Sony α 55 User manual

SLT-A33/A55/A55V 4-187-045-13 (1)

Printed using VOC (Volatile Organic

Compound)-free vegetable oil based ink.

Additional information on this product and

answers to frequently asked questions can be

found at our Customer Support Website.

A-mount

Instruction Manual

Interchangeable Lens

Digital Camera

Preparing the camera

Before your operation

Shooting images

Using the shooting function

Using the viewing function

Changing your setup

Viewing images on a

computer

Printing images

Others

Index

2

Owner’s Record

The model and serial numbers are located

on the bottom.

Record the serial number in the space

provided below.

Refer to these numbers whenever you call

upon your Sony dealer regarding this

product.

Model No. SLT-A55/A55V/A33

Serial No. __________________________

To reduce fire or shock hazard, do

not expose the unit to rain or

moisture.

IMPORTANT SAFETY

INSTRUCTIONS

SAVE THESE

INSTRUCTIONS.

DANGER - TO

REDUCE THE RISK

OF FIRE OR

ELECTRIC SHOCK,

CAREFULLY

FOLLOW THESE

INSTRUCTIONS.

If the shape of the plug does not fit the

power outlet, use an attachment plug

adaptor of the proper configuration for the

power outlet.

Battery pack

If the battery pack is mishandled, the

battery pack can burst, cause a fire or even

chemical burns. Observe the following

cautions.

• Do not disassemble.

• Do not crush and do not expose the

battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow

metal objects to come into contact with

the battery terminals.

• Do not expose to high temperature above

60°C (140°F) such as in direct sunlight or

in a car parked in the sun.

• Do not incinerate or dispose of in fire.

• Do not handle damaged or leaking

lithium ion batteries.

• Be sure to charge the battery pack using a

genuine Sony battery charger or a device

that can charge the battery pack.

WARNING

Caution

3

• Keep the battery pack out of the reach of

small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent

type recommended by Sony.

• Dispose of used battery pack promptly

described the instructions.

Battery charger

Even if the CHARGE lamp is not lit, the

battery charger is not disconnected from the

AC power source (mains) as long as it is

connected to the wall outlet (wall socket).

If some trouble occurs while using the

battery charger, immediately shut off the

power by disconnecting the plug from the

wall outlet (wall socket).

When a power cord (mains lead) is

supplied, the power cord (mains lead) can

be used with this unit only, and should not

be used with any other unit.

RECYCLING LITHIUM-ION

BATTERIES

Lithium-Ion batteries are

recyclable.

You can help preserve

our environment by

returning your used

rechargeable batteries to

the collection and

recycling location nearest you.

For more information regarding recycling

of rechargeable batteries, call toll free

1-800-822-8837, or visit http://

www.rbrc.org/

Caution: Do not handle damaged or

leaking Lithium-Ion batteries.

Battery pack

This device complies with Part 15 of the

FCC Rules, Operation is subject to the

following two conditions:

(1) This device may not cause harmful

interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

This Class B digital apparatus complies

with Canadian ICES-003.

UL is an internationally recognized safety

organization.

The UL Mark on the product means it has

been UL Listed.

For Customers in the U.S.A.

and Canada

For Customers in the U.S.A.

4

If you have any questions about this

product, you may call:

Sony Customer Information Services

Center

1-800-222-SONY (7669)

The number below is for the FCC related

matters only.

Regulatory Information

CAUTION

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

Note:

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user

is encouraged to try to correct the

interference by one or more of the

following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

The supplied interface cable must be used

with the equipment in order to comply with

the limits for a digital device pursuant to

Subpart B of Part 15 of FCC Rules.

Declaration of Conformity

Trade Name: SONY

Model No.: SLT-A55V

Responsible Party: Sony Electronics

Inc.

Address:16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This

device may not cause harmful

interference, and (2) this device must

accept any interference received,

including interference that may cause

undesired operation.

Declaration of Conformity

Trade Name: SONY

Model No.: SLT-A33

Responsible Party: Sony Electronics

Inc.

Address:16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This

device may not cause harmful

interference, and (2) this device must

accept any interference received,

including interference that may cause

undesired operation.

5

Hereby, Sony Corporation, declares that

this SLT-A55V Interchangeable Lens

Digital Camera is in compliance with the

essential requirements and other relevant

provisions of the Directive 1999/5/EC. For

details, please access the following URL:

http://www.compliance.sony.de/

Notice for the customers in the

countries applying EU Directives

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan Minato-ku

Tokyo, 108-0075 Japan. The Authorized

Representative for EMC and product safety

is Sony Deutschland GmbH, Hedelfinger

Strasse 61, 70327 Stuttgart, Germany. For

any service or guarantee matters please

refer to the addresses given in separate

service or guarantee documents.

This product has been tested and found

compliant with the limits set out in the

EMC Directive for using connection cables

shorter than 3 meters (9.8 feet).

Attention

The electromagnetic fields at the specific

frequencies may influence the picture and

sound of this unit.

Notice

If static electricity or electromagnetism

causes data transfer to discontinue midway

(fail), restart the application or disconnect

and connect the communication cable

(USB, etc.) again.

Disposal of Old Electrical &

Electronic Equipment (Applicable in

the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its

packaging indicates that this product shall

not be treated as household waste. Instead it

shall be handed over to the applicable

collection point for the recycling of

electrical and electronic equipment. By

ensuring this product is disposed of

correctly, you will help prevent potential

negative consequences for the environment

and human health, which could otherwise

be caused by inappropriate waste handling

of this product. The recycling of materials

will help to conserve natural resources. For

more detailed information about recycling

of this product, please contact your local

Civic Office, your household waste

disposal service or the shop where you

purchased the product.

For Customers in Europe

6

Disposal of waste batteries

(applicable in the European Union

and other European countries with

separate collection systems)

This symbol on the battery or on the

packaging indicates that the battery

provided with this product shall not be

treated as household waste.

On certain batteries this symbol might be

used in combination with a chemical

symbol. The chemical symbols for mercury

(Hg) or lead (Pb) are added if the battery

contains more than 0.0005% mercury or

0.004% lead.

By ensuring these batteries are disposed of

correctly, you will help prevent potentially

negative consequences for the environment

and human health which could otherwise be

caused by inappropriate waste handling of

the battery. The recycling of the materials

will help to conserve natural resources.

In case of products that for safety,

performance or data integrity reasons

require a permanent connection with an

incorporated battery, this battery should be

replaced by qualified service staff only.

To ensure that the battery will be treated

properly, hand over the product at end-of-

life to the applicable collection point for the

recycling of electrical and electronic

equipment.

For all other batteries, please view the

section on how to remove the battery from

the product safely. Hand the battery over to

the applicable collection point for the

recycling of waste batteries.

For more detailed information about

recycling of this product or battery, please

contact your local Civic Office, your

household waste disposal service or the

shop where you purchased the product.

A moulded plug complying with BS 1363

is fitted to this equipment for your safety

and convenience.

Should the fuse in the plug supplied need to

be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or

BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has

a detachable fuse cover, be sure to attach

the fuse cover after you change the fuse.

Never use the plug without the fuse cover.

If you should lose the fuse cover, please

contact your nearest Sony service station.

Notice for customers in the

United Kingdom

7

Notes on using your camera

Shooting procedure

• This camera has two modes for shooting:

the LCD monitor mode using the LCD

monitor, and the viewfinder mode using

the viewfinder.

• The recorded image may be different

from the image you monitored before

recording.

Notes on the functions available with

the camera

• To check whether it is a 1080 60i-

compatible device or 1080 50i-

compatible device, check for the

following marks on the bottom of the

camera.

1080 60i-compatible device:60i

1080 50i-compatible device:50i

• You may feel uncomfortable symptoms

such as eyestrain, nausea, or a tired

feeling while watching 3D-images

recorded with the camera on 3D-

compatible monitors. When you watch

3D-images, we recommend that you take

a break at regular time intervals. Since

the need for or frequency of break times

varies between individuals, please set

your own standards. If you feel sick, stop

watching 3D-images, and consult a

doctor as needed. Also, refer to the

operating instructions of the connected

device or the software used with the

camera. A child’s vision is always

vulnerable (especially for children under

six years of age). Before allowing them

to watch 3D-images, please consult with

an expert, such as a pediatric or

ophthalmic doctor. Be sure to make sure

your children follow the precautions

above.

No compensation for contents of the

recording

The contents of the recording cannot be

compensated for if recording or playback is

not possible due to a malfunction of your

camera or a memory card, etc.

Back up recommendation

To avoid the potential risk of data loss,

always copy (back up) data to other

medium.

Notes on the LCD monitor, electronic

viewfinder, lens, and image sensor

• The LCD monitor and electronic

viewfinder are manufactured using

extremely high-precision technology so

over 99.99% of the pixels are operational

for effective use. However, there may be

some tiny black points and/or bright

points (white, red, blue or green in color)

that constantly appear on the LCD

monitor and electronic viewfinder. These

points are normal in the manufacturing

process and do not affect the images in

any way.

• When you change your focus on the

viewfinder, red, green, or blue flickers

may appear on the screen. This is not a

malfunction. These flickers are not

recorded on the image.

• Do not hold the camera by taking hold of

the LCD monitor.

• Do not expose the camera to sunlight or

shoot sunward for a long time. The

internal mechanism may be damaged. If

sunlight is focused on a nearby object, it

may cause a fire.

• There is a magnet on the back and around

the rotating shaft of the hinge part of the

LCD monitor. Do not bring anything that

is easily affected by a magnet, such as

floppy disk, credit cards near the LCD

monitor.

• Images may trail across on the screen in a

cold location. This is not a malfunction.

When turning on the camera in a cold

location, the screen may become

temporarily dark. When the camera

warms up, the screen will function

normally.

8

Notes on long-time recording

• When you continue to shoot for a long

time, the temperature of the camera rises.

If the temperature reaches above a certain

level, the mark is indicated on the

screen and the camera is turned off

automatically. If the power is turned off,

leave the camera for 10 minutes or longer

to allow the temperature inside the

camera to decrease to a safe level.

• Under high ambient temperatures, the

temperature of the camera rises quickly.

• When the temperature of the camera

rises, the image quality may deteriorate.

It is recommended that you wait until the

temperature of the camera drops before

continuing to shoot.

• The surface of the camera may get hot.

This is not a malfunction.

Notes when playing movies on other

devices

• This camera uses MPEG-4 AVC/H.264

High Profile for AVCHD format

recording. Movies recorded in AVCHD

format with this camera cannot be played

with the following devices.

– Other devices compatible with

AVCHD format that does not support

High Profile

– Devices incompatible with the

AVCHD format

This camera also uses MPEG-4 AVC/

H.264 Main Profile for MP4 format

recording. For this reason, movies

recorded in MP4 format with this camera

cannot be played on devices other than

those that support MPEG-4 AVC/H.264.

• Discs recorded with HD image quality

(high definition) can be played back only

on AVCHD format-compatible devices.

DVD-based players or recorders cannot

play back HD image quality discs, as

they are incompatible with the AVCHD

format. Also, DVD-based players or

recorders may fail to eject HD image

quality discs.

On GPS-compatible devices (SLT-

A55V only)

• To determine whether your camera

supports GPS function, check the model

name of your camera.

GPS-compatible: SLT-A55V

GPS-incompatible: SLT-A55/A33

• Use GPS in accordance with regulations

of countries and regions where you use it.

• If you do not record the location

information, set [GPS On/Off] to [Off]

(page 138).

• In an airplane, make sure to turn off the

camera following cabin announcements.

Warning on copyright

Television programs, films, videotapes, and

other materials may be copyrighted.

Unauthorized recording of such materials

may be contrary to the provisions of the

copyright laws.

The pictures used in this manual

The photographs used as examples of

pictures in this manual are reproduced

images, and are not actual images shot

using this camera.

On the data specifications described

in this Instruction Manual

The data on performance and specifications

is defined under the following conditions,

except as described in this Instruction

Manual: at an ordinary ambient

temperature of 25ºC (77°F), and using a

battery pack that is charged for about an

hour after the CHARGE lamp goes out.

9

Table of Contents

Notes on using your camera .............................................. 7

Preparing the

camera

Checking the accessories supplied .................................. 13

Identifying parts .............................................................. 14

Charging the battery pack ................................................ 18

Inserting the battery pack/memory card (sold separately)

..................................................................................... 20

Attaching a lens ............................................................... 26

Preparing the camera ....................................................... 28

Using the accessories supplied ........................................ 30

Checking the number of recordable images .................... 32

Cleaning ........................................................................... 35

Before your

operation

Screen indicators ............................................................. 39

Switching the screen mode between the LCD monitor

and the electronic viewfinder ............................ 39

Switching the recording information display (DISP)

............................................................................ 40

Recording information display (Graphic Display/

Recording information (For Live View)) .......... 42

Recording information display (For viewfinder) ....... 44

Selecting a function/setting ............................................. 46

Selecting a function with the Fn (Function) button ... 47

The functions selected by the Fn (Function) button ... 48

The functions selected by the MENU button ............. 49

Shooting images

Adjusting the angle of the LCD monitor ......................... 55

Shooting an image without camera shake ....................... 56

Correct posture ........................................................... 56

Using the SteadyShot function ................................... 57

Using a tripod ............................................................. 58

Shooting with the automatic setting ................................ 59

Shooting with appropriate settings

automatically ..................................................... 59

Shooting with the settings that the camera adjusts

automatically ..................................................... 61

10

Shooting with a suitable setting for the subject ............... 63

Shooting with preset settings according to the scene

(Scene Selection) ............................................... 63

Shooting panoramic images (Sweep Shooting) . 66

Shooting continuously at high speed (Continuous

Advance Priority AE) ........................................ 69

Shooting an image the way you want it (Exposure mode)

..................................................................................... 70

Shooting with program auto .................................. 71

Shooting by controlling the blur of the background

(Aperture priority) ............................................. 72

Shooting a moving subject with various expressions

(Shutter speed priority) ..................................... 75

Shooting with the exposure adjusted manually

(Manual exposure) ............................................ 77

Shooting trails with long exposure (BULB) .......... 79

Recording movies ............................................................ 81

Available recording time for a movie ........................ 83

Notes on continuous movie recording ........................ 84

Using the

shooting function

Selecting the focus method .............................................. 85

Using autofocus .......................................................... 85

Shooting with your desired composition (Focus-lock)

............................................................................ 87

Selecting the focus method to suit the movement of the

subject (Autofocus Mode) ................................. 88

Selecting the focus area (AF area) ............................. 89

Adjusting the focus manually (Manual focus) ........... 90

Checking the focus by enlarging the image ............... 91

Detecting faces ................................................................ 93

Using the Face Detection function ............................. 93

Capturing smiling faces (Smile Shutter) .................... 94

Using the flash ................................................................. 96

Performing wireless flash shooting ............................ 99

Adjusting the brightness of the image (Exposure, Flash

compensation, Metering) .......................................... 100

Shooting with fixed brightness (AE Lock) .............. 100

11

Using brightness compensation for the entire image

(Exposure compensation) ................................ 101

Adjusting the amount of flash light (Flash

Compensation) ................................................ 103

Selecting the flash control mode to set the amount of

flash light (Flash control) ................................ 104

Selecting the method for measuring the brightness of a

subject (Metering Mode) ................................. 105

Setting ISO .................................................................... 106

Compensating for the brightness and contrast automatically

(D-Range) ................................................................. 107

Correcting the brightness of the image (D-Range

Optimizer) ....................................................... 107

Compensating automatically with rich gradation (Auto

High Dynamic Range) .................................... 108

Image processing ........................................................... 110

Selecting your desired image processing (Creative Style)

.......................................................................... 110

Changing the range of color reproduction (Color Space)

.......................................................................... 111

Adjusting the color tones (White balance) .................... 112

Adjusting the white balance to suit a specific light source

(Auto/Preset white balance) ............................ 112

Setting the color temperature and a filter effect (Color

Temperature/Color Filter) ............................... 113

Registering the color tones (Custom white balance) 114

Selecting the drive mode .................................. 116

Shooting single shot ................................................. 116

Shooting continuously .............................................. 116

Using the self-timer .................................................. 117

Shooting images with the exposure shifted (Exposure

bracket) ............................................................ 118

Shooting with white balance shifted (WB bracket)

.......................................................................... 119

Shooting with the Wireless Remote Commander .... 120

12

Using the viewing

function

Playing back images ...................................................... 121

Checking the information of recorded images .............. 127

Protecting images (Protect) ........................................... 131

Deleting images (Delete) ............................................... 132

Viewing images on a TV screen .................................... 134

Changing your

setup

GPS setting (SLT-A55V only) ...................................... 138

Setting image size and image quality ............................ 141

Setting the method for recording on a memory card ..... 145

Changing the noise reduction setting ............................ 149

Changing the function of the buttons ............................ 150

Changing other settings ................................................. 151

Setting the LCD monitor/electronic viewfinder ............ 153

Confirming the version of the camera ........................... 155

Resetting to the default .................................................. 156

Viewing images

on a computer

Using with your computer ............................................. 159

Using the software ......................................................... 161

Connecting the camera to the computer ........................ 165

Creating a movie disc .................................................... 168

Printing images

Specifying DPOF ........................................................... 172

Others

Specifications ................................................................ 174

Troubleshooting ............................................................. 179

Warning messages ......................................................... 189

Precautions .................................................................... 192

AVCHD format ............................................................. 195

GPS (SLT-A55V only) .................................................. 196

3D-shootings .................................................................. 198

Index .............................................................................. 199

Preparing the camera

13

Preparing the camera

Checking the accessories supplied

The number in parentheses indicates the number of pieces.

• BC-VW1 Battery charger (1)

• Power cord (mains lead) (1) (not

supplied in the U.S.A. and

Canada)

• Rechargeable battery pack NP-

FW50 (1)

• USB cable (1)

• Shoulder strap (1)

• Body cap (1) (Attached on the

camera)

• Eyecup (1) (Attached on the

camera)

• CD-ROM (Application Software

for α camera) (1)

• Instruction Manual (This manual)

(1)

Note on using the lenses and

accessories

It is recommended that you use Sony

lenses/accessories* designed to suit the

characteristics of this camera. Using the

products of other manufacturers may

cause the camera not to operate to its

capability, or result in accidents and

malfunctions of the camera.

* Konica Minolta products are included.

14

Identifying parts

See the pages in parentheses for details of operation.

A Shutter button (59)

B Power switch (28)

C Control dial (73)

D Remote sensor

E Self-timer lamp (117)

F Lens contacts*

G Mirror*

H Preview button (74)

I Mount

J Built-in flash* (96)

K Microphone**

L Mode dial (59 – 80)

M (Flash pop-up) button (96)

N Lens release button (27)

O Focus mode switch (85, 90)

* Do not directly touch these

parts.

** Do not cover this part

during movie recording.

Front side

15

Preparing the camera

A Microphone**

B Auto-lock Accessory shoe (99)

C MENU button (49)

D Viewfinder* (39)

E Eyepiece sensors (39)

F Diopter-adjustment dial (29)

G LCD monitor (42, 121, 127)

H Light sensor (153)

I (Playback) button (121)

J Access lamp (22)

K For shooting: Focus Magnifier

button (91, 150)

For viewing: (Delete) button

(132)

L MOVIE button (81)

M FINDER/LCD button (39, 154)

N Speaker

O Image sensor position

mark (87)

P D-RANGE (Dynamic range)

button (107)

Q For shooting: AEL (AE lock)

button (78, 100)

For viewing: (Zoom in)

button (124)

R For shooting: (Exposure)

button (101)

For viewing: (Zoom out)

button (124)/ (Image index)

button (125)

S For shooting: Fn (Function)

button (47, 48)

For viewing: (Image

rotation) button (123)

Rear side

16

T Control button

When the menu is turned on: v/

V/b/B button (46)

When the menu is turned off:

DISP (Display) (40, 121)/WB

(White balance) (112)/

(Drive) (116)/ISO (106)

U Control button (Enter) (46)/AF

button (89)

* Do not directly touch these

parts.

** Do not cover this part

during movie recording.

17

Preparing the camera

A REMOTE terminal

• When connecting the RM-

S1AM/RM-L1AM Remote

Commander (sold separately) to

the camera, insert the plug of

the Remote Commander into

the REMOTE terminal,

aligning the guide of the plug

with the guide of the REMOTE

terminal. Make sure that the

cord of the Remote Commander

faces forward.

B Hooks for shoulder strap (30)

C HDMI terminal (134)

D (USB) terminal (165)

E Microphone jack

• When an external microphone

is connected, the internal

microphone is turned off

automatically. When the

external microphone is a plug-

in-power type, the power of the

microphone is supplied by the

camera.

F Tripod receptacle

• Use a tripod with a screw length

of less than 5.5 mm (7/32 inch).

You will be unable to firmly

secure the camera to tripods

having screws longer than 5.5

mm (7/32 inch), and may

damage the camera.

G Memory card insertion slot (20)

H Battery/memory card cover

(20)

I Connection plate cover

• For using the AC-PW20 AC

Adaptor (sold separately)

Be careful not to catch the cord

of the AC Adaptor in the cover

when you close the cover.

Sides/Bottom

18

Charging the battery pack

When using the camera for the first time, be sure to charge the NP-FW50

“InfoLITHIUM” battery pack (supplied).

The “InfoLITHIUM” battery pack can be charged even when it has not

been fully depleted.

It can also be used when it has not been fully charged.

1 Insert the battery pack onto the

battery charger.

Push the battery pack until it clicks.

2 Connect the battery charger to the

wall outlet (wall socket).

Light on: Charging

Light off: Charge completed

• The CHARGE lamp turns off when

charging is finished.

• Time required to charge a fully

depleted battery pack at a temperature

of 25°C (77°F) is about 250 minutes.

For the U.S.A and Canada

CHARGE lamp

For countries/regions other than the

U.S.A. and Canada

Power cord (mains lead)

Plug

CHARGE lamp

19

Preparing the camera

Notes

• The charging time differs depending on the remaining capacity of the battery back or

charging conditions.

• We recommend charging the battery pack in an ambient temperature of between 10

to 30°C (50 to 86°F). You may not be able to efficiently charge the battery pack

outside of this temperature range.

• Connect the battery charger to the nearest wall outlet (wall socket).

• Do not try to charge the battery pack again right after it has been charged, or when it

has not been used after being charged. Doing so will affect the performance of the

battery pack.

• Do not charge any battery pack other than the “InfoLITHIUM” W series battery

pack in the battery charger (supplied) with your camera. Batteries other than the

specified kind may leak, overheat, or explode if you attempt to charge them, posing a

risk of injury from electrocution and burns.

• When the CHARGE lamp flashes, this may indicate a battery error or that a battery

pack other than the specified type has been installed. Check that the battery pack is

the specified type. If the battery pack is the specified type, remove the battery pack,

replace it with new one or another one and check if the battery charger operates

correctly. If the battery charger operates correctly, a battery error may have

occurred.

• If the battery charger is dirty, charging may not be performed successfully. Clean the

battery charger with dry cloth, etc.

To use your camera abroad — Power sources

You can use your camera and the battery charger and the AC-PW20 AC

Adaptor (sold separately) in any country or region where the power supply

is within 100 V to 240 V AC, 50/60 Hz.

Note

• Do not use an electronic transformer (travel converter), as this may cause a

malfunction.

20

Inserting the battery pack/memory card

(sold separately)

1 While sliding the cover open

lever, open the cover.

2 Firmly insert the battery pack all

the way while pressing the lock

lever with the tip of the battery.

Lock lever

3 Insert a memory card.

• With the notched corner facing as

illustrated, insert the memory card until

it clicks into place.

Ensure the notched corner faces

correctly.

4 Close the cover.

Page is loading ...

Sony α 55 User manual

Related papers

Other documents