Foreword
Product Safety and RF Exposure Compliance
ATTENTION!
This RSM, when attached to the radio, is restricted to
occupational use only to satisfy FCC RF energy exposure
requirements. Before using this product, read the RF energy
awareness information and operating instructions in the Product
Safety and RF Exposure booklet enclosed with your radio
(Motorola Publication part number 6881095C98) to ensure
compliance with RF energy exposure limits.
For information regarding radio use in a hazardous atmosphere,
please refer to the Factory Mutual (FM) Approval Product Listing,
which is included with radio models that offer this capability.
Radio Compatibility
The RMN5038 RSM is only compatible and certified for use with the
following radio models:
Note: This RSM is not compatible with JT 1000 or MTX 8000/9000
portable radios. These radios do not support the emergency
features on the RSM.
Submersibility
The RMN5038 is submersible at the mic head, including the strain
relief mic head/cord interface. The RMN5038 RSM is submersible at
the radio connector also, when used with the following Ruggedized
radio models:
RSM Enhanced Features
The following diagram will help you locate the enhanced physical
features of your RSM:
Attaching the RSM
To attach the RSM to the radio:
Receiving and Transmitting
When the RSM is connected to the radio, you will hear audio only from
the speaker in the microphone.
To transmit using your RSM:
Changing the Volume
The and
²
buttons allow you to switch the volume from the radio’s
setting to a lower level and back again without having to touch the
radio. Press the
²
button to decrease the volume to a lower level;
press the
button to return the volume to the radio’s setting.
Using the Orange Emergency Button
The orange (top) button activates the Emergency mode of your radio.
Be sure to read the programming information on the next page.
Your radio’s User Guide contains a full description of the Emergency
mode.
To activate the Emergency mode from the RSM:
For XTS 3000 radios with host code 06.xx.xx and all XTS 1500,
XTS 2500, and XTS 5000 radios:
For all other radios:
Before using this product, read the operating
instructions for safe usage contained in the Product
Safety and RF Exposure booklet enclosed with your
radio.
XTS 5000 XTS 3500 XTS 3000 XTS 2500 XTS 1500
HT1000 MTS2000 MT2000 GT900 / HT1100
XTS 3000R XTS 3500R XTS 5000R
!
C a u t i o n
1 Align and attach the microphone’s connector to the radio’s
side connector.
2 Secure by tightening the screw on the upper end of the
connector.
1 Press and hold the Push-To-Talk (PTT) button on the RSM.
2 Speak into the RSM.
3 Release the PTT when finished.
Note: Connecting the RSM to the radio does not disable the radio’s
microphone and PTT.
Push-to-Talk
Button
Volume "+"
Button
Volume "-"
Button
Emergency
Button (orange)
1 Press and release the orange button on the RSM. The radio
will activate the Emergency signal after the programmed
Pre-Alert and Post-Alert delays elapse.
1 Press and hold the orange button on the RSM.
2 Wait for programmed Pre-Alert delay to elapse.
3 Listen for the Alert Tone (2 beeps).
4 Continue pressing the orange button through Post-Alert delay.
5 Release the orange button when the radio enters Emergency
mode.
Note: No alert tone will sound if the radio is programmed for silent
emergency.
The Emergency mode is indicated by a short, medium-pitched
tone. Display radios will alternate “emergency” with zone/channel
display. Radios programmed for silent emergency will not sound
alert or emergency tones, and the display will not change.
CAUTION!
RADIO PROGRAMMING REQUIRED - Read Carefully!
How to Program the Radio (Required)
Radios can be programmed using existing Radio Service Software
(RSS) or Customer Programming Software (CPS)
.
Attaching and Removing the Belt/Swivel Clip
To attach the belt/swivel clip:
To remove the belt/swivel clip:
Service, Support, and Warranty
The RMN5038 Emergency RSM is not repairable. It is covered under
the standard Motorola one-year limited warranty. Refer to your
Motorola dealer or point-of-purchase for detailed information on
warranty replacement.
A replacement swivel clip (4205823V01) may be ordered through your
Motorola dealer or by calling Motorola Radio Products Services
Division at 1-800-422-4210.
Motorola, Inc.
8000 West Sunrise Boulevard
Ft. Lauderdale, FL 33322
MOTOROLA, and the Stylized M logo are registered in the US Patent &
Trademark Office. All other product or service names are the property
of their respective owners.
© Motorola, Inc. 2003.
All rights reserved. Printed in U.S.A.
*6881097C39*
6881097C39-O
The following radio programming is REQUIRED for the
RSM’s Emergency button to operate properly.
Emergency activation from the RSM is delayed until
programmed Pre-Alert and Post-Alert delays elapse.
Factory defaults or previous programming could have set
the delay times to as long as 8-120 seconds (depending
on the radio model), so it is essential
that the radio be
checked and programmed appropriately.
Programming of the Pre-Alert and Post-Alert delays affects
only the RSM’s Emergency button and does not affect the
radio’s Emergency button operation.
Feature How to Program
Emergency Must be enabled.
Emergency Mandown
Must be enabled (automatically enabled in
XTS models).
Emergency Mandown
Pre-Alert Delay
Set to short time period. 0 to 1 second is
suggested.
Emergency Mandown
Post-Alert Delay
Set to short time period. 0 to 1 second is
suggested.
!
C a u t i o n
1 Attach and slide the belt/swivel clip down the grooved rails on
the back of the RSM.
2 Push firmly until it clicks into place.
1 Insert the flat blade of a small screwdriver (or like instrument)
between the release tab and the back surface of the
microphone.
2 While holding the screwdriver in place against the release tab,
push the belt/swivel clip toward the top of the microphone until it
moves up and off.
Emergency
Remote Speaker Microphone (RSM)
User Guide
Model RMN5038
/
