Flytech POS375D User manual

USER MANUAL

Point-of-Sale

Hardware

System

VERSION V1.4 December 2010

ii

Manual Version 1.4

Part Number: 3LMPP3750114

The information contained in this document is subject to change without notice.

We make no warranty of any kind with regard to this material, including, but not

limited to, the implied warranties of merchantability and fitness for a particular

purpose. We shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of

this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of the

manufacturer.

TRADEMARK

Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.

Microsoft® and Windows® are registered trademarks of Microsoft Corporation.

Other trademarks mentioned herein are the property of their respective owners.

Safety

IMPORTANT SAFETY INSTRUCTIONS

To disconnect the machine from the electrical power supply, turn off the power 1.

switch and remove the power cord plug from the wall socket. The wall socket

must be easily accessible and in close proximity to the machine.

Read these instructions carefully. Save these instructions for future reference.2.

Follow all warnings and instructions marked on the product.3.

Do not use this product near water.4.

Do not place this product on an unstable cart, stand, or table. The product may 5.

fall, causing serious damage to the product.

Slots and openings in the cabinet and the back or bottom are provided for 6.

ventilation to ensure reliable operation of the product and to protect it from

overheating. These openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed, sofa, rug, or other

similar surface. This product should never be placed near or over a radiator or

heat register or in a built-in installation unless proper ventilation is provided.

This product should be operated from the type of power indicated on the 7.

marking label. If you are not sure of the type of power available, consult your

dealer or local power company.

Do not allow anything to rest on the power cord. Do not locate this product 8.

where persons will walk on the cord.

Never push objects of any kind into this product through cabinet slots as they 9.

may touch dangerous voltage points or short out parts that could result in a ﬁre

or electric shock. Never spill liquid of any kind on the product.

iii

CE MARK

This device complies with the requirements of the EEC directive 2004/108/EC

with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage

Directive”.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that

may cause undesired operation.

CAUTION ON LITHIUM BATTERIES

There is a danger of explosion if the battery is replaced incorrectly. Replace only

with the same or equivalent type recommended by the manufacturer. Discard

used batteries according to the manufacturer’s instructions.

Battery Caution

Risk of explosion if battery is replaced by an incorrectly type.

Dispose of used battery according to the local disposal instructions.

Safety Caution

Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S)

related legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure”

compliant

4.7.3.2 Materials for ﬁ re enclosures

For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material

of a FIRE ENCLOSURE, in the thinnest signiﬁ cant wall thickness used, shall be

of V-1 CLASS MATERIAL or shall pass the test of Clause A.2.

For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all

STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest

signiﬁ cant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass

the test of Clause A.1

iv

LEGISLATION AND WEEE SYMBOL

2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,

collection, recycling and disposal of electric and electronic devices and their

components.

The crossed dust bin symbol on the device means that it should not be disposed

of with other household wastes at the end of its working life. Instead, the device

should be taken to the waste collection centers for activation of the treatment,

collection, recycling and disposal procedure.

To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this

product, or their local government office, for details of where and how they can

take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of

the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

v

Revision History

Changes to the original user manual are listed below:

Revision Description Date

1.0 Initial release• 2009 March

1.1 B68 motherboard added• 2010 March

1.2

C48 motherboard added•

Optional Accessories updated•

Speciﬁcation updated•

2010 July

1.3 B68 & B78 Jumper Setting update• 2010 August

1.4 C48 update to V2.1• 2010 December

vi

Table of Contents

1. Packing List .............................. 1

1-1. Standard Accessories ..............................................1

1-2. Optional Accessories ...............................................2

2. System View ............................. 3

2-1. Front & Side View ....................................................3

2-2. Rear View with stand ...............................................4

2-3. I/O Ports View ..........................................................5

2-4. System Dimension ...................................................6

3. System Assembly .................... 7

3-1. HDD replacement for fan system ............................7

3-2. RAM Replacement ..................................................8

3-3. Power Adapter Replacement ...................................9

4. Peripheral Installation ............ 10

4-1. MSR Installation .....................................................10

4-2. VFD Installation ......................................................11

4-3. Second Display Installation ....................................12

4-4. WLAN Installation ...................................................13

4-5. Cash Drawer Installation .......................................15

4-5-1. For B78 motherboard .............................................. 15

4-5-2. For B68/B98/C48 motherboard ............................... 17

vii

5. Speciﬁcation ........................... 19

6. Jumper Setting ........................ 21

6-1. For B68 Motherboard .............................................21

6-1-1. Motherboard Layout ................................................ 21

6-1-2. Connectors & Functions .......................................... 22

6-1-3. Jumper Setting ........................................................ 23

6-2. For B78 Motherboard .............................................26

6-2-1. Motherboard Layout ................................................ 26

6-2-2. Connectors & Functions .......................................... 27

6-2-3. Jumper Setting ........................................................ 28

6-3. For B98 Motherboard .............................................31

6-3-1. Motherboard Layout ................................................ 31

6-3-2. Connectors & Functions .......................................... 32

6-3-3. Jumper Setting ........................................................ 33

6-4. For C48 Motherboard .............................................36

6-4-1. Motherboard Layout ................................................ 36

6-4-2. Connectors & Functions .......................................... 37

6-4-3. Jumper Setting ........................................................ 38

Appendix: Drivers Installation .... 43

viii

The page is intentionally left blank.

1

Packing List1.

Standard Accessories

1-1.

System (with stand)a.

Driver bankb.

User guidec.

Power adapterd.

Power corde.

RJ45-DB9 cable (x2)f.

Note: Power cord will be supplied differently according to

various region or country.

a

b

c

d

e

f

2

Optional Accessories

1-2.

3-in-1 MSR modulea.

Mini PCI or mini PCI-E WLAN Card (with internal antenna cable)b.

Second display module (with VGA cable)c.

VFD module (with RJ-45 cable)d.

3

System View2.

Front & Side View

2-1.

Item No. Description

1 Touch screen

2 MSR module (optional)

3 HDD installation cover

4 Power LED

5 Power Button

6 Hinge for TFT-LCD

7 Thumb screw for HDD cover

8 VFD

9 Ventilation

10 Rear cover for motherboard metal cover

11 Rugged footprint

1

2

3

4

5

7

8

9

10

11

6

4

Rear View with stand

2-2.

Item No. Description

12 VESA mount installation plate

13 System Fan

14 Power adapter cable outlet

15 Thumb screws of rear cover

5

I/O Ports View

2-3.

Item No. Description

a 2nd VGA

b DC-In

c LAN

d Cash Drawer (12V/24V)

e MIC-in

f Line-out

g COM 1, 2, 3, 4 (from left to right)

h USB x 4

i Parallel

j Power Switch

k USB x 2

l LCD Connector

m Power LED

4

6

5

3

CD

1

19

V

IN

COM4COM3COM2COM1

bcdef g h

a

ij

k

lm

6

System Dimension

2-4.

366mm

414.7mm

340.5mm

289.6mm

266.3mm

78°

301.6mm

61.3mm

225mm

7

System Assembly3.

Loose the thumb screw on the 1.

HDD cover.

Open the HDD cover.2.

Install the 3.5” HDD and fasten 3.

the screw (x1) with the bracket to

fix the 3.5” HDD.

Connect the SATA cable and 4.

cover the HDD cover.

HDD replacement for fan system

3-1.

To remove and replace the HDD, please follow below steps. The procedures may

be slightly different depending on 3.5” or 2.5 HDD you will install.

For 3.5” HDD

For 2.5” HDD

If your system is installed with 2.5” 5.

HDD, please fasten the screws

(x2) and connect the SATA cable

and cover the HDD cover.

8

Removing a RAM module

Use both fingers to pull the ejector 1.

clips out of the sides of the module.

Slide out to take out the memory 2.

module from the memory slot.

Installing a RAM module

Slide the memory module into the 3.

memory slot and press down until

it fix with the ejector clips.

Please open the rear cover (see Chapter 4-4 step 1&2) ﬁrst then remove and

replace the RAM module. You can refer to the motherboard layout to ﬁnd the

memory compartment. (See chapter 6-1-1, 6-2-1, 6-3-1, 6-4-1 for different

motherboard)

RAM Replacement

3-2.

9

Power Adapter Replacement

3-3.

Unfasten the thumb screws (x2) to 1.

open the rear cover which covered

the motherboard and the sheet

metal bracket.

Connect the power cable to the I/O 2.

panel.

Cover the rear cover again and 3.

manage the power cable and the

adapter from the cable outlet of the

rear cover.

10

Peripheral Installation4.

MSR Installation

4-1.

Open the MSR cover on the TFT LCD module and install the MSR module 1.

into the right position. The installing connectors vary according to different

MSR module.

The system provide 5 kinds of MSR for selections: MSR, 2-in-1 MSR+smart IC

card reader, 2-in-1 MSR+ﬁngerprint reader, 2-in-1 MSR+iButton reader and the

3-in-1 MSR+smart IC card reader+iButton reader modules.

11

Open the rear cover by loosen the 1.

thumb screws (x2) on the both sides.

Uncover the VFD cover by loosen 2.

the screw (x1).

VFD Installation

4-2.

Install the VFD module by aligning 3.

the metal bracket attached to the

rear of the VFD into the right position

of the system and fasten the screws

(x2) to fix the VFD module with the

POS system.

Cover the VFD cover provided and 4.

fasten the screw (x1).

Connect the RJ45-RJ45 cable to 5.

VFD module and the I/O panel of the

system.

Cover the rear cover of the system 6.

and fasten the thumb screws (x2).

12

Second Display Installation

4-3.

Open the rear cover by loosen 1.

the thumb screws (x2) on the both

sides.

Uncover the VFD cover by loosen 2.

the screw (x1).

Aligning the metal bracket attached 3.

to the rear of the 2nd display

module into the right position of the

system and fasten the screws (x2)

to fix the 2nd display module with

the POS system.

Cover the 2nd display cover 4.

provided and fasten the screw (x1).

Connect the RJ45-VGA cable to the 5.

2nd display and the I/O panel.

Cover the rear cover of the system 6.

again and fasten the thumb screws

(x2).

Page is loading ...

Flytech POS375D User manual

This manual is also suitable for

Flytech POS375D User manual

Related papers

Other documents