Steel I?_fi'ig'e*'alo*',s, tcfeezer,s

Clearances

Min.to

130° Door Wall

Swing

130° ,,y

90° DoorSwing

___ il

,, i

',, Jj36-3/4"

4"_Min.

to Wall

Factory set for a 130°door swing. Order WX14X99

adjustable door stop to reduce swing to as little as90°.

When Installed into a corner:

Allow 25"for afull 130°door swing. Allow 15"for pan

removal. Allow 4" min. clearance when door swing is

adjusted to a 90° opening for pan access, but pan

removal is restricted.

0 _

--25"--

Min. to

Wall 130° Door 130° Door

Swing Swing

,,1 I I

// //

/ / "_x

"--- ......... J/

Min.to

Wall

[,,

,,,,,:,

"'-_ ......... JJ

ClearancesforMultiple Single DoorInstallations

In aside-by-side installation of aleft and right door

swing product, no clearance between the units is

required. OrderZUGSSStainless Steel Unified Grille

Panel Kit for one continuous grille panel.

_15%

J"_ ')',

'\ \,

",\',_),, ',\,

........ ;\_>-".............

Clearances for two productsinstalled side-by-side

with the same(left or right)doorswing

Allow 2"minimum clearance between the products to

prevent door swing interference. Order the WX14X99

adjustable door stop to reduce the factory set 130°

door swing. Allow 15"minimum to a wall to achieve

full drawer extension and pan removal.

NOTE:ZUGSSGrille Panel Kit will net fit this installation.

I',,/I [

',""7" I

I" ,,f\ \,, /

,, I \ ,,

/ I \ ,, //

",, , ,,',,' \,'\, /

Clearances for two productsinstalled side-by-side

with rightand left side hingestogether

Allow 5"minimum between the two products to prevent

one door from striking the other. Use the WX14X99

adjustable door stop to reduce the factory set 130°

door swing andto allow pan removal.

NOTE:ZUGSSGrille Panel Kit will net fit this installation.

Electrical

and Water

Connection

Locations

The water line can be routed through the floor or

back wall.

• The icemaker water line should be:

-Approximately 3-1/2" from the floor on the back wall,

or 3-1/2"from the back wall onthe floor.

-At least 5"from either side of the opening.

A 115volt, 60Hz 15or 20 amppower supply is

recommended. An individual properly grounded

branch circuit or circuit breaker is recommended,

asnoted on the rating plate.

• Locate the electrical outlet within 5"x 6" shaded area

shown.

-2-1/2" from the left side.

Between 75"and 81"from the floor.

IMPORTANT:To insure aflush fit and access to the

power cord, locate the electrical outlet as shown.

ElectricalOutlet

Location2 1/2"

31/2,u

6 '_

//////////////////////_

WaterLocation X

75"

Installation Preparation

36 " ,Stai_le,s,s ,Ste_,l I_fi'ig'_,*'ato*',s, t;*'eeze*',s

Grounding the

Refrigerator

IMPORTANT- (Please read carefully)

FORPERSONALSAFETY,THIS APPLIANCEMUST BE

PROPERLYGROUNDED.

The power cord ofthis appliance is equipped with a

3-prong (grounding) plug that mates with astandard

three-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazardfrom this appliance.

Havethe wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

IMPORTANT:

We recommend two separate 115V, 60Hz, 20 amp

properly grounded electrical outlets for a side by side

blstallation of two products. Each electrical outlet should

have a voltage rating that matches the rating plate.

UseofAdapter plug

Because of potential hazards under certain

conditions, we strongly recommend against use of

an adapter plug. However, if you still elect to use an

adapter,where local codes permit, aTEMPORARY

CONNECTIONmay be made to a properly grounded

2-prong wall outletby use of aUL listed adapter

available at most hardware stores.

The larger slot in the adapter must be aligned with the

larger slot in the wall outlet to provide proper polarity

in the connection of the power cord.

DONOT,UNDERANY CIRCUMSTANCES,CUT OR

REMOVETHETHIRD (GROUND)PRONGFROMTHE

POWERCORD.

When disconnecting the power cord from the adapter,

always hold the adapter in place with one hand and pull

the power cord with the other hand. If this is not done,

the adapter ground terminal is very likely to break with

repeated use.

Should the adapter ground terminal break, DONOTUSE

the appliance until a proper ground has again been

established.

Use of Extension Cords

Because of potential safety hazards under certain

conditions, we strongly recommend against the use of

an extension cord. However, if you still elect to use an

extension cord, it is absolutely necessary that it be a

UL listed, 3-wire grounding type appliance extension

cord having a grounding type plug and outlet, and that

the electrical rathlg of the cord be 15amperes

(minimum) and 120 volts.

FICHED'ADAPTATION

(Fiches d'adaptation non permises au Canada)

Attaching the adapter ground terminal to awall

outlet cover screw does not ground the appliance

unless the cover screw is metal, and not insulated,

andthe wall outlet is grounded through the house

wiring. Youshould havethe circuit checked by a

qualified electrician to makesure the outlet is

properly grounded.

Installation Preparation

36" Slai _less St eel R_/?ig'era lots, Ffeezer,s

Tools

Required

• ]qnsnips to cut banding

• Stepladder

• Bucket

• Level

• 1-1/4"open-end wrench

• Appliance hand truck

• Tubing cutter

• 7/16" open-end wrench

• #2 Phillips screwdriver

• Stubby Phillips screwdriver

• Drill and appropriate bits

• 7/16"socket with 3" extension for

ratchet

• Safety glasses

Materials

Required

• 2x4,35"long, for Anti-]qp support, see page 10

• Stick-on hook and loop fastener strips for 1/4"side panels

• 1/4"copperwater linetubing or 6E SmartOonnectTM TubingKit

• Water shut-off valve

• Screws to secure refrigerator to cabinetry

Hardware

Supplied

•1/4-1/4union with nuts

•Anti-tip mounting brackets

Hardware - Water shut-off valve

Recommendations • Water filter WR97X0214

Flooring For proper installation, the refrigerator and freezer must

be placed on a level surface of hard material that is at

the same height as the rest of the flooring. The floor

mustbestrong enoughto support a fully loadedproduct,

or approximately 1,200Ibs.

NOTE:Protect the finish ofthe flooring. Cuta large

section of the cardboard carton and place underthe

product where you are working.

Step 1

Rem o tie

Packaging

Refrigerator is much heavier atthe top than at the

bottom - be careful when moving. When using a

hand truck, handle from side only.

Ler_frig@ateur est beaucoup plus Iourd en haut

qu'enbas. IIfaut _tre prudent lots desdeplacements.

Siun diane est utilis6,ilfaut soulever ler_frig_rateur

sur le c6t_ seulement.

• Removeouter carton.

-Carefully cut banding at the top and bottom.

• Slide out back corner posts (2).

• Slide carton off top of cabinet.

• Removestyrofoam padstaped to base cabinet.

NOTE:IT IS NOTNECESSARYTO LAYCABINETDOWN

IN ORDERTOREMOVESKID!

• The unit is secured to the skid with 3slotted tie-down

straps. First remove the 5/16"bolts from the base

channels in the tie-downs, then remove the 7/16"bolts

securing the straps to the skid.

• Protect the flooring. Cut a large piece of the card-

board carton and place underthe product where you

are working.

• Support blocks on the bottom must be removed before

the refrigerator is taken off the skid or damage will

occur. Removesupport blocks by carefully tilting

cabinet to side and sliding out.

• Liftthe refrigerator off the skid with an appliance

dolly. Handle from the sides.

'Bolt

DONOTATTEMPTTO ROLLUNIT OFFSKID.

ILNE FAUTPASESSAYERDEFAIREROULERLE

REFRIGERATEURPOURL'ENLEVERDELAYPALETTE.

Installation

Step 2

Install

Freezer

Water Line

• A cold water supply is required for automatic

icemaker operation. Thewater pressure must be

between 20 and 120p.s.i.

• Route 1/4"ODcopper or 6E SmartConnect:Mtubing

between house cold water line andthe water

connection location.

• Tubing should belong enoughto extend to the front

ofthe freezer. Allow enough to accommodate bend

leading into the water valve.

NOTE:The only BEapproved plastic tubing is supplied

in the BESmartConnectTM Refrigerator Tubing Kits.

Do not use any other plastic water supply line because

the line is under pressure at all times. Other types of

plastic may crack or rupture with age and cause water

damage to your home.

BESmartConnectTM Refrigerator Tubing Kits are

available in the following lengths:

2' (0.6m)WX08Xl0OO2

6' (1.8m)WX08Xl0OO6

15'(4.6m) WX08X10015

25'(7.6m) WX08X10025

Shutoff the mainwater supply

Turn on the nearest faucet long enough to clear the line

ofwater.

Install a shut-off valve between the icemakerwater

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

NOTE:Saddletype shut-off valves areincluded in many

water supply kits.Beforepurchasing,makesure asaddle

type valve complieswith your localplumbingcodes.

• Install optional water filter in the water line near the

freezer. Awater filter is recommended in areas where

water supply contains sand or particles. Installation

instructions are packed with the filter.

Floor

TubingJ

NOTE:Commonwealth of Massachusetts Plumbing

Codes2480MR shall be adhered to. Saddle valves are

illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Installation

Step 3

Install

Side Panels

• Side panels are required whenever the sides of the

product will be exposed and when installed between

frameless cabinets. See pages 3and 4.

• Side panels are not required when installed into an

enclosure.

• Side panel installation will be determined bythe

design of the side panelyou have previously chosen.

• Side panels must be installed plumb.

Illustration A

1/4" SidePanels-

Insert end ofside

panel into casetrim.

23-9/16"

84" _F2-9/16"

TopView

Standard4"hightoekickortrimto fit.Height

mayvarydependingonapplication.

• If you choose to use 1/4"side panels, they should be

inserted into the case trim as illustrated. Fastenthe

panels to the product with stick-on hook and loop

fastener strips before setting in place. See

illustration A.

• 1/2"to 3/4"side mnels are normally set into place and

fastened to adjacent cabinetry or the back wall before

rolling the product into the opening. See illustration B.

IllustrationB

1/2"to3/4" Side

Panels- Leading

edgeofsidepanelis

flushwithcabinet

front.Fastentothe

backwallusinga

cleat.

TopView

24-3/4"

T 3_3/4"

Standard 4" high toekick or trim to fit.

Height mayvary dependingonapplication.

Step 4

Install

Anti-Tip

Brackets

] 0

ANTI-TIP PRECAUTIONS

Therefrigeratoris top-heavyandmustbe secured

to preventthe possibilityoftippingforward.

PRECAUTIONSCONTRELESBASCULEMENTS

Le refrigcrateur est beaucoupplusIourd en haut

et il faut le maintenir en place poureviter la

possibilite de sonbasculementvers ravant.

• Cut a2"x 4"x 35"block and secure the block to

the mounting brackets provided using #12or #14wood

screws.

• Secure the bracket with wood block to the back wall

so that it is 84"(or your installation height) from the

finished floor. Use #12or #14wood screws. See

illustration.

• Screws must penetrate atleast one inch into vertical

wall studs.

• Before pushing the refrigerator into the opening, plug

the power cord into the receptacle. Openthe grille

panel and reach into the opening atthe back to grasp

the power cord. Pullthe power cord into the opening

asyou push the refrigerator back.

• 6ently push refrigerator into the opening with hands

against front corners.

Brackets

Required

Height

From

Floor

Bottom

ofWood

Block

SideView

Brackets

NotRequired

Beneatha

Soffit

2x4 CutJ

35"Length

Installation Mounting

Height Bracket

FromFloor

ScrewsMountedintoJ

VerticalWall Studs

IMPORTANTNOTE:Whenthe refrigeratoris installedundera soffit

or ifthere isnotenoughheightfor this methodofsecurity,brackets

cannotbeused.Proceedto step5to levelthe refrigeratorandthen

to step6to securerefrigeratorto cabinets.Therefrigeratormustbe

securedtopreventtipping.

Installation

36" Slai_le,s,s S/er./I_/?it_'eralr.',s, Frrwzer,s

Step 5

Level

Refrigerator

These products have a4-point leveling system. The

front is supported byleveling legs, the rear is supported

bywheels.

• Adjust rear wheels beneath the product to just barely

touch the 2x4 block.

• Turn the 7/16"hex out located abovethe front wheels.

Turnto raise or lower.

• Forfront leveling legs, use a 1-1/4"open-end wrench.

• Adjust carefully; the product should be level and

plumb with cabinetry, and should align with toekick

height.

HexNutAdjusts_==_=_==_11 I

RearWheels )[_]1 I

o ZOo o

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1".If the

installation requires more than 84-1/2"height, the

installer should elevate the refrigerator on a sheet

of plywood or runners. Cabinetry trim could also be

added across the top of the opening to shorten the

opening. If youattemptto raisethe refrigerator more

than 1",you will damagethe frontleveling legsand

rear leveling wheels.

Les roues de nivellement arriere et les pattes de

nivellement avant permettent un r6glage maximal

de 25 mm(1 po).Si I'ouverture pour le r_frig_rateur

a une hauteur sup_rieure _2,15m (84-1/2po),

I'installateur dolt _lever le r_frig_rateur sur une

feuille de contre-plaqu6 ou des glissi_res. IIest

_galement possible d'ajouter des baguettes de

finition des placards sur le haut de I'ouverture afin

de la r_duire. Leverle refrigerateur de plusde 25mm

(1 po)endommageles pattesde nivellemeet avant

et les rouesde nivellement arriere.

Step 6

Secure

Product

to Sides

NOTE:Whenever possible, perform

this step for additional anti-tip

security. This step can be used as

an alternate to Step 4,Anti-Tip

bracket installation, whenever

brackets cannot be used.

_] Refrigerator

Stud__ Cabinet \

ooo-V

When using 1/2"to 3/4" side panels, the front flange of

the case trim is attached to the side panel.

• Opendoor to access case trim.

• Brill hole in trim below interior opening. Brive screw

through trim and side panel.

• Follow the same procedure on opposite side.

If installed between cabinets with no side panels or in

a custom enclosure, install a spacer block asshown.

• Opendoor to access case trim.

• Brill hole in trim below opening. Brive screw through

trim and into block.

• Follow the same procedure on opposite side.

]]

Installation

36 " Slai_lr_ss Steel I_e[)'i£'eralr_rs, Ffr_ezers

Step 7

Connect

Freezer

Water Supply

• Locate and bring tubing to the front of the cabinet.

• Turn the water on to flush debris from the line. Run

about aquart ofwater through the tubing into a

bucket, then shut off water.

CopperTubing:

• Slip a 1/4"nut and ferrule (provided) over both ends

ofthe copper tubing. Insert tube into the unionfitting

on the unit and tighten nutto union.

• Turn on the water to check for leaks.

GESmartConnect"Tubing:

• Insertthe molded end of the tubing [ntothe

refrigerator connection. Tighten the compression

nut until it is just hand tight.

• Tighten one additional turn with awrench.

Overtightening can cause leaksE

• Turn on the water to check for leaks.

NOTE:Make sure excess tubing length does not

interfere with toekick installation.

Step 8

Check Power

• Checkto makesure power is on byopening the door

to see if interior lights are on.

Step 9

Mount Top

Grille Panel

Forshipping purposes, the top case trim is secured at

84"installation height.

Toraise casetrim to 84-1/2"installation height orto

lower case trim to83-1/2":

• Loosen2screws oo both sides and raise or lower the

top case trim to meet soffit height or to the top of

adjacent cabinets.

• Tighten all 4screws.

• Mount the grille panel bydropping into slots on the

case trim.

The grille panel assembly is factory set for an 84"

installation height. If installation height is 83-1/2"or

84-1/2",order ZGCSS36RH(right hand) or ZGCSS36LH

(left hand) grille panel kit.

TopCaseTrim

Installation

Height

IMPORTANT:Maintain 1-1/2"min. gap between top of doors and

bottom of grille panel.

Installation

Step 10

Adjust Door

Alignment

Check door alignment. Thetop ofthe door should be

parallel with the grille panel. If the door appears to be

too high ortoo low on the handle side, adjustments

can be made by turning the hinge.

• To raise the door,turn adjustable hinge pintoward

the right.

• Tolower the door,turn hinge pin toward the left.

Turnthe hinge pinwith a 5/16"wrench or, on some

models, usethe 3/16"Allen wrench taped to the hinge.

!_ DoorShouldbeParallel

With GrillePanel

5/16"Wrench

Step 11

Install

Toekick

• A standard toekick is supplied. Install with 2screws

provided, adjust to desired height and tighten screws.

IMPORTANT:The vented toekick must remain

unobstructed for proper air circulation and operation.

Step 12

Temperature

Controls

• Set temperature control at "5".

IMPORTANT:Allow 24 hoursfor temperatures to stabilize

before making adjustments.

Step 13

Start

Icemaker

• Start the switch to I (on).The green light will come on

andthe icemaker will begin operation automatically.

• Be sure nothing interferes with the sweep of the

feeler arm.

• Discard the first few batches of ice cubes.

• Toturn the icemaker off, set the switch to O(off).

Allow 45 minutes for the icemaker to resume

operation.

'GreenPowerLight

Problem

Solving

Operationof Refrigeratorand Freezer

If the product does not operate after checking the

installation instructions:

• Checkto be sure power cord is plugged in the wall

outlet.

• Checkto be sure that fuse or circuit breaker is

turned on.

If any of these problems persist:

Callfor Monogram local service in your area,

1.800.444.1845.

Cleaning the Stainless Steel Exterior

Stainless Steel has some unique cleaning

characteristics. In order to keep your refrigerator or

freezer looking like new, we suggest cleaning it with

Stainless Steel Magic or asimilar product.

Stainless Steel Magic is available at Ace, True Value,

Home Depot,Servistar, HWI and other leading stores.

It is also available through 6E Parts by calling

1.800.626.2002.Order part number WX10X15.

Z _ _

U(,SS Trim Kit

Un!/_ed Stainless Steel Custom Grille P_nel

Tools and Materials Required:

• #1 and#2 Phillips screwdrivers or sockets

• 1/4"angled wrench and 1-1/2"open ended

wrench

• Drill and appropriate bits

• Customgrille panel

• Safety glasses

• Glovesto protect against

sharp edges

CompletionTime:Allow approximately 3hours to install

this kit.

IMPORTANT:2 People are required to install this kit.

CAUTION: Disconnect power before you begin.

PartsList:

A. Soffit VentTop F

B.Left Side CaseTrim --_:/- _._ _ __ _

C.Right Side CaseTrim __ _ _

D.Center U-ShapeTrim _

E.Grille Base Wrap

F. Stainless Steel Unified Panel

G.FoamSpacer Pads

Step 1

Install

Spacer Pads.

Replace

Side Case Trims

CAUTION: Handle parts with care to avoid scratching.

In aside by side installation, the inside case trim of both

products will be removed andreplaced with ashorter

trim.

• Lift upto removethe supplied grille panel assembly on

both products. Discard both assemblies.

• Apply the supplied foam spacer pads to the mating

side of one product as shown.

• Removethe Phillips head screws from the inside case

trim of each product as shown. Removeand discard

side trim. Retain screws.

• Install new side case trim with notches toward the

bottom. Install with original screws.

ZUGSS Trim Kit

U_!/ir'_! Slainlr,,s,s Sled G*'ille Panel

Step 2

Install

Anti-Tip

Brackets

ANTI-TIP PRECAUTIONS

Theseproductsare heavyat the topand mustbe

securedtopreventthe possibilityof tippingover.

Brackets Brackets

Required NotRequired

Beneatha

Soffit

PRECAUTIONSCONTRELESBASCULEMENTS

Le refrigerateur est beaucoupplusIourd enhautet

il faut le maintenir enplace poureviter la possibilite

de son basculementvers I'avant.

• Cut a 2"x4"block, 71"long. Secure the 2"x4"to the 4

mounting brackets provided using #12or #14wood

screws.

• Secure the brackets with wood block to the back wall

sothat it is 84"(or your installation height) from the

finished floor. Use#12or #14wood screws. See

illustration.

• Screws must penetrate at least one inch into vertical

wall studs.

Roll BothProductsinto Opening

• Gently push each product into opening with hands

against front corners. Push back into the opening until

it isflush orsemi-flush with adjacent cabinets.

SideView

2 x 4 Cutj._r-

71" Length

Installation Mounting 5:'-"--

Height Bracket

FromFloor

ScrewsMountedinto_'

VerticalWall Studs

IMPORTANT NOTE:When the products are installed under

a soffit or if there is not enough height for this method of

security, use Step4as analternative. The refrigeratorand

freezer must besecured to preventtipping.

Step 3

Level Both

Products

BothproductsMUST BE LEVELAND PLUMB with each

otherand adjacentcabinetryon each side. Toekick

heights should align with cabinetry.

• Adjust carefully. Both models have4-point leveling.

The front is supported by leveling legs, the rear is

supported bywheels.

• Raise units to the same level, aligning with adjacent

toekick heights.

• Adjust rear wheels beneath the product to just barely

touch the 2x4 block.

• Turnthe 7/16"hex nut located above the front wheels

to raise or lower the back ofthe refrigerator.

• Toadjust the front leveling legs: Use a 1/4"angled

wrench to turn the top of the leveling leg, or turn the

bottom of the legs with a 1-1/4"wrench.

H_xNrU_vAdeJ_SstS_ II

Unitsmustbe 1"apart andevenly aligned attop and

bottom.The inside case trims must align,top and

bottom.

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1".If the

installation requires more than 84-1/2"height, the

installer should elevate the refrigerator on a sheet

of plywood or runners. Cabinetry trim could also be

added across the top of the opening to shorten the

opening. If youattempt to raisethe refrigerator

more than 1",youwill damagethe front leveling

legs and rear leveling wheels.

Les roues de nivellement arriere et les pattes de

nivellement avant permettent un rGglage maximal

de 25 mm (1 pc). Si I'ouverture pour le r_frig_rateur

a une hauteur sup&ieure _ 2,15 m (84-1/2 pc),

I'installateur dolt _lever le r_frig_rateur sur une

feuille de cootre-plaqu6 ou des glissi_res. II est

_galement possible d'ajouter des baguettes de

finition des placards sur le haut de I'ouverture afin

de la r_duire. Lever le refrigerateur de plus de 25 mm

(1 po) endommage les pattes de nivellement avant et

les roues de nivellement arriere.

ZUGSS Trim Kit

U*_!fir,d Stai_zless Steel G*'illr, Pa_el

Step 4

Secure

Products

To Sides

NOTE:Thisstep can be used as

an alternative to Step 2,Anti-Tip

bracket installation, whenever

brackets cannot be used.

Whenever possible, perform

this step for additional anti-tip

security.

When using 1/2"to 3/4"thick side panels, the front

flange of the case trim is attached to the side panel.

• Opendoor to access case trim.

• Drill hole in trim slightly below the interior opening.

• Drive screw through the trim and into the side panel.

• Follow the same procedure onthe opposite outside

product trim.

_/ Refrigerator \

Stud_Cabinet \

OR _

If the product is installed between cabinets with no

side panels or into a custom enclosure, install aspacer

block asshown.

Step 5

Install Center

Trim Strip

• Open doors fully.

• Starting at the top, presstrim strip over inside case

trims of both products.

• Continue pressing trim until you reach the bottom of

the case trims. Thetrim will align with the top and

bottom of the case trim.

CaseTrim

U-Shape

Trim

Step 6

Remove

Wire Fence and

Switch Cover

• Remove3screws holding the wire fence on both

products. Retainfences and all screws.

6rille Base Cover

• Lift off grille base covers. Discard covers.

ZUGSS Trim Kit

U_z!/_ed Staitzless Steel G*'ille Pa_zel

Step 7

Install

Grille Base

Cover

UnifiedBaseCover Place

TrimOver

Hinges

• Opendoors fully.

• Install the double width grille base cover by slipping

the notched ends over the hinges.

Install Install

3Screws 3Screws

• Place wire fence over the grille base cover (textured

side out). Drive original wire fence screws through the

fence, the grille base cover andinto the frame.

Step 8

Remove

Grille Frame

emove

• Back out 2screws on each side of the top case trim.

• The top piece is secured to the unit with a rubber dust

gasket. Rollthe trim upward to access and remove

endscrews as shown. Removeand discard inside

pieces.

• Slide assembly out ofthe rubber gasket.

Dust

6asket

Remove

Screws

ZUGSS Trim Kit

Un!/ied Stainless Slcel Grille Panel

Step 9

Install

Soffit

Vent Top

SlipDustGasket

IntoTrimOnOneEnd

Slip Second Dust

Gasket Into Trim

• Separate the top and hinge side trim pieces by

removing side screws. Discard top piece; retain

screws.

• Install one end piece to unified top piece with

2 original screws.

• Slip endof rubber dust gasket into end of top unified

piece and slide trim towards the center. Engagethe

second piece of gasket and continue sliding trim until

evenwith opposite ends.

• Reinstall end pieces to case trims. Pushtop piece up

against soffit or to installation height. Tighten screws

on both sides.

• Whenever possible, place a level on the top trim.

Adjust side trims until entire grille frame is level.

Screws

Step 10

Mount

Unified

Grille Panel

• Mount the unified grille panel by dropping into slots on

the outside case trim.

ZUGSS Trim Kit

Un!fied Stainless Steel Grille Panel

Step 11

Adjust

Door

Alignment

Check door alignment. The top of the door should be

parallel with the grille panel. If the door appears to be

too high ortoo low on the handle side, adjustments can

be made.

• Use a5/16"wrench to turn the hinge.

• To raise the door, turn adjustable hinge pin toward

the right.

• To lower the door, turn hinge pintoward the left.

5/16"Wrench

Pub.No.49-60073-3

PartNo.197D3003PO01

12-03JR

65161-01

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

• ®

I_or 3lo_wg'ram local _'_Jic_, i_ )our area, call

) 5

l. 800.444. l,_4 .

)

Note: t l-Odtl([ ill]pl'O_(_lll(!ll[ is _ COll[illtlillg ell(l(_a'_OF at

(;(n_ ral Electric. Thor(fore, materials, appearance and

spe(ifi(_ltions are su[)je(I to ( h_lllg(! _,_,illlout noli(e.

Monogram:

GEConsumer Products

General Electric Company

Louisville, KY40225

@2003General Electric Company

GE ZIFS36NMGRH Installation guide

GE ZIFS36NMGRH Installation guide

GE ZIFS36NMGRH Installation guide

Related papers

Other documents