2. Transmitter
  3. iGAZEREKIT-UL
iGAZEREKIT-UL

Transmitter iGAZEREKIT-UL Product information

  • Hello! I am an AI chatbot trained to assist you with the Transmitter iGAZEREKIT-UL Product information. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the Transmitter Solutions iGAZEREKIT-UL?
    What components does the kit include?
    How should the kit be connected to a DoorKing operator?
    What is the function of the 10kΩ resistor?
    What is the purpose of the Test C?
    What is the role of the NO and NC contacts?
    Can multiple kits be connected to a single DoorKing operator?
    Where can I find more information about the kit?
UL 325 Terminal
Safety Device Wiring Manual
Closed Gate
Wall / Fence Close Beam
Entrapment Area
Ground (Common): Common terminal for all MONITORED entrapment protection device inputs.
2, 4, 6, 8 & 10
OPEN BEAM
iGAZE: R50LR-UL, R32P-UL
SR66HD, or SR33HD
123 4 567
12- 30V DC/AC 60 Hz
NC
NC
NO
COM
TP1
TP2
Non polarity
Dip Switch 1: ON
10kΩ
Resistor
UL 325 Operator Terminal
1
ON
234
UL 325
DIP-Switches
TRANSMITTER SOLUTIONS
PHOTO EYES
TRANSMITTER SOLUTIONS
PHOTO EYES
CLOSED BEAM
123 4 567
12- 30V DC/AC 60 Hz
NC
NC
NO
COM
TP1
TP2
Non polarity
Dip Switch 2: ON
UL 325 Operator Terminal
1
ON
234
UL 325
DIP-Switches
1
Closed Gate
Wall / Fence
Open Beam
Entrapment Area
OPEN Beam Stop: Obstructed opening-direction photo
beam will stop the gate during the opening-direction only.
Gate will resume the open cycle when the obstructed photo
beam has been cleared.
In addition to the inherent reversing sensor system, this operator has a UL 325 terminal for the connection of photo sensors-Type B1
and/or reversing edges-Type B2 entrapment protection required by UL 325 standards. At least ONE external entrapment protection
device MUST be installed or the operator will NOT function. Install these devices where the risk of entrapment or a safety hazard exists,
examples of which are shown below. Specific installations will vary.
3CLOSE Beam Reverse: Obstructed closing-direction
photo beam will reverse the gate to the open position and reset
the close-timer during the closing-direction only. Gate will
close when timer times out.
ON
ON
REVERSE
SENSITIVITY
REVERSE
LOOP
EXIT
LOOP
FULL OPEN
DOORKING
4602-010
SW1
SW3
SW2
OPEN
TIMER
NC
NO
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
1
2
3
4
5
6
7
8
9
10
1
ON
234
1
ON
234
UL 325 Terminal and LEDs
Connect ONLY MONITORED Devices
UL 325 DIP-Switches
115 VAC Convenience
Outlets
1 - OPEN Beam STOP (Switch 1)
2 - Ground (Common)
3 - CLOSE Beam REVERSE (Switch 2)
4 - Ground (Common)
5 - 24 VAC 250 ma. Max
6 - Ground (Common)
7 - OPEN Edge/Beam REVERSE (Switch 3)
8 - Ground (Common)
9 - CLOSE Edge/Beam REVERSE (Switch 4)
10 - Ground (Common)
1 - OPEN Beam
2 - CLOSE Beam
3 - OPEN Edge
4 - CLOSE Edge
WARNING
MOVING GATE CAN CAUSE
Operate gate only when gate area is in sight
and free of people and obstructions.
Do not allow children to play in gate area
or operate gate.
Do not stand in gate path or walk through
path while gate is moving.
Read owner’s manual and safety instructions.
SERIOUS INJURY OR DEATH
CLASS
CERTIFIED TO
CAN/CSA C22.2 NO. 247
CONFORMS TO
ANSI/UL-325
VEHICULAR GATE OPERATOR
HP
53382
MODEL
SERIAL
VOLTSPHASE
AMPS 60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
ON
ON
REVERSE
SENSITIVITY
REVERSE
LOOP
EXIT
LOOP
KEY SWITCH
DOORKING
4602-010
SW1SW2
OPEN
TIMER
NC
1
2
3
4
5
NO
UL 325 LEDs:
LED ON: Connected device has been activated.
LED remains off during normal operation.
LED Flashing: Connected device is in fault.
Wiring to device is bad.
DIP-switches MUST
be turned ON for
each device wired to
terminal.
Monitored Device Note: Only 1 monitored Device can be
connected to each input. An OPTIONAL Expansion Board
(sold separately) will allow connection for additional devices.
External Entrapment Protection Devices:
DOORKING® 9150 - Entrapment and Safety Protection
SW3
DoorKing 4620 18-PIN Main Terminal
iGAZE: R50LR-UL, R32P-UL
SR66HD, or SR33HD
10kΩ
Resistor
Open Beam
Wall / Fence
Filler Post if necessary
Closed Gate
Open Edge
Open Edge
Entrapment Area
Closed Gate
Wall / Fence
Close Edge
Entrapment Area
Close Beam
IGAZEREKIT-UL IGAZEREKIT-UL
Used with permission of DoorKing® Inc. All graphics, language and layouts are
copyright protected by DoorKing® Inc. of Inglewood, CA. DoorKing® assumes no
responsibility for the accuracy of the information provided by Transmitter Solutions.
The Transmitter Solutions products listed have not been trested nor listed by
DoorKing® as being UL Compliant for their system. All testing has been conducted by
Transmitter Solutions.
7OPEN Edge/Beam Reverse: Obstructed reversing
edge or photo beam will reverse the gate to the close position
during the opening-direction only.
• After the gate reverses to the close position, any opening input
will cycle the gate again.
Note: If the gate is opening by a time clock and a edge/beam gets
obstructed, the gate will return to the closed position and another
input (automatic exit loop, reverse loop, remote etc.) is needed to
cycle the gate open again.
9CLOSE Edge/Beam Reverse: Obstructed reversing
edge or photo beam will reverse the gate to the open position
during the closing-direction only.
• After the gate reverses to the open position, the close-timer will
time out and close the gate (if it is turned on).
• If a second sequential obstruction is encountered prior to the
gate reaching the close limit, the gate will reverse to full open
position and enter a soft shutdown condition.
TRANSMITTER SOLUTIONS
iGAZE RE UL 10kΩ KIT
TRANSMITTER SOLUTIONS
iGAZE RE UL 10kΩ KIT
OPEN EDGE
+
C1
12/24
NC1
NO1
C2
NC2
NO2
Test 1
Test 2
Test C
−
Dip Switch 3: ON
UL 325 Operator Terminal
1
ON
234
UL 325
DIP-Switches
CLOSE EDGE
+
C1
12/24
NC1
NO1
C2
NC2
NO2
Test 1
Test 2
Test C
−
Dip Switch 4: ON
UL 325 Operator Terminal
1
ON
234
UL 325
DIP-Switches
/