JVC GR-AX930U User manual

GR-AX930

COMPACT VHS CAMCORDER

INSTRUCTIONS

LYT0050-001B

Compact VHS

For Customer Use:

Enter below the Model No. and Serial

No. which is located on the bottom of

cabinet. Retain this information for

future reference.

Model No.

Serial No.

2 EN

Dear Customer,

Thank you for purchasing the JVC Compact VHS

camcorder. Before use, please read the safety

information and precautions contained in the

following pages to ensure safe use of your new

camcorder.

Using This Instruction Manual

• All major sections and subsections are listed in the

Table Of Contents (

Z pg. 7).

• Notes appear after most subsections. Be sure to read

these as well.

• Basic and advanced features/operation are separated

for easier reference.

It is recommended that you . . .

..... refer to the Index (Z pgs. 53 – 56) and

familiarize yourself with button locations, etc.

before use.

..... read thoroughly the Safety Precautions and Safety

Instructions that follow. They contain extremely

important information regarding the safe use of

your new camcorder.

SAFETY

PRECAUTIONS

The AA-V15U AC Power Adapter/Charger should

be used with:

AC 120 V`, 60 Hz in the USA and Canada,

AC 110 – 240 V`, 50/60 Hz in other countries.

CAUTION (applies to the AA-V15U)

TO PREVENT ELECTRIC SHOCK MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION (s’applique à l’AA-V15U)

POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE

LA PRISE ET POUSSER JUSQU’AU FOND.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE

THIS UNIT TO RAIN OR

MOISTURE.

Warning on lithium battery

The battery used in this device may present a fire

or chemical burn hazard if mistreated. Do not

recharge, disassemble, heat above 100°C (212°F)

or incinerate.

Replace the battery with Maxell, Panasonic

(Matsushita Electric), Sanyo or Sony CR2025; use

of another battery may present a risk of fire or

explosion.

n Dispose of used battery promptly.

n Keep away from children.

n Do not disassemble and do not dispose of in fire.

You are recommended to carefully read the cautions

on pages 57 and 58 before use.

NOTES:

●

The rating plate (serial number plate) and safety

caution are on the bottom and/or the back of the

main unit.

●

The rating plate (serial number plate) of the AC

Power Adapter/Charger is on its bottom.

This Class B digital apparatus meets all require-

ments of the Canadian Interference – Causing

Equipment Regulations.

“Cet appareil numérique de la classe B respecte

toutes les exigences du Règlement sur le matériel

brouilleur du Canada.”

This camcorder is designed to be used with NTSC-

type color television signals. It cannot be used for

playback with a television of a different standard.

However, live recording and viewfinder playback

are possible anywhere. Use the BN-V12U/V18U/

V22U/V25U battery packs and, to recharge them,

the provided multi-voltage AC Power Adapter/

Charger. (An appropriate conversion adapter may

be necessary to accommodate different designs of

AC outlets in different countries.)

ATTENTION:

The product that you have purchased is powered

by a rechargeable battery. The battery is recycla-

ble. At the end of its useful life, under various state

and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste officials for details in

your area for recycling options or proper disposal.

EN 3

5. Ventilation

Slots and openings in the cabinet are provided for

ventilation. To ensure reliable operation of the product

and to protect it from overheating, these openings must

not be blocked or covered.

•Do not block the openings by placing the product on

a bed, sofa, rug or other similar surface.

•Do not place the product in a built-in installation

such as a bookcase or rack unless proper ventilation

is provided or the manufacturer’s instructions have

been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

ANTENNA INSTALLATION

INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to

the product, be sure the antenna or cable system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810

of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding

of the mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna discharge

unit, connection to grounding electrodes, and

requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning

storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will

prevent damage to the product due to lightning and

power-line surges.

3. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light

or power circuits, or where it can fall into such power

lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from

touching such power lines or circuits as contact with

them might be fatal.

IMPORTANT PRODUCT

SAFETY INSTRUCTIONS

Electrical energy can perform many useful func-

tions. But improper use can result in potential

electrical shock or fire hazards. This product has

been engineered and manufactured to assure your

personal safety. In order not to defeat the built-in

safeguards, observe the following basic rules for its

installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions

marked on your product and its operating instruc-

tions. For your safety, please read all the safety and

operating instructions before you operate this

product and keep this manual for future reference.

INSTALLATION

1. Grounding or Polarization

(A) Your product may be equipped with a polarized

alternating-current line plug (a plug having one

blade wider than the other). This plug will fit into

the power outlet only one way. This is a safety

feature.

If you are unable to insert the plug fully into the

outlet, try reversing the plug. If the plug should still

fail to fit, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of

the polarized plug.

(B) Your product may be equipped with a 3-wire

grounding-type plug, a plug having a third

(grounding) pin. This plug will only fit into a

grounding-type power outlet. This is a safety

feature.

If you are unable to insert the plug into the outlet,

contact your electrician to replace your obsolete

outlet. Do not defeat the safety purpose of the

grounding-type plug.

2. Power Sources

Operate your product only from the type of power

source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. If your

product is intended to operate from battery power, or

other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a

risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are

not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to

cords at plugs, convenience receptacles, and the point

where they exit from the product.

ANTENNA

LEAD IN WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION

810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE

EQUIPMENT

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

GROUND CLAMP

4 EN

USE

1. Accessories

To avoid personal injury:

•Do not place this product on an unstable cart,

stand, tripod, bracket or table. It may fall, causing

serious injury to a child or adult, and serious

damage to the product.

•Use only with a cart, stand, tripod, bracket, or

table recommended by the manufacturer or sold

with the product.

•Use a mounting accessory recommended by the

manufacturer and follow the manufacturer’s

instructions for any mounting of the product.

•Do not try to roll a cart with small casters across

thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved

with care. Quick stops, excessive force, and uneven

surfaces may cause the product and cart combina-

tion to overturn.

3. Water and Moisture

Do not use this product

near water—for example,

near a bath tub, wash

bowl, kitchen sink or

laundry tub, in a wet

basement, or near a

swimming pool and the

like.

4. Object and Liquid Entry

Never push objects of any kind into this product

through openings as they may touch dangerous

voltage points or short-out parts that could result in

a fire or electric shock. Never spill liquid of any

kind on the product.

5. Attachments

Do not use attachments not recommended by the

manufacturer of this product as they may cause

hazards.

6. Cleaning

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat

sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce

heat.

SERVICING

1. Servicing

If your product is not operating correctly or exhibits

a marked change in performance and you are

unable to restore normal operation by following the

detailed procedure in its operating instructions, do

not attempt to service it yourself as opening or

removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to

qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

a. When the power supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the product to its normal operation.

e. If the product has been dropped or damaged in

any way.

f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the

service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock or

other hazards.

4. Safety Check

Upon completion of any service or repairs to this

product, ask the service technician to perform safety

checks to determine that the product is in safe

operating condition.

PORTABLE CART WARNING

(Symbol provided by RETAC)

EN 5

2

1

3

Using the battery pack

1

Hook-on the battery pack’s top end to the

camcorder. (Charging procedure, Z pg. 8)

2 Push in the battery pack until it locks into

place.

To remove the battery pack

Slide BATT. RELEASE and pull out the battery

pack.

QUICK OPERATION GUIDE

1 Set the Power Switch to “PLAY”.

2 Press REW.

— The tape will automatically stop at the

beginning of the tape.

3 Press PLAY/PAUSE.

— Playback starts and the playback picture

appears.

•To stop playback, press STOP.

(For more details,

Z pg. 38.)

Or simply play back the tape on a VHS

VCR using the Cassette Adapter (VHS

Playpak). Z pg. 36

SUPPLY POWER

INSERTING A VIDEO

CASSETTE

PLAYBACK

SHOOTING

1 Slide EJECT to open the cassette holder.

2 Insert a video cassette.

3 Press PUSH to close the cassette holder.

(For more details, Z pg. 13)

2

1

3

EJECT

PUSH

2

1

Push in.

Hook on.

BATT. RELEASE

1 Slide the LENS COVER Open/Close Switch

to open the lens cover.

2 Set the Power Switch to “CAMERA”.

— The power indicator will light and an

image will appear.

3 Press the Recording Start/Stop Button.

— Recording starts.

•To stop recording temporarily, momentarily

press the Recording Start/Stop Button once

again.

(For more details,

Z pgs. 16, 17)

PLAY/PAUSE

REW

STOP

Set to “PLAY”

3

1

2

Recording Start/Stop Button

Set to “CAMERA”

LENS COVER

Open/Close

Switch

6 EN

MAJOR FEATURES

REMEMBER

Program AE with Special

Effects (

Z pg. 22)

n Auto Mode Lock

n Auto Mode Release

n Electronic Fog Filter

n ND Effect

n Sepia

n Twilight

n Sports

n Nega/Posi

n 1/2000 sec. High Speed Shutter

The Logical Choice

The only compact video

cassettes that can be

used with your VHS VCR*

Program Manager II

(Z pg. 22 – 35)

Program AE with Special Effects,

Fade/Wipe, Wide, Super LoLux,

Instant Title, Menu Adjustment

(Focus, Exposure Control and so on.)

Integrated Auto Light

(

Z pg. 21)

Picture Stabilizer (Z pg. 19)

Digital Hyper Zoom

(

Z pg. 18)

Zoom-in

Zoom-out

PROVIDED ACCESSORIES

•AC Power Adapter/

Charger AA-V15U

•Remote Control

Unit RM-V705U

•Shoulder Strap

•DC Cord

•Cassette Adapter

(VHS Playpak)

C-P7U

•Lithium Battery

CR2025 x 2

(for clock operation

and remote control

unit)

•Battery Pack

BN-V18U

Cassettes marked

can be used with this camcorder.

EN 7

CONTENTS

GETTING STARTED

8

Power ..................................................................................... 8

Clock (Lithium) Battery Insertion/Removal........................................ 10

Date/Time Setting .................................................................... 11

Recording Mode Setting .............................................................. 12

Tape Length Setting ................................................................... 12

Loading/Unloading A Cassette ...................................................... 13

Grip Adjustment ....................................................................... 14

Viewfinder Adjustment ............................................................... 14

Shoulder Strap Attachment........................................................... 15

Tripod Mounting ....................................................................... 15

RECORDING

16

Basic Recording ........................................................................ 16

Basic Features ......................................................................... 18

Advanced Features .................................................................... 22

PLAYBACK

36

Using The Cassette Adapter.......................................................... 36

Basic Connections...................................................................... 37

Basic Playback ......................................................................... 38

Features ................................................................................ 39

TAPE DUBBING

41

USING REMOTE CONTROL UNIT

42

Random Assemble Editing ............................................................ 44

Insert Editing ........................................................................... 48

Audio Dubbing ......................................................................... 49

USER MAINTENANCE

50

TROUBLESHOOTING

51

INDEX

53

Viewfinder Indications ................................................................ 53

Controls ................................................................................. 54

Connectors.............................................................................. 54

Indicators ............................................................................... 54

Other Parts............................................................................. 54

Terms .................................................................................... 56

CAUTIONS

57

SPECIFICATIONS

59

OPTIONAL ACCESSORIES

59

ESPAÑOL

60

FOR SERVICING (Only in U.S.A.)

62

WARRANTY (Only in U.S.A.)

63

GETTING STARTED

RECORDING

PLAYBACK

8 EN

GETTING STARTED

Power

This camcorder’s 3-way power supply system lets you

choose the most appropriate source of power.

NOTES:

●

No function is available without power supply.

●

Use only specified power supply.

●

Do not use provided power supply units with other

equipment.

CHARGING THE BATTERY PACK

SUPPLY POWER

1

Connect the charger’s AC power cord to a wall

outlet.

ATTACH BATTERY PACK

2

Align the marks and slide the battery pack in the

direction of the arrow until it locks in place.

•The CHG. indicator begins blinking to indicate

charging has started.

DETACH BATTERY PACK

3

When the CHG. indicator stops blinking but stays

lit, charging is finished. Slide the battery pack

opposite the direction of the arrow.

ATTENTION:

Before detaching the power source,

make sure that the camcorder’s power

is turned off. Failure to do so can result

in a camcorder malfunction.

CHG. (charge)

indicator

Marks

To AC outlet

REFRESH indicator

REFRESH switch

Push in.

Hook on.

BATT. RELEASE

1

2

REFRESH

The AC power adapter features a REFRESH

function that allows you to fully discharge

the battery pack before recharging. Perform

the REFRESH function after no less than 5

chargings.

To discharge the battery . . .

..... attach the battery pack to the adapter

as shown in the above illustration.

Then push REFRESH. The REFRESH

indicator lights when discharging

starts, and goes out when discharging

is complete.

USING THE BATTERY PACK

ATTACH BATTERY PACK

1

Hook its top end to the camcorder and push the

battery pack in until it locks in place.

DETACH BATTERY PACK

2

Slide BATT. RELEASE and pull out the battery pack.

BATT. PACK CHARGE DISCHARGE

BN-V12U approx. 1 hr. 10 min.

approx.

3 hrs. 30 min.

BN-V18U approx. 1 hr. 40 min.

approx.

5 hrs. 30 min.

BN-V22U approx. 2 hrs. 10 min. approx. 7 hrs.

BN-V25U approx. 2 hrs. 40 min. approx. 10 hrs.

BATT. PACK

Approximate recording time (unit: min.)

BN-V12U 75 ( 40 )

BN-V18U 110 ( 65 )

BN-V22U 150 ( 90 )

BN-V25U 200 ( 120 )

( ) : when the video light is on.

EN 9

CHARGE MARKER

A charge marker is provided on the battery pack to

help you remember whether it has been charged or

not. Two colors are provided (red and black)—you

choose which one means charged and which

means discharged.

•The battery pack BN-V18U does not have a

charge marker.

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery

Charger/Adapter (connect as shown in the

illustration to the left).

NOTES:

●

When using the car battery, leave the engine

idling.

●

The optional Car Battery Charger (BH-V3U) can

also be used to charge the battery pack.

●

When using the optional Car Battery Charger or

Car Battery Cord (AP-V7U), refer to the respective

instruction booklet.

USING AC POWER

Use the AC Power Adapter (connect as shown in

the illustration to the left).

NOTE:

The supplied AC Power Adapter/Charger features

automatic voltage selection in the AC range from

110 V to 240 V.

To DC

IN jack

AC Power Adapter/

Charger AA-V15U

To AC outlet

DC OUT

terminal

DC cord

To car’s

cigarette

lighter socket

Car Battery Cord

AP-V7U (optional)

Car Battery

Charger/Adapter

BH-V3U (optional)

NOTES:

●

The recording time per charge is affected by such factors as the time spent in Record-Standby mode and

the frequency of zooming. It is safer to have spare battery packs.

●

Charging times noted on page 8 are for fully discharged battery pack, and discharging times are for fully

charged battery pack.

●

Charging and discharging times vary according to the ambient temperature and the status of the battery pack.

●

Remember to set the charge marker after charging a battery pack or after detaching a discharged one from

your camcorder.

●

Perform the REFRESH function after no less than 5 chargings.

●

While the AC Power Adapter/Charger’s power cord is disconnected from the AC outlet, it is possible to

discharge the battery by pressing the REFRESH switch. During that time, the AC Power Adapter/Charger

does not charge the battery. When disharging is complete, detach the battery from the AC Power Adapter/

Charger to store it.

●

High temperatures can damage the battery pack, so use only where good ventilation is available. Don’t

allow it to discharge in container, such as a bag.

●

If you stop recharging or discharging part way through, make sure to remove the battery pack before

unplugging the adapter’s AC cord.

●

Remove the battery pack from the adapter immediately after discharging.

●

To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

●

Make sure you unplug the DC cord before charging or discharging the battery pack.

●

The CHG. indicator may not light properly with a brand new battery pack, or with one that’s been stored

for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHG.

indicator should blink during recharging. If not, contact your nearest JVC dealer.

Charge marker

10 EN

GETTING STARTED

(cont.)

Clock (Lithium) Battery Insertion/Removal

This battery is necessary for clock operation and to

perform date/time settings.

SWITCH OFF POWER

1

Switch off the unit’s power and remove the power

supply unit.

OPEN COVER

2

Open the clock battery compartment cover while

pressing the release tab.

REMOVE BATTERY (when replacing)

3

Insert a pointed, non-metallic object between the

battery and the compartment (

A

) and pull the

battery out.

INSERT BATTERY

4

Ensure that the plus (+) side is up and insert a

CR2025 lithium battery and push it in.

CLOSE COVER

5

Close the compartment cover until it clicks in place.

NOTE:

See “SAFETY PRECAUTIONS” (

Z

pg. 2) for information

on safe handling of lithium batteries.

A

EN 11

MENU

4

MENU END

FOCUS

EXPOSURE

DATE TIME

TELE MACRO

TAPE LENGTH

M. W. B.

ZOOM SPEED

4

MENU END

FOCUS

EXPOSURE

DATE TIME

TELE MACRO

TAPE LENGTH

M. W. B.

ZOOM SPEED

4

YEAR

MONTH

DAY

TIME

EXIT

1998

JAN

1

PM 12:00

AUTO

DEC

OFF

T30

AUTO

FAST

25.98

AUTO

JAN

OFF

T30

AUTO

FAST

1.98

MENU

Jog Dial

Select Dial

Viewfinder

Menu Screen

DATE/TIME Setting Menu

12-hour

indication with

AM or PM

Date/Time Setting

ACCESS MENU SCREEN

1

First set the Power Switch to “CAMERA”. Turn the

Select Dial to any position except AUTO LOCK,

then press the MENU Jog Dial.

SELECT FUNCTION

2

Rotate the MENU Jog Dial to move the highlight bar

to “DATE/TIME”, then press it. The DATE/TIME

Setting Menu appears.

•If you decide you want to return the date and time

to the previous settings, rotate the MENU Jog Dial

to move highlight bar to “EXIT” and press it, then

go to step 6.

•If you want to set only the time without changing

the date, go to step 4.

SET DATE

3

Rotate the MENU Jog Dial to move the highlight bar

to the item you want to set and then press it. When

the setting begins blinking, rotate the MENU Jog

Dial until the correct setting appears and then press

it. The setting stops blinking.

•Repeat this procedure until you’re satisfied with

the Date settings (“YEAR”, “MONTH” and “DAY”).

SET TIME

4

Rotate the MENU Jog Dial to move the highlight bar

to “TIME” and then press it. When the hour setting

begins blinking, rotate the MENU Jog Dial until the

correct setting appears and then press it. When the

hour setting stops blinking and the minute setting

begins blinking, rotate the MENU Jog Dial until the

correct setting appears and then press it. The minute

setting stops blinking.

START CLOCK OPERATION

5

When none of these settings (YEAR, MONTH, DAY,

TIME) blinks, rotate the MENU Jog Dial to move the

highlight bar to “EXIT”, and press it. The Menu

Screen appears and “MENU END” is highlighted.

CLOSE MENU

6

Press the MENU Jog Dial.

NOTE:

To display the date and time in the viewfinder and on a

connected TV, see “Date/Time Insert” (

Z

pg. 20).

12 EN

MENU

4

MENU END

FOCUS

EXPOSURE

DATE TIME

TELE MACRO

TAPE LENGTH

M. W. B.

ZOOM SPEED

4

MENU

4

MENU END

FOCUS

EXPOSURE

DATE TIME

TELE MACRO

TAPE LENGTH

M. W. B.

ZOOM SPEED

4

AUTO

DEC

OFF

T20

AUTO

FAST

25.98

SP

T40

T20

T30

T40

EXIT

TAPE LENGTH

AUTO

DEC

OFF

T40

AUTO

FAST

GETTING STARTED

(cont.)

SP/EP Recording

Mode Button

Select Dial

MENU Jog Dial

Viewfinder

Tape length

indicator

Recording

mode

indicator

Menu Screen

TAPE LENGTH Setting Menu

Recording Mode Setting

Set depending on your preference.

SET RECORDING MODE

1

First set the Power Switch to “CAMERA”. Press SP/EP

Button for more than 1 second. “SP” (Standard Play)

provides higher picture and sound quality and is

better for dubbing, while “EP” (Extended Play) is

more economical, providing three times as the

recording time.

NOTE:

If the recording mode is switched during recording, the

playback picture will be blurred at the switching point.

Tape Length Setting

Set the tape length according to the length of the tape

used.

ACCESS MENU SCREEN

1

First set the Power Switch to “CAMERA”. Turn the

Select Dial to any position except AUTO LOCK,

then press the MENU Jog Dial.

SELECT FUNCTION

2

Rotate the MENU Jog Dial to move the highlight bar

to “TAPE LENGTH”, then press it. The TAPE

LENGTH Setting Menu appears.

SET TAPE LENGTH

3

Rotate the MENU Jog Dial to move the highlight bar

to the correct setting. T20=20 minutes of recording

time, T30=30 minutes, and T40=40 minutes (in SP).

•If you decide you want to return the tape length to

the previous setting, rotate the MENU Jog Dial to

move the highlight bar to “EXIT”.

CLOSE MENU

4

Press the MENU Jog Dial. The Menu Screen

reappears and the highlight bar is on “MENU END”.

Then press the MENU Jog Dial again to close the

Menu Screen.

NOTES:

●

The displayed tape remaining time (

Z

pg. 17) is

correct only if the correct tape length has been

selected.

●

Once you have set the tape length, it remains un-

changed even if the Select Dial is returned to AUTO

LOCK.

EN 13

1

2

3

Loading/Unloading A Cassette

OPEN CASSETTE HOLDER

1

Slide EJECT until the holder opens. Do not use force

to open.

INSERT/REMOVE CASSETTE

2

Make sure the label is facing outward.

CLOSE CASSETTE HOLDER

3

Press PUSH and make sure the holder is closed and

locked.

NOTES:

●

A cassette holder can’t be opened unless a power

supply is attached.

●

Make sure that the tape is not slack when loading the

cassette. If there is any slack, turn the gear on the

cassette in the direction of the arrow to take up the

slack.

●

Make sure the Erase Protection tab is in the position

that allows recording. If not, slide the tab. Some

cassettes have removable tabs. If the tab has been

removed, cover the hole with adhesive tape.

●

The cassette holder can’t be opened while the

camcorder is in the record mode.

Erase Protection Gear

Turn to take

up slack.

14 EN

GETTING STARTED

(cont.)

Grip Adjustment

EXPAND LOOP

1

Separate the Velcro strip.

INSERT HAND

2

Pass your right hand through the loop and grasp the

grip.

ADJUST STRAP LENGTH

3

Adjust so your thumb and fingers can easily operate

the Recording Start/Stop Button and Power Zoom

Button. Refasten the Velcro strip.

Viewfinder Adjustment

POSITION VIEWFINDER

1

Adjust the viewfinder manually for best viewability

(see illustration at left).

SELECT MODE

2

Set the Power Switch to CAMERA.

ADJUST DIOPTER

3

Turn the Diopter Adjustment Control until the

indications in the viewfinder are clearly focused.

Power Zoom Button

1

2

3

Recording Start/Stop Button

Set POWER to “CAMERA”.

EN 15

Shoulder Strap Attachment

ATTACH STRAP

1

Following the illustration at left, thread the strap

through the top of the eyelet 1, then fold it back

and thread it through the buckle 2. Repeat the

procedure to attach the other end of the strap to the

other eyelet 3, making sure the strap isn’t twisted.

ADJUST LENGTH

2

Adjust as shown in the illustration at left 1.

CAUTION:

When using a tripod, be sure to open and extend

its legs fully to stabilize the camcorder. To

prevent damage to the unit caused by falling

over, do not use a small-sized tripod.

2

3

1

Tripod Mounting

ALIGN AND TIGHTEN

1

Align the screw and camera direction stud on the

tripod with the camera’s mounting socket and stud

hole. Then tighten the screw.

16 EN

RECORDING

Basic Recording

NOTE:

You should already have performed the procedures listed

below. If not, do so before continuing.

●

Power (

Z

pg. 8)

●

Recording Mode/Tape Length Setting (

Z

pg. 12)

●

Grip Adjustment (

Z

pg. 14)

LOAD A CASSETTE

1

Slide EJECT to open the cassette holder, then insert

the cassette with the label facing out. Press PUSH to

ensure the holder is closed and locked.

ENTER RECORD-STANDBY MODE

2

Slide the LENS COVER Open/Close Switch to open

the lens cover, then set the Power Switch to

CAMERA.

•The power indicator lights and the camcorder

enters the Record-Standby mode.

•The scene you’re aimed at appears on the

viewfinder screen, with the word “PAUSE”

superimposed upon it.

START SHOOTING

3

Press the Recording Start/Stop Button.

•“

REC

” appears in the viewfinder while recording is

in progress.

LENS COVER Switch

Power

indicator

Start/Stop Button

Power Switch

Tally lamp

(lights while recording

is in progress)

EN 17

STOP RECORDING

4

Press the Recording Start/Stop Button again to stop

recording.

•The camcorder re-enters the Record-Standby

mode.

NOTES:

●

A cassette holder can’t be opened unless a power supply

is attached.

●

There may be a delay after you slide EJECT until the

holder opens. Do not use force.

●

The displayed remaining time is approximate.

●

The time required to calculate the remaining tape

length, and the accuracy of the calculation, may vary

according to the type of tape used.

●

The tape remaining time indicator is correct only if the

correct tape length has been selected (

Z

pg. 12).

●

“TAPE END” appears when the tape reaches its end,

and the power goes off automatically if left in this

condition for 5 minutes. “TAPE END” also appears

when a cassette whose tape is already at its end is

loaded.

●

If the Record-Standby mode continues for 5 minutes

without performing Zoom or any other operations, the

camcorder’s power shuts off automatically. Set the

Power Switch to “POWER OFF”, and then back to

“CAMERA” to turn the camcorder on again.

●

If the Recording Start/Stop Button is pressed after the

Record-Standby mode has continued for over

5 minutes, recording may not start immediately.

●

If you’re recording on a cassette from the middle (such

as when a tape is removed and re-inserted during

recording), use the Retake function (

Z

pg. 19) to find

the end of the last recording so you don’t erase any of

it.

●

The LENS COVER warning blinks for about 5 seconds

when the camcorder is turned on when the cover is

closed.

25MIN

120MIN

119MIN

3MIN

2MIN

1MIN

0MIN

MIN

Tape remaining time indicator

(Blinking)

Start/Stop Button

(Now calculating)

18 EN

RECORDING

Basic Features

FEATURE: Zooming

PURPOSE: To produce the zoom in/out effect, or

an instantaneous change in image

magnification.

Digital circuitly doubles the maximum

22x magnification offered by optical

zoom. This system is called Digital Zoom.

OPERATION:

Zoom In

Press the “T” of the Power Zoom Button.

Zoom Out

Press “W” of the Power Zoom Button.

n Zooming speed is available. A total of

4 zoom speeds are available. 2 speeds

can be selected depending on how

hard the Power Zoom Button is

pressed (press the button fully for

regular-speed, press it lightly for slow-

speed), while 2 speed levels (FAST/

SLOW) can be selected in the ZOOM

SPEED Menu depending on the overall

speed you prefer.

The combinations of zoom speeds are

shown in the chart below.

Changing the ZOOM SPEED in the

Menu

1) Set the Select Dial to any position

except AUTO LOCK and press the

MENU Jog Dial. The Menu Screen

appears.

2) Rotate the MENU Jog Dial to move

the highlight bar to “ZOOM SPEED”,

then press it. The ZOOM SPEED

Setting Menu appears.

3) Rotate the MENU Jog Dial to move

the highlight bar to the desired speed

and press it twice. The Menu Screen

disappears and setting is completed.

NOTES: ●

Focusing may become unstable

during Zooming. In this case, set the

zoom while in Record-Standby, lock

the focus by using the manual focus

(

Z

pg. 31), then zoom in or out in

Record mode.

●

The zoom level indicator (

5

) moves

during zoom. Once the zoom level

indicator reaches the top of the zoom

indicator bar, all magnification from

that point is through digital

processing.

●

During Digital Zoom, the quality of

image may suffer. To deactivate Digital

Zoom, set “D.ZOOM” to “OFF” in the

Menu Screen (

Z

pg. 29).

MENU

4

MENU END

FOCUS

EXPOSURE

DATE TIME

TELE MACRO

TAPE LENGTH

M. W. B.

ZOOM SPEED

4

AUTO

JAN

OFF

T30

AUTO

FAST

1.98

ZOOM SPEED

FAST

SLOW

EXIT

Zoom-in

Zoom-out

ZOOM SPEED Setting Menu

Menu Screen

Zooming Speed ( 1 – 4 in order of speed)

“ZOOM SPEED”

in the Menu

Screen

: when the Select Dial is set to AUTO LOCK.

Pressing the Power Zoom Button

fully lightly

FAST 1 (fastest) 3

SLOW 2 4 (slowest)

Zoom indicator bar

Zoom Level

indicator

Power Zoom button

Select Dial

MENU Jog Dial

Viewfinder

EN 19

FEATURE: Quick Review

PURPOSE: To check the end of the last

recording.

OPERATION: 1) Press “ ” and release quickly

during the Record-Standby mode.

n Tape is rewound for about 2

seconds and played back

automatically, then pauses in

Record-Standby mode for the

next shot.

NOTE:

Distortion may occur at start of

playback. This is normal.

FEATURE: Retake

PURPOSE: To re-record certain segments.

OPERATION: 1) Make sure the camcorder is in the

Record-Standby mode.

2) Press either RETAKE button to

reach the start point for new

recording. Pressing “F” forwards

the tape and pressing “R” reverses

it.

3) Press Recording Start/Stop Button

to start recording.

NOTE:

Noise may appear during Retake.

This is normal.

FEATURE: Picture Stabilizer

PURPOSE: To compensate for unstable images

caused by camera-shake, particularly

at high magnification.

OPERATION: 1) Press P. STABILIZER. “

”appears.

n To switch off the Picture

Stabilizer, press P. STABILIZER.

The indicator disappears.

NOTES: ●

Accurate stabilization may not be

possible if hand shake is excessive,

or under the following conditions:

•

When shooting subjects with

vertical or horizontal stripes.

•

When shooting dark or dim

subjects.

•

When shooting subjects with

excessive backlighting.

•

When shooting scenes with

movement in various directions.

•

When shooting scenes with low-

contrast backgrounds.

●

Switch off the Picture Stabilizer

when recording with the

camcorder on a tripod.

P. STABILIZER

RETAKE (R/F)

20 EN

RECORDING

Basic Features (cont.)

Auto Date Record mode

Date display

Time display

Date/Time display

Date-off mode (No display)

PM10:50:00

Date display

Time display

Date/Time display

DEC 25.98

PM10:50:00

Auto date record mode

Auto date record

executed

DEC 25.98

AUTO DATE

Auto Date Record mode

DATE/TIME

FEATURE: Date/Time Insert

PURPOSE: To display the date and time in the

viewfinder or on a connected color

monitor, as well as to record them

manually or automatically.

OPERATION: 1) Turn the Select Dial to any

position except AUTO LOCK.

2) Choose a display mode by

pressing DATE/TIME repeatedly

while in Record-Standby to cycle

through the modes as shown in the

illustration at left.

n You should have already

performed the Date/Time Setting

procedure (Z pg. 11). If you

haven’t, do so first.

NOTES:

DISPLAY

●

The selected display can be

recorded.

●

If you don’t want to record the

display, select the Date-off mode

before shooting.

●

If you want to delete the display

during shooting, press DATE/TIME.

●

To recall the display, engage the

Record-Standby mode and press

DATE/TIME repeatedly until the

desired display appears.

AUTO DATE RECORD

●

Your camcorder automatically

records the date for about 5

seconds after recording is initiated

in the following situations:

•

After changing the date.

•

After loading a cassette.

•

After Auto Date Record mode is

selected by pressing DATE/TIME.

In this mode, the date is replaced

after 5 seconds with “AUTO DATE”

but this is not recorded.

●

Setting the Select Dial to AUTO

LOCK always engages the Auto

Date Record mode, and disables

all other modes.

Select Dial

Display

Page is loading ...

JVC GR-AX930U User manual

This manual is also suitable for

JVC GR-AX930U User manual

Related papers

Other documents