Viking Range Center Trim Kit Operating instructions

Viking Range
Brand
Viking Range
Model
Center Trim Kit
Type
Operating instructions
Installation Guide
Built-In Refrigeration Top Grille /
Center Trim Installation
(Dual Installation)
Side/Center Trim Installation -
Professional & Professional Integrated Models
• Remove cabinet side trim mounted on the left hand side of the refrigerator to be installed
on the right side of the installation. Replace with the “Z” shaped side trim provided in the
grille kit.
• For Professional (not including the Integrated line), skip to the next step. Remove cabinet
side trim mounted on the right side of the refrigerator to be installed on the left side of the
installation. Replace with the “J” shaped side/center trim provided in the grille kit.
2
Left Hand
Cabinet Side
Trim
Side/Center Trim Installation -
Professional & Professional Integrated Models
3
Cabinet Side Trim
“Z” Shape
Cabinet Cabinet
Right Hand Door Unit
Left Hand Door Unit
Anti-Tip
Lag Bolts
2x4 mounting board fastened to
wall at top of cabinet opening
• Engage the right hand refrigerator’s left side trim into the “J” shaped portion of the left side
refrigerator’s right side trim.
• Finish unit installation according to installation instructions provided in each unit.
Cabinet Side Trim
“J” Shape
(creates center trim appearance)
Grille Assembly Bracket Placement -
Professional & Professional Integrated Models
4
For 66” grille, excluding Custom Panel, Add/Remove brackets to full length grille as required.
See illustration below.
TOP
Use this bracket if 36” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on left side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 36” W. product is
on left side (facing unit), otherwise
remove.
*NOTE: Depending on unit configuration, two brackets should be removed and discarded. The
72” W. and 60” W. grille assemblies have all four (4) brackets mounted in the proper location.
66” Professional/Integrated Grille (back view)
Grille Assembly Install -
Professional & Professional Integrated Models
5
• Remove center grille blade by lifting up and pulling forward.
• Insert grille into refrigerators. Screw grille assembly into units with (4) screws removed in
Step 3 (See Grille Removal Section).
6
Side/Center Trim Installation -
Designer & Custom Panel Models
• Remove cabinet side trim mounted on the left hand side of the refrigerator to be installed
on the right side of the installation. Replace with the “Z” shaped side trim provided in the
grille kit.
• For Professional (not including the Integrated line), skip to the next step. Remove cabinet
side trim mounted on the right side of the refrigerator to be installed on the left side of the
installation. Replace with the “J” shaped side/center trim provided in the grille kit.
Left Hand
Cabinet Side
Trim
7
Side/Center Trim Installation -
Designer & Custom Panel Models
Cabinet Side Trim
“Z” Shape
Cabinet Cabinet
Right Hand Door Unit
Left Hand Door Unit
Anti-Tip
Lag Bolts
2x4 mounting board fastened to
wall at top of cabinet opening
• Engage the right hand refrigerator’s left side trim into the “J” shaped portion of the left side
refrigerator’s right side trim.
• Finish unit installation according to installation instructions provided in each unit.
Cabinet Side Trim
“J” Shape
(creates center trim appearance)
8
Grille Assembly Bracket Placement -
Designer Models
For 66” grille, excluding Custom Panel, Add/Remove brackets to full length grille as required.
See illustration below.
TOP
Use this bracket if 36” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on left side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 36” W. product is
on left side (facing unit), otherwise
remove.
*NOTE: Depending on unit configuration, two brackets should be removed and discarded. The
72” W. and 60” W. grille assemblies have all four (4) brackets mounted in the proper location.
66” Designer Grille (back view)
9
Grille Assembly Install -
Designer Models
• Remove center grille blade by lifting up and pulling forward.
• Insert grille into refrigerators. Screw grille assembly into units with (4) screws removed in
Step 3 (See Grille Removal Section).
10
Grille Assembly -
Custom Panel Models
On Custom Panel models, grill spacers from original unit grilles must be reused:
• Remove grille brackets from grille included in the grille kit by removing 4 screws on each
grille bracket located on the back of the grille assembly.
• Remove grille brackets and spacers from original unit grilles by removing 4 screws on each
grille bracket located on the back of each grille assembly.
• Install grille brackets and spacers from original unit grilles onto grille from the kit using the
original grille hardware.
Important: The spacers must be oriented on the new grille the
same way they were on the original grille.
Also, remember to install the spacers on the
corresponding side of the installation (if installing a unit on the left side of an installation, its
grille spacers should be installed on the left side of the unified grille.)
11
Grille Assembly Bracket Placement -
Custom Panel Models
For 66” grille, excluding Custom Panel, Add/Remove brackets to full length grille as required.
See illustration below.
TOP
Use this bracket if 36” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on left side (facing unit), otherwise
remove.
Use this bracket if 30” W. product is
on right side (facing unit), otherwise
remove.
Use this bracket if 36” W. product is
on left side (facing unit), otherwise
remove.
*NOTE: Depending on unit configuration, two brackets should be removed and discarded. The
72” W. and 60” W. grille assemblies have all four (4) brackets mounted in the proper location.
66” Custom Grille (back view)
12
Grille Assembly Install -
Custom Panel Models
• Remove center grille blade by lifting up and pulling forward.
• Insert grille into refrigerators. Screw grille assembly into units with (4) screws removed in
Step 3 (See Grille Removal Section).
13
14
15
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-845-4641.
F20549B EN
(011517)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Viking Range Center Trim Kit Operating instructions

Viking Range
Brand
Viking Range
Model
Center Trim Kit
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents