PX750-ES-1A
ES
USER’S GUIDE
GUÍA DEL USUARIO
Please keep all information for future reference.
Guarde toda información para tener como referencia futura.
Safety Precautions
Before trying to use the piano, be sure to read
the separate “Safety Precautions”.
Precauciones de seguridad
Antes de intentar usar el piano, asegúrese de
leer las “Precauciones de seguridad” separadas.
EnglishEspañol
PX
-
75 0
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important!
Please note the following important information before using this product.
• Before using the AD-A12150LW Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check the power
cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged.
• The product is not intended for children under 3 years.
• Use only CASIO AD-A12150LW adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit
from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the
apparatus.
The P (POWER) indicator being unlit does not mean the apparatus is completely disconnected from the MAINS.
When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord. For that purpose, locate
the apparatus in a way that secures easy access to the power cord.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Declaration of Conformity
Model Number: PX-750
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Manufacturer:
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
This mark applies in EU countries only.
Declaration of Conformity According to EU Directive
E-1
English
Contents
General Guide ................................... E-2
FUNCTION Button...................................................... E-3
Saving Settings and Using Operation Lock ................ E-3
Power Outlet...................................... E-4
Using an AC Adaptor .................................................. E-4
Turning Power On or Off............................................. E-4
Connections...................................... E-6
Connecting Headphones ............................................ E-6
Connecting Audio Equipment or an Amplifier ............. E-6
Bundled and Optional Accessories............................. E-7
Playing with Different Tones ........... E-8
Selecting and Playing a Tone ..................................... E-8
Layering Two Tones ................................................. E-10
Using Effects............................................................. E-11
Using the Digital Piano’s Pedals............................... E-11
Using the Metronome ............................................... E-12
Playing a Piano Duet ................................................ E-13
Playing Back Built-in Songs .......... E-14
Playing Back All of the Built-in Songs....................... E-14
Playing Back a Specific Music Library Song............. E-15
Practicing with a Music Library Song........................ E-15
Recording and Play Back............... E-16
Tracks ....................................................................... E-16
To record to a specific track of a song...................... E-17
To record to one track of a song while
listening to the playback of the other track ............... E-18
Playing Back from Digital Piano Memory.................. E-18
Deleting Recorded Data ........................................... E-19
Configuring Settings with the
Keyboard ......................................... E-20
To configure settings with the keyboard....................E-20
Keyboard Keys Used for Configuring Settings.......... E-21
Parameter List...........................................................E-22
Tone selection ....................................................... E-22
Reverb ................................................................... E-22
Chorus ................................................................... E-22
Brilliance ................................................................ E-22
Layer balance ........................................................ E-22
Tempo (TEMPO) ................................................... E-22
Song select (SONG SELECT) ............................... E-22
Song volume.......................................................... E-22
Metronome beat (METRONOME BEAT) ............... E-22
Metronome volume ................................................E-22
Keyboard key (Transpose) .................................... E-23
Keyboard tuning (Tuning) ...................................... E-23
Octave shift............................................................ E-23
Temperament ........................................................ E-23
Temperament select..............................................E-23
Temperament Base note .......................................E-23
Touch response (TOUCH RESPONSE)................ E-23
USB device mode .................................................. E-24
Send channel......................................................... E-24
Local control .......................................................... E-24
Operation tone....................................................... E-24
Back up.................................................................. E-24
Operation lock........................................................ E-24
Connecting to a Computer............. E-25
Minimum Computer System Requirements .............. E-25
Connecting the Digital Piano to Your Computer ....... E-25
Using MIDI ................................................................ E-26
Transferring Song Data with a Computer.................. E-26
Reference......................................... E-33
Troubleshooting ........................................................ E-33
Product Specifications............................................... E-34
Operating Precautions .............................................. E-35
Appendix............................................ A-1
Tone List ..................................................................... A-1
Song List ..................................................................... A-1
MIDI Implementation Chart
Company and product names used in this manual may
be registered trademarks of others.
Assembling the Stand ............................................................................................... E-29
Unpacking................................................................. E-29
Assembling the Stand............................................... E-29
To connect the cable................................................. E-32
To install the music stand..........................................E-32
E-2
General Guide
21 3 4 5 6 8 97
bk bl bm
bo
bn
Bottom
Front
Rear
General Guide
E-3
English
NOTE
• The names shown here are always indicated in bold when they appear within the text of this manual.
The FUNCTION button is used when configuring a variety of different digital piano settings. The following are
FUNCTION button basics.
z To change a setting, hold down the FUNCTION button as you press the
keyboard key that is assigned the setting you want to select.
An operation confirmation tone will sound whenever you press a
keyboard key to configure a setting.
Example: “To select a tone” on page E-8
NOTE
• For details about operations and settings, see “Configuring Settings with
the Keyboard” on page E-20.
z The following table shows how pressing the FUNCTION button changes the operation of certain buttons.
Your digital piano lets you save its current settings and lock its buttons to protect against operation errors. For
details, see “Parameter List” on pages E-22 - E-24.
FUNCTION Button
This button: Does this while FUNCTION button is depressed:
SONG a Starts and stops demo tune play.
RECORDER Selects the left-hand part and the right-hand part.
METRONOME Toggles Duet on and off.
Saving Settings and Using Operation Lock
1 P (POWER) button
2 VOLUME controller
3 FUNCTION button
4 SONG a, DEMO button
5 RECORDER (L/R) button
6 METRONOME, DUET button
7 GRAND PIANO (CONCERT) button
8 GRAND PIANO (MODERN) button
9 ELEC PIANO button
bk Pedal connector
bl USB port
bm DC 12V terminal
bn PHONES jacks
bo Power lamp
E-4
Power Outlet
Your digital piano runs on standard household power.
Be sure to turn off power whenever you are not using
the digital piano.
Use only the AC adaptor (JEITA Standard, with unified
polarity plug) that comes with this digital piano. Use of
a different type of AC adaptor can cause malfunction
of the digital piano.
Specified AC Adaptor: AD-A12150LW
• Use the supplied power cord to connect the AC
adaptor as shown in the illustration below.
Note the following important precautions to avoid
damage to the power cord.
During Use
• Never pull on the cord with excessive force.
• Never repeatedly pull on the cord.
• Never twist the cord at the base of the plug or
connector.
During Movement
• Before moving the digital piano, be sure to unplug
the AC adaptor from the power outlet.
During Storage
• Loop and bundle the power cord, but never wind it
around the AC adaptor.
IMPORTANT!
• Never connect the AC adaptor (JEITA Standard,
with unified polarity plug) that comes with this digital
piano to any other device besides this piano. Doing
so creates the risk of malfunction.
• Make sure the digital piano is turned off before
plugging in or unplugging the AC adaptor.
• The AC adaptor will become warm to the touch after
very long use. This is normal and does not indicate
malfunction.
1.
Press the P (POWER) button to turn on
digital piano power.
• This causes the P (POWER) button to light.
• When you turn on the digital piano, it performs a
power up operation in order to initialize its system.
During system initialization the tone button lamps
cycle on and off in the sequence for about five
seconds to let you know that system initialization is
in progress.
2.
To turn off the digital piano, hold down the P
(POWER) button until its light goes out.
NOTE
• Pressing the P (POWER) button to turn off power
actually puts the digital piano into a standby state.
Minute amounts of current continue to flow within
the digital piano in the standby state. If you do not
plan to use the digital piano for a long time or if
there is a lightning storm in your area, be sure to
unplug the AC adaptor from the power outlet.
Using an AC Adaptor
Household power outlet
Power cord
DC 12V terminal
AC adaptor
• Configuration and type depends on
your geographic location.
Turning Power On or Off
English
Power Outlet
E-5
Auto Power Off
This digital piano is designed to turn off automatically
to avoid wasting power after no operation is
performed for a preset amount of time. The Auto
Power Off trigger time is about four hours.
• You also can use the procedure below to temporarily
suspend Auto Power Off.
■ To disable Auto Power Off
1.
While the digital piano is turned on, press the
P (POWER) button to turn it off.
2.
While holding down the FUNCTION button,
press the P (POWER) button to turn on the
digital piano.
• Auto Power Off will be disabled at this time.
NOTE
• Turning off the digital piano after performing the
above steps will re-enable Auto Power Off.
E-6
Connections
IMPORTANT!
• Whenever connecting something to the digital piano,
first use the VOLUME controller to set the volume to
a low level. After connecting, you can adjust the
volume to the level you want.
Connecting headphones to either of the PHONES jack
cuts off output to the speakers, which means you can
practice even late at night without bothering others. To
protect your hearing, make sure that you do not set the
volume level too high when using headphones.
NOTE
• Be sure to push the headphones plug into the
PHONES jacks as far as it will go. If you don’t, you
may hear sound from only one side of the
headphones.
• If the plug of the headphones you are using does not
match the PHONES jacks, use the applicable
commercially available adaptor plug.
• If you are using headphones that require an adaptor
plug, make sure you do not leave the adaptor
plugged in when you unplug the headphones. If you
do, nothing will sound from the speakers when you
play.
You can connect audio equipment or a music amplifier
to the digital piano and then play through external
speakers for more powerful volume and better sound
quality.
Connecting Audio Equipment (Figure 1)
Use commercially available connecting cords
(Standard Plug × 1, Pin Plugs × 2) to connect as shown
in Figure 1. Make sure that the end of the cord that
you connect to the digital piano is a stereo standard
plug. A monaural standard plug will result in output of
only one of the two stereo channels. Normally, you
should set the input selector of the audio equipment to
the terminal where the digital piano is connected (AUX
IN, etc.) Adjust volume using the digital piano’s
VOLUME controller.
Connecting a Music Amplifier (Figure 2)
Connect the connecting cord* to one of the types of
amplifiers shown in Figure 2.
Adjust volume using the digital piano’s VOLUME
controller.
Connecting Headphones
Stereo standard plug
PHONES jacks
Front
Connecting Audio Equipment
or an Amplifier
* Digital Piano: Stereo standard plug
Amplifier : Inputs signals for the left and right
channels. Not connecting either plug
will result in output of only one of the
two stereo channels.
INPUT 1
INPUT 2
Audio amplifier AUX IN jack, etc.
Guitar amplifier
Keyboard amplifier, etc.
Pin plug
Pin jack Standard plug
RIGHT (Red)
To either of the digital piano’s PHONES jack
Stereo standard plug
Pin plug (red)
Pin plug (white)
LEFT (White)
English
Connections
E-7
Use only accessories that are specified for use with this
digital piano.
Use of unauthorized accessories creates the risk of fire,
electric shock, and personal injury.
NOTE
• You can get information about accessories that are
sold separately for this product from the CASIO
catalog available from your retailer, and from the
CASIO website at the following URL.
http://world.casio.com/
Bundled and Optional
Accessories
E-8
Playing with Different Tones
The piano comes with 18 built-in tones.
• The names of the tones are marked above the keyboard keys to which they are assigned.
To select a tone
1.
Select the tone you want.
2.
Use the VOLUME controller to adjust the volume.
Selecting and Playing a Tone
SONG a
FUNCTION
METRONOME ELEC PIANO
GRAND PIANO
VOLUME
z To select GRAND PIANO (CONCERT or
MODERN) or ELEC PIANO
• Press one of the GRAND PIANO buttons
(CONCERT or MODERN) or the ELEC PIANO
button to select the one you want.
• The button lamp of the selected tone will light.
z To select one of the other tones
• While holding down the FUNCTION button,
press the keyboard key that corresponds to the
tone you want to select.
English
Playing with Different Tones
E-9
NOTE
• Of the digital piano’s 18 built-in tones, the first five
are grand piano tone. Each tone has its own
distinctive merits, so you should select the tone that
suits the song you are playing along with or your
own personal preferences. The CONCERT and
MODERN tones are assigned to buttons for quick
and easy selection.
* Feature that applies computer morphing
technology to enable seamless changes between
sounds sampled at various dynamics from a full
concert grand piano.
Bass Tones (BASS 1, BASS 2)
Selecting either of the two BASS (LOWER) tones (1 or
2) in step 1 of the above procedure will assign the
selected bass tone to the low range (left side) of the
keyboard. The high range (right side) will be assigned
the tone that was selected when you pressed the
BASS 1 or BASS 2 key.
• BASS 1 and BASS 2 let you effectively split the
keyboard between two different tones.
NOTE
• To return the keyboard to a single tone, select any
tone other than BASS 1 or BASS 2.
• You cannot select BASS 1 or BASS 2 when recording
to Track 2.
Tone Name Characteristics
CONCERT This is a full concert grand piano tone
that uses Linear Morphing* for
dynamic and natural tone changes.
This tone is designed to reproduce
damper, resonance, and other piano
nuances, which makes it ideal for
virtually any type of piano
performance.
MODERN This tone provides a bright grand piano
sound. The volume and timbre of this
tone is quick to respond to different
keyboard pressures, and it has
relatively deep reverb. This tone is a
good choice for dynamic and lively
performances.
CLASSIC This is a natural piano tone that closely
resembles the sound of an acoustic
piano. Though reverb and other flashy
effects are subdued for this tone,
resonance is more pronounced, which
enables expression of delicate nuances.
This tone is a good choice for lesson
and practice sessions.
MELLOW Warm and mellow piano tone
BRIGHT Bright and clear piano tone
Split Point
Low Range High Range
BASS 2 PIPE ORGAN
(Currently selected tone.)
E-10
Playing with Different Tones
Use the following procedure to layer two tones, so they
sound at the same time.
When specifying two tones for layering, first tone you
select will be the main tone, while the second tone will
be the layered tone.
1.
While holding down the FUNCTION button,
press down the keyboard key for the first tone
you want to layer and then the key for the
second tone.
Example: First press the HARPSICHORD key and
then the ELEC ORGAN 1 key.
2.
To unlayer the keyboard, select another tone
by pressing the GRAND PIANO button or by
using the procedure under “Selecting and
Playing a Tone” (page E-8).
NOTE
• You cannot layer the BASS 1 or BASS 2 tone with
another tone.
• You cannot perform the layer operation when
recording to Track 2.
To adjust the volume balance between
two layered tones
1.
While holding down the FUNCTION button,
use the keyboard keys shown below to adjust
the volume of the layered tones.
• To return the volume setting to its initial default, hold
down the FUNCTION button and press both of the
keys at the same time.
Layering Two Tones
HARPSICHORD
ELEC ORGAN 1
C1 C2 C3 C4 C5 C6 C7 C8
Initial default (Center)
Volume of the main tone
(First tone you selected)
Volume of the layered tone
(Second tone you selected)
English
Playing with Different Tones
E-11
1.
While holding down the FUNCTION button,
use the Reverb or Chorus keyboard key to
cycle through the available settings.
• Each press of the Reverb or Chorus keyboard key
causes the digital piano to beep according to which
setting is selected, as shown in the table below.
• Reverb
• Chorus
■ About DSP
DSP makes it possible to digitally produce complex
acoustic effects. The DSP is assigned to each tone
whenever you turn on digital piano power.
Your digital piano comes equipped with three pedals:
damper, soft, and sostenuto.
Pedal Functions
z Damper Pedal
Pressing the damper pedal while playing will cause the
notes you play to reverberate for a long time.
• When a GRAND PIANO tone (CONCERT/
MODERN/CLASSIC/MELLOW/BRIGHT) is
selected as the tone, pressing this pedal will cause
notes to reverberate (with damper resonance) just
like the damper pedal on an acoustic grand piano.
Half-pedal operation (pressing the pedal part way)
is also supported.
z Soft Pedal
Pressing this pedal while playing suppresses notes
played on the keyboard after the pedal was pressed,
and makes them sound softer.
z Sostenuto Pedal
Only the notes of the keys that are depressed when this
pedal is pressed are sustained until the pedal is
released.
Using Effects
Reverb : Makes your notes resonate.
Chorus: Adds more breadth to your notes.
Number of Beeps Setting
1 (long)
1 (short)
2
3
4
Off (OFF)
Room
Small Hall
Large Hall
Stadium
Number of Beeps Setting
1 (long)
1 (short)
2
3
4
Off (OFF)
Light Chorus
Medium Chorus
Deep Chorus
Flanger (whooshing effect)
ChorusReverb
Using the Digital Piano’s
Pedals
Soft pedal
Damper pedal
Sostenuto pedal
E-12
Playing with Different Tones
1.
Press the METRONOME button.
• This starts the metronome.
• The lamp above the SONG a button flash in time
with the metronome beat.
2.
To change the beat, hold down the
FUNCTION button as you press one of the
METRONOME BEAT keys to select a beat
setting.
• You can specify beats per measure value of 0, 2, 3, 4,
5, or 6. Specifying 0 as the setting plays a straight
click, without any chime. This setting lets you
practice with a steady beat.
3.
While holding down the FUNCTION button,
use the TEMPO keys to specify a tempo
value in the range of 20 to 255 beats per
minute.
• Each press of the + or – key raises or lowers the
tempo value by 1.
• You can use the value input keys (0 to 9) to enter a
specific three-digit. Be sure to input all three digits.
Example: To enter “96”, press keys 0, 9, 6.
4.
Press the METRONOME button or SONG
a button to turn off the metronome.
NOTE
• To return the tempo setting to the default tempo of
the currently selected Music Library tune, press the
+ and – keys at the same time in step 3. Pressing +
and – while recording will return the tempo value to
120.
To adjust the metronome volume
You can perform the following procedure at any time,
regardless of whether or not the metronome is
sounding.
1.
While holding down the FUNCTION button,
use the METRONOME VOLUME keys to
specify a volume value in the range of 0 to 42.
• For details about using the keyboard keys for
settings, see “Keyboard Keys Used for Configuring
Settings” on page E-21.
• Each press of the T or S key raises or lowers the
metronome volume value by 1.
NOTE
• To return to the initial default setting, press T and
S at the same time.
Using the Metronome
English
Playing with Different Tones
E-13
You can use the Duet Mode to split the piano’s
keyboard in the center so two people can play a duet.
The left and right side keyboards have virtually the
same range. The left pedal operates as the left side
damper pedal, while the right pedal is the right side
damper pedal.
This makes it possible to configure the keyboard so, for
example, the teacher can play on the left and the
student can follow along on the right. Or one person
can play the left hand part on the left, while another
plays the right hand part on the right.
Pedal Operation when Playing a Duet
NOTE
• Only the damper pedal for the right side keyboard
supports half-pedal operations.
1.
Select the piano tone you want to use for the
duet.
Example: GRAND PIANO (MODERN)
2.
While holding down the FUNCTION button,
press the METRONOME button to toggle
duet on and off.
IMPORTANT!
• You cannot use the Duet Mode while recording
(page E-16).
Changing the Octaves of the duet
keyboards
You can change the ranges of the left and right
keyboards in octave units from their initial default
settings. This comes in handy, for example, if the initial
default range is not enough when one person is
playing the left hand part and another person is
playing the right hand part.
1.
While holding down the FUNCTION and
METRONOME buttons, press the keyboard C
key that you want located at C4 (middle C) of
the left keyboard.
Example: Press the keyboard key of the leftmost C (C4)
will assign the range shown below.
2.
While holding down the FUNCTION and
METRONOME buttons, press the keyboard C
key that you want located at C4 (middle C) of
the right keyboard.
NOTE
• You can return the keyboards to their initial default
ranges by exiting and then re-entering the Duet
Mode.
Playing a Piano Duet
C3 C4 C5 C6 C3 C4 C5 C
6
Keyboard
Split point
Left keyboard Right keyboard
(middle C)(middle C)
Left side damper pedal
Left and right side
damper pedal
Right side damper pedal
(Half-pedal operation
supported)
C4 C5 C6 C7 C3 C4 C5 C6
Left keyboard Right keyboard
(Pressed key)
1 octave higher than initial
setting
Unchanged
E-14
Playing Back Built-in Songs
Your digital piano comes with a Music Library of 60
built-in tunes. You can play all 60 tunes in sequence,
from beginning to end.
IMPORTANT!
• After you select a built-in song, it can take a number
of seconds for the song data to be loaded. While the
data is being loaded, the keyboard keys and button
operations will be disabled. If you are playing
something on the keyboard, the following operation
will cause output to stop.
1.
While holding down the FUNCTION button,
press the SONG a button.
• This will start repeat demo playback of the built-in
songs in sequence, from 01 through 60.
• You can play along with a song on the keyboard as it
is playing. The tone assigned to the keyboard is the
one that is preset for the song that is playing.
2.
To change demo playback to a different song,
hold down the FUNCTION button as you use
the SONG SELECT keys to specify a song
number.
• Each press of the + or – key raises or lowers the song
number by 1.
• You can use the value input keys (0 to 9) to enter a
specific two-digit song number. Be sure to input both
digits.
Example: To select song 08, enter 0 and then 8.
3.
Press the SONG a button again to stop
built-in song play.
NOTE
• The tune selection and playback stop operations
described above are the only operations that are
possible during demo tune play.
SONG a
FUNCTION
RECORDER
Playing Back All of the Built-in
Songs
English
Playing Back Built-in Songs
E-15
The Music Library includes both built-in songs (01 to
60), plus songs (61 to 70) that have been saved to digital
piano memory from a computer*. You can use the
procedure below to select one of these songs and play it
back.
* You can download music data from the Internet and
then transfer it from your computer to digital piano
memory. See “Transferring Song Data with a
Computer” on page E-26 for more information.
1.
Find the song number of the song you want to
play in the song list on page A-1.
2.
To change to another song, hold down the
FUNCTION button as you use the SONG
SELECT keys to specify a song number.
• For information about how to perform this step, see
the note under step 2 of the procedure under
“Playing Back All of the Built-in Songs” on page E-14.
3.
Press the SONG a button.
• This starts the playback of the song.
4.
To stop playback, press the SONG a
button again.
• Playback will stop automatically when the end of the
song is reached.
NOTE
• Pressing the + and – keys at the same time will select
song number 01.
• You also can adjust the playback tempo and volume
of the song. See “Configuring Settings with the
Keyboard” on page E-20 for more information.
You can turn off the left hand part or right hand part of
a song and play along on the piano.
NOTE
• The Music Library includes a number of duets.
While a duet is selected, you can turn off the first
piano <Primo> or second piano <Secondo> tone
and play along with the song.
PREPARATION
• Select the song you want to practice and adjust the
tempo. See “Configuring Settings with the
Keyboard” on page E-20.
• A number of tunes have tempo changes part way
through in order to produce specific musical effects.
1.
While holding down the FUNCTION button,
press the RECORDER (L/R) button to select
the part you want to turn off.
• Pressing a button toggles its part on (button lamp on)
and off (button lamp off).
2.
Press the SONG a button.
• This starts playback, without the part you turned off
in step 1.
3.
Play the missing part on the keyboard.
4.
To stop playback, press the SONG a
button again.
Playing Back a Specific Music
Library Song
Practicing with a Music Library
Song
Left hand Right hand
Both parts on
Right hand
part off
Left hand
part off
E-16
Recording and Play Back
You can store the notes you play in digital piano
memory for later playback.
A track is a container of recorded data, and a song
consists of two tracks: Track 1 and Track 2. You can
record each track separately and then combine them so
they play back together as a single song.
Memory Capacity
• You can record approximately 5,000 notes in digital
piano memory.
• The RECORDER button lamp will flash at high
speed when memory runs low.
• Recording stops automatically if the number of
notes in memory exceeds the maximum.
Recorded Data
• Keyboard play
• Tone used
• Pedal operations
• Reverb and chorus settings (Track 1 only)
• Tempo setting (Track 1 only)
• Layer setting (Track 1 only)
• Split setting (Track 1 only)
• Temperament and base note settings (Track 1 only)
• Octave shift setting (Track 1 only)
Recording Data Storage
• Starting a new recording deletes any data that was
previously recorded in memory.
• If power to the Digital Piano is cut off while
recording is in progress, everything you recorded up
to that point will be deleted. Take care so power is
not turned off accidentally during recording
operations.
IMPORTANT!
• CASIO COMPUTER CO., LTD. takes no
responsibility for any damages, lost profits, or claims
by third parties arising from the deletion of recorded
data due to malfunction, repair, or for any other
reason.
Using the RECORDER Button
Each press of the RECORDER button cycles through
the recording options in the sequence shown below.
SONG a
FUNCTION
RECORDER
METRONOME
Tracks
Track 1 Record
While playing
back. . .
Track 2 Record
Song
Lit Flashing Off
Playback
Standby
Record
Standby
Normal
English
Recording and Play Back
E-17
After recording to either of the tracks of a song, you can
record to the other track while listening to playback
what you recorded in the first track.
1.
Press the RECORDER button twice so its
lamp is flashing.
• At this time the L lamp will flash to indicate that the
digital piano is standing by for recording to Track 1.
2.
To change the recording track, hold down the
FUNCTION button as you press the
RECORDER (L/R) button.
• Make sure that the indicator lamp for the record track
is flashing.
Track 1: L lamp
Track 2: R lamp
Example: Track 1 selected
3.
Select the tone and effects (Track 1 only) you
want to use in your recording.
• Tone (page E-8)
• Effects (page E-11)
NOTE
• If you want the metronome to sound while you are
recording, configure the beat and tempo settings,
and then press the METRONOME button. See
“Using the Metronome” on page E-12 for more
information.
4.
Start playing something on the keyboard.
• Recording will start automatically.
5.
To stop recording, press the SONG a
button.
• This will cause the RECORDER button lamp and the
lamp of the track you recorded to change from
flashing to lit.
• To play back the track you just recorded, press the
SONG a button.
6.
After you are finished recording or playing
back, press the RECORDER button so its
lamp goes out.
To record to a specific track of
a song
E-18
Recording and Play Back
1.
Press the RECORDER button so its lamp is
lit.
2.
While holding down the FUNCTION button,
press the RECORDER (L/R) button to select
the track you want to play back while
recording.
3.
Press the RECORDER button so its lamp is
flashing.
• This will cause the L lamp to flash.
4.
While holding down the FUNCTION button,
press the RECORDER (L/R) button to select
the track you want to record.
• Make sure that the indicator lamp for the record track
is flashing.
Example: To listen to playback of Track 1 as you record
to Track 2
5.
Select the tone and effects (Track 1 only) you
want to use for your recording.
6.
Press the SONG a button or play
something on the keyboard.
• This will start both playback of the recorded track
and recording to the other track.
7.
To stop recording, press the SONG a
button.
1.
Press the RECORDER button so its lamp is
lit.
NOTE
• When a song has something recorded in both tracks,
you can turn off one track and play back just the
other track, if you want.
2.
Press the SONG a button.
• This starts playback of the song and/or track you
selected.
NOTE
• You can change the tempo setting as a track is
playing.
• Press the SONG a button again to stop playback.
To record to one track of a
song while listening to the
playback of the other track
Lit (Play) Flashing (Record Standby)
Playing Back from Digital
Piano Memory
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/