2. Transmitter
  3. iGAZEREKIT-UL
iGAZEREKIT-UL

Transmitter iGAZEREKIT-UL Product information

  • Hello! I've reviewed the Safety Device Wiring Manual for the DoorKing iGAZE safety device. This document provides detailed instructions on how to wire and install external entrapment protection devices such as photo sensors and reversing edges to ensure safe gate operation. I'm ready to answer any questions you might have about connecting and configuring these safety features.
  • What type of external entrapment protection devices are compatible with this system?
    How many external entrapment protection devices must be installed?
    What should be done with DIP-switches?
    Can we connect more than 1 monitored device to each input?
Safety Device Wiring Manual
Closed Gate
Wall / Fence Close Beam
Entrapment Area
OPEN BEAM
TRANSMITTER SOLUTIONS PHOTO EYES TRANSMITTER SOLUTIONS PHOTO EYES
123 4 567
12- 30V DC/AC 60 Hz
NC
NC
NO
COM
TP1
TP2
Non polarity
Dip Switch 1: ON
10kΩ
Resistor
UL 325
Terminal
UL 325 DIP-Switches
1
Closed Gate
Wall / Fence
Open Beam
Entrapment Area
OPEN Beam Stop: Obstructed opening-direction photo beam
will stop the gate during the opening-direction only. Gate will resume
the open cycle when the obstructed photo beam has been cleared.
In addition to the inherent reversing sensor system, this operator has a UL 325 terminal for the connection of photo sensors-Type B1
and/or reversing edges-Type B2 entrapment protection required by UL 325 standards. At least ONE external entrapment protection
device MUST be installed or the operator will NOT function. Install these devices where the risk of entrapment or a safety hazard exists,
examples of which are shown below. Specific installations will vary.
2CLOSE Beam Reverse: Obstructed closing-direction photo
beam will reverse the gate to the open position and reset the close-timer
during the closing-direction only. Gate will close when timer times out.
External Entrapment Protection Devices:
DOORKING® - Entrapment and Safety Protection
Only 1 monitored Device can
be connected to each input.
An OPTIONAL Expansion Kit
(sold separately) will allow
connection for additional devices.
Common
Full Open
24 VDC
GND
GND
CE
OE
CB
OB
1 2 3 4 5 6
7 8 9 10
1234
ON
CLOSED BEAM
123 4 567
12- 30V DC/AC 60 Hz
NC
NC
NO
COM
TP1
TP2
Non polarity
Dip Switch 2: ON
10kΩ
Resistor
UL 325
Terminal
UL 325 DIP-Switches
iGAZE: R50LR-UL, R32P-UL, SR66HD, or SR33HDiGAZE: R50LR-UL, R32P-UL, SR66HD, or SR33HD
Common
Full Open
24 VDC
GND
GND
CE
OE
CB
OB
1 2 3 4 5 6
7 8 9 10
1234
ON
1234567 8
ON
12345678
ON
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
EXIT
LOOP
REVERSE
LOOP
IN POWER/BATT
PWR
SEL
REV SENSE
JUMPER ON
SOLAR MODE
P3
SELF TEST
RESET
RED=CHARGING
GREEN=CHARGED
KEY
SWITCH
NO
NC
3 BUTTON
CONTROL
SW1
SW2
OFF ON
POWER
P4
P2
61
TIME DELAY
1 2 3 4 5 6 7 8 9 10
1234
ON
OPEN BEAM
CLOSE BEAM
OPEN EDGE
CLOSE EDGE
DIP-switches
MUST be turned
ON for each device
wired to terminal.
1234
ON
OPEN BEAM
CLOSE BEAM
OPEN EDGE
CLOSE EDGE
ONLY connect
monitored devices.
Connect ONLY MONITORED Devices
Ground (Common)
Ground (Common)
CLOSE Edge
OPEN Edge
CLOSE Beam
OPEN Beam
Note:
All safety devices are wired to the
primary operator when using dual
gate operators.
1 2 3 4 5 6 7 8 9 10
UL 325 Terminal
DoorKing 9024 20-PIN
Main Terminal
+
C1
12/24
NC1
NO1
C2
NC2
NO2
Test 1
Test 2
Test C
−
TRANSMITTER SOLUTIONS iGAZE RE UL10kΩ KIT
Open Beam
Wall / Fence
Filler Post if necessary
Closed Gate
Open Edge
Open Edge
Entrapment Area
Closed Gate
Wall / Fence
Close Edge
Entrapment Area
Close Beam
Used with permission of DoorKing® Inc. All graphics, language and layouts
are copyright protected by DoorKing® Inc. of Inglewood, CA.
DoorKing assumes no responsibility for the accuracy of the information
provided by Transmitter Solutions.
3OPEN Edge/Beam Reverse: Obstructed reversing
edge or photo beam will reverse the gate to the close position
during the opening-direction only.
• After the gate reverses to the close position, any opening input
will cycle the gate again. Note: If the gate is opening by a time
clock and a edge/beam gets obstructed, the gate will return to the
closed position and another input (automatic exit loop, reverse
loop, remote etc.) is needed to cycle the gate open again.
4CLOSE Edge/Beam Reverse: Obstructed reversing
edge or photo beam will reverse the gate to the open position
during the closing-direction only.
• After the gate reverses to the open position, the close-timer will
time out and close the gate (if it is turned on).
• If a second sequential obstruction is encountered prior to the
gate reaching the close limit, the gate will reverse to full open
position and enter a soft shutdown condition.
OPEN EDGE
Dip Switch 3: ON
UL 325
Terminal
UL 325 DIP-Switches
Common
Full Open
24 VDC
GND
GND
CE
OE
CB
OB
1 2 3 4 5 6
7 8 9 10
1234
ON
IGAZEREKIT-UL
TRANSMITTER SOLUTIONS iGAZE RE UL 10kΩ KIT
+
C1
12/24
NC1
NO1
C2
NC2
NO2
Test 1
Test 2
Test C
−
CLOSED EDGE
Dip Switch 3: ON
UL 325
Terminal
UL 325 DIP-Switches
Common
Full Open
24 VDC
GND
GND
CE
OE
CB
OB
1 2 3 4 5 6
7 8 9 10
1234
ON
IGAZEREKIT-UL
/