ASO Safety Solutions Plug'n'Sense System Assembly Instructions

ASO Safety Solutions
Brand
ASO Safety Solutions
Model
Plug'n'Sense System
Type
Assembly Instructions

This manual is also suitable for

ASO Safety Solutions Plug'n'Sense System

The ASO Safety Solutions Plug'n'Sense System is a safety-contact-edge system that can be used to create customized safety edges for a variety of applications. The system is designed to be easy to assemble and install, and it can be used to create edges that are either horizontal or vertical.

The Plug'n'Sense System is made up of several components, including:

  • Safety-contact-edge: The safety-contact-edge is the main component of the system. It is a flexible strip that can be cut to the desired length. The edge is made of a durable material that is resistant to wear and tear.

ASO Safety Solutions Plug'n'Sense System

The ASO Safety Solutions Plug'n'Sense System is a safety-contact-edge system that can be used to create customized safety edges for a variety of applications. The system is designed to be easy to assemble and install, and it can be used to create edges that are either horizontal or vertical.

The Plug'n'Sense System is made up of several components, including:

  • Safety-contact-edge: The safety-contact-edge is the main component of the system. It is a flexible strip that can be cut to the desired length. The edge is made of a durable material that is resistant to wear and tear.
1
Assembly Instrucons
Safety-contact-edges may only be assembled and installed by authorized personnel!
1. Cung the safety-contact-edge
The safety-contact-edge is cut 20 mm shorter than the nal length
dimension to allow for the length of the end caps on each end.
Make sure that the safety-contact-edge is cut clean and straight.
2. Preparing end caps
a) Notch for the weather-sealing lip
When assembling safety-contact-edges with weather-sealing lips,
the end caps have to be notched where indicated to allow for the
weather-sealing lip(s).
Markers
c) Water drain plugs
For installaons in contact with water, it is necessary to remove
water drain plugs. If the edge is to be mounted horizontally, remove
drain plugs from both ends. If the edge is mounted vercally, just
remove the lower drain plug.
Water drain plugs
b) Connecon cable
The connecon cable exits the boom of the end cap.
Pre-assembled ASO delivered end cap with contact plug includes:
End cap
Contact plug
Clip
Lock cap
Butyl seal
Contact plug with cable Contact plug with resistor
Cable exit
sidewards
downwards
backwards
cung length = nal length - 20 mm
Final length dimension
(inside)
GE F-Series, Plug‘N‘ Sense System
Assembly Instrucons
2
5. Electrical tesng of the contact edge
6. Cung mounng rail
The mounng rail has to be20 mm shorter than the nal dimension
of the contact edge.
Measure the contact edge with a mulmeter. In rest posion, the
resistance value has to be 8,2 kΩ ± 500 Ω.
When edge is acvated, the resistance should not exceed 500 Ω.
10 mm
4. Put on end caps
Release the contact plug from end cap and then snap in the contact
lock cap on the contact plug unl it clicks into place. Apply pressure
to ensure the end cap plug is fully inserted into the contact edge.
3. Insert the contact plug
- Insert the plug, which is xed to the end cap, into the
electrical switching chamber of the safety-contact-
edge.
- The elasc butyl seal has to be pressed on ght to the
edge (Max. 6,5 mm from plug base to prole)
max. 6,5 mm
15.DB.10.003 Technical data Rev 03 as of October 18th 2012 Technical changes reserved
Please note:
The ambient temperature during assembly of the contact plug to the edge prole should be between 10° and 30° C
at a relave humidity between 40% and 70%.
GE F-Series, Plug‘N‘ Sense System
Assembly Instrucons
electrical switching
chamber
Am Grarock 8 • D-33154 Salzkoen
www.asosafety.com • e-mail: info@asosafety.com
ASO GmbH excludes all liability for damage caused as a result of an incorrect assembly and installaon of the
contact edges.
  • Page 1 1
  • Page 2 2

ASO Safety Solutions Plug'n'Sense System Assembly Instructions

ASO Safety Solutions
Brand
ASO Safety Solutions
Model
Plug'n'Sense System
Type
Assembly Instructions
This manual is also suitable for

ASO Safety Solutions Plug'n'Sense System

The ASO Safety Solutions Plug'n'Sense System is a safety-contact-edge system that can be used to create customized safety edges for a variety of applications. The system is designed to be easy to assemble and install, and it can be used to create edges that are either horizontal or vertical.

The Plug'n'Sense System is made up of several components, including:

  • Safety-contact-edge: The safety-contact-edge is the main component of the system. It is a flexible strip that can be cut to the desired length. The edge is made of a durable material that is resistant to wear and tear.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents