MicroNet SP5563HTM Quick Installation Guide

MicroNet
Brand
MicroNet
Model
SP5563HTM
Category
Security camera accessories
Type
Quick Installation Guide
Communicate via
Quick Installation Guide
Model No.: SP5563HTM
P/N 2300-0675
6
5
7
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
Full HD Box IP Camera
Step 2: Before Login to the Box IP Camera
A client program will be automatically installed on your PC when
connecting to the Box IP Camera. Before logging in to the Box IP
Camera, please ensure downloading the ActiveX control is allowed
by either changing the ActiveX controls and plug-ins or setting
Internet's security level to default. For further details, please refer to
the Box IP Camera's user manual.
www.micronet.com.tw
ActiveX Controls and Plug-ins Settings
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the browser. Then
Click <Internet Options>.
Step 3: Click the <Security> tab and select "Internet", and click
<Custom level> to change ActiveX settings.
Step 4: Set "ActiveX controls and plug-ins" items to <Prompt>
or <Enable>.
Step 1:
Step 1:
Step 1:
Internet Security Level
Step 1: Start the IE.
Step 2: Select <Tools> from the main menu of the browser. Then
Click <Internet Options>.
Step 3: Click the <Security> tab and select "Internet."
Step 4: Down the page, press "Default Level" and click "OK" to
confirm the setting. Close the browser window, and open a
new one later for accessing the Box IP Camera.
Step 1:
Step 1:
Step 1:
Step 3: Box IP Camera Login
The Box IP Camera's default IP address is: 192.168.1.2. Therefore,
to access the Box IP Camera for the first time, set the PC's IP
address as: 192.168.1.X; for example:
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Login ID & Password
Key in the Box IP Camera's IP address in the URL bar of the
Web browser window and press "Enter."
Enter the default user name (root) and password (pass) in the
prompt request dialogue. Note that user name and password are
case sensitive.
Install the ActiveX Control
After connecting to the Box IP Camera, the request for installing
the ActiveX control will appear just below the URL bar.
Right Click on the information bar, and press "Install ActiveX
Control..." to permit ActiveX control installation.
In the pop-up security
warning window, click
"Install" to start
downloading DC Viewer
software on the PC.
Press "Finish" after DC
Viewer installation
is complete.
Browser-based Viewer
The main page of the Box IP Camera user interface is shown as the
figure below. Please note that function buttons will vary depending
on the camera model.
This Quick Installarion Guide is for quick installing and connecting
the Micronet SP5563HTM Full HD Box IP Camera. For details,
please refer to the Box IP Camera's User Manual.
Version 1.0
4
3
1 2
Package Contents
Please check the package contains the following items listed below.
Introduction
Micronet SP5563HTM Full HD Box IP Camera is capable of serving
real-time streaming and makes image quality more smoothly. In
addition to MJPEG real time streaming, this camera develops H.264
codec to apply for high resolution digital broadcast.
In addition to MJPEG real time streaming, Full HD IP Camera
develops superior H.264 to apply for high resolution digital
broadcast. Attributing to the IP Camera's flexible platform, the
camera can be applied in various installation locations including
shops, stores, banks, parking lots, factories and building
surveillance.
Features
Progressive Scan CMOS Sensor
Full HD 1080p
H.264 and MJPEG Compression
Motion Detection
Privacy Masks
Day/Night (ICR)
Auto Iris Lens Support
Micro SD Support
BNC Analog Output
ONVIF Support
Camera Rear Panel
DC 12V/ PoE
Box IP Camera
Back focus
adjuster
Quick Guide
CD (bundled software
and documentation)
System Requirements
To perform the IP Camera via web browser, please ensure your PC
is in good network connection, and meet system requirements as
described below.
Items
Personal
Computer
Operating
System
Web
Browser
Network
Card
Viewer
System Requirement
®® ®TM
Intel Pentium M, 2.16 GHz or Intel Core 2 Duo, 2.0 GHz
2 GB RAM or above
Windows VISTA/ Windows XP/ Windows 7
Microsoft Internet Explorer 6.0 or above
Firefox, Chrome, Safari
10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation
ActiveX control plug-in for Microsoft IE
Definition
1 NETWORK (with PoE)
2 Network LEDs
3 AUTO IRIS connector
4
5
VIDEO (BNC connector)
7 I/O
8 Power LED
9 Reset button
LINE OUT &
LINE IN / MIC IN
Micro SD Card slot
6
10 DC 12V connector
Remarks
RJ45 connector
Network connection and activity indication
Auto iris lens connector
Two-way audio transmission
For video output
For video output
1 Output 5GND
2 Output 6D
3 Input 7D
4 Input
Power connection indication (green light)
Reset to factory default
DC 12V: Power
DC 12V: R eserved
DC 12V: GND
5 GND
6 D
7 D
Step 1: Box IP Camera Installation
Please follow the instructions below to complete Box IP Camera
installation.
Lens Mounting
If use C-Mount lens, after removing the camera's plastic cover,
users need to mount the supplied C/CS mount adapter to the
camera. Then attach the lens onto the C/CS mount adapter.
C/CS Mount Adapter Completion
Ethernet Cable Connection
Connect one end of the CAT5 Ethernet cable to the RJ45 connector
of the Box IP Camera, and the other end of the cable to the network
switch or PC.
NOTE: In some cases, you may need to use an Ethernet crossover
cable when connecting the Box IP Camera directly to the PC.
NOTE: Check the status of the link indicator and activity indicator
LEDs; if the LEDs are unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Power up the Camera
To power up the Box IP Camera, please plug the camera's DC 12V
cable into the power outlet. Alternatively, connect the Ethernet cable
to the camera's PoE port and plug the other end of the cable into a
PoE switch.
NOTE: If using PoE, make sure Power Sourcing Equipment
(PSE) is in use in the network.
1
3
4
5
6
7
8
9
10
2 2
  • Page 1 1
  • Page 2 2

MicroNet SP5563HTM Quick Installation Guide

MicroNet
Brand
MicroNet
Model
SP5563HTM
Category
Security camera accessories
Type
Quick Installation Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents