Directed Electronics 24923 User manual

2244992233

➤

OOwwnneerr’’ss//IInnssttaallllaattiioonn GGuuiiddee

i

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy

Directed Electronics, Inc. (hereinafter "Directed") promises to the original purchaser to

repair or replace with a comparable reconditioned Directed DIY remote start unit if this

Directed DIY remote start unit (hereinafter "Unit"), excluding without limitation, any

remote transmitters or associated accessories, proves defective in materials or workman-

ship under normal use for the life of the vehicle which the Unit is originally installed.

During this period, so long as the Unit remained installed in the original vehicle, Directed

will at its option, repair or replace this Unit if it is proved defective in workmanship or

material PROVIDED the Unit is returned to Directed's warranty department at One

Viper Way, Vista, CA 92081, along with $20 postage and handling fee, a bill of sale or

other dated proof of purchase bearing the following information: Date of purchase, name

and location of the merchant who sold the Unit, and product description. This warranty

does not cover labor costs for the removal or reinstallation of the Unit. This warranty is

non-transferable and does not apply to any Unit that has been modified or used in a man-

ner contrary to its intended purpose, and this warranty does not cover damage to any Unit

caused by installation or removal of the Unit. This warranty is void if the Unit has been

damaged by accident or unreasonable use, neglect, improper service or other causes not

arising out of defects in materials or workmanship. Directed makes no warranty against

theft of a vehicle or its contents.

THE FOREGOING WARRANTY IS THE EXCLUSIVE PRODUCT WARRANTY,

OTHERWISE, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO

EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MER-

CHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY

EXCLUDED AND DISCLAIMED TO THE MAXIMUM EXTENT ALLOWED BY

LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON

TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF

THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY

AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-

ERS OR INSTALLERS. SOME STATES DO NOT ALLOW THE LIMITATION ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION

MAY NOT APPLY TO YOU.

LIMITATION OF DAMAGES AND LIABILITY. CONSUMER'S REMEDY IS LIM-

ITED TO REPAIR OR REPLACEMENT OF THE UNIT, AND IN NO EVENT

SHALL DIRECTED'S LIABILITY EXCEED THE PURCHASE PRICE OF THE

UNIT. IN ANY EVENT, DIRECTED SHALL NOT BE LIABLE FOR ANY DAM-

AGES INCLUDING, BUT NOT LIMITED TO, ANY DIRECT, INDIRECT, INCI-

DENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, LOST

PROFITS, LOST SAVINGS, OR, TO THE EXTENT ALLOWED BY APPLICABLE

LAW, DAMAGES RESULTING FROM DEATH OR INJURY ARISING OUT OF

ii

OR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, OR

INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO

NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION

MAY NOT APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT

ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE

RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO

COUNTY, CALIFORNIA.

IIMMPPOORRTTAANNTT NNOOTTEE::

This product warranty is automatically void if its date code or serial number is defaced,

missing, or altered.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

➤ Date of purchase

➤ Authorized dealer's company name and address

➤ Item number

1

ttaabbllee ooff ccoonntteennttss

lliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ii

wwhhaatt iiss iinncclluuddeedd.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

iinnssttaallllaattiioonn ttoooollss.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 33

iimmppoorrttaanntt iinnffoorrmmaattiioonn .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 44

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

wwaarrnniinngg!

! ssaaffeettyy ffiirrsstt .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 55

mmaaiinn hhaarrnneessss ((HH11)),, 88--ppiinn ccoonnnneeccttoorr .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. 88

sseeccoonnddaarryy hhaarrnneessss ((HH22)),, 77--ppiinn ccoonnnneeccttoorr.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 99

rreellaayy hheeaavvyy ggaauuggee wwiirreess .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 99

uussiinngg LLEEDD tteesstt pprroobbee .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1100

iinnssttaallllaattiioonn .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 1111

wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddee .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. 1122

step 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

step 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

step 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

step 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

step 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

step 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

step 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

step 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

step 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

step 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

rreemmoottee ffuunnccttiioonnss .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4488

standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

ccoonnttrrooll mmoodduullee pprrooggrraammmmiinngg .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5500

uussiinngg yyoouurr ssyysstteemm .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5533

warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

locking with remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

unlocking with remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

ignition-controlled door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

remote start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

timer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

ppiitt ssttoopp

mmooddee.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. 5588

ttrruunnkk//aauuxxiilliiaarryy .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5599

ccooddee hhooppppiinngg ®® rree--ssyynncchhrroonniizzee .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5599

ttrroouubblleesshhoooottiinngg .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 6600

gglloossssaarryy ooff tteerrmmss ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 6622

nnootteess .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 6633

qquuiicckk rreeffeerreennccee gguuiiddee:: .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .

. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 6655

2

3

wwhhaatt iiss iinncclluuddeedd

➤ Control Module

➤ One 4-Button Remote

➤ 8-Pin Main H1 Harness

➤ 7-Pin H2 Secondary Harness

➤ 6-Pin Relay Heavy Gauge Wires

➤ Shutdown Toggle Safety Switch

➤ Hood Pin Switch

➤ Installation Kit

➤ Razor Knife

➤ CDROM—Do-It-Yourself Installation Video

Additional parts may be required (such as relays or bypass).

iinnssttaallllaattiioonn ttoooollss

➤ Digital Multi-Meter

➤ Drill

➤

1

/

4 Drill Bit (for hood

pin switch)

➤ Screwdrivers

(Phillips and Flathead)

➤ Wire Stripper

➤ Solder Iron

➤ Electrical Tape

➤ Pliers

➤ Crimping Tool

note: The installation tools listed above may be optional

and those required will vary depending on your vehicle.

4

iimmppoorrttaanntt iinnffoorrmmaattiioonn

Congratulations on the purchase of your remote start keyless

entry system. This system will allow convenient access to your

vehicle with the push of a button, as well as remote start and

other optional features. Properly installed, this system will

provide years of trouble-free operation.

Please take the time to carefully read this User’s Guide in its

entirety and watch the Do-It-Yourself Installation Video

(CDROM) prior to installing your system.

You can print additional or replacement copies of this manual by

accessing the Directed web site at www.designtech-intl.com.

system maintenance

The system requires no specific maintenance. Your transmitter is

powered by a miniature 3-volt battery (type CR2032) that will

last approximately one year under normal use. When the battery

begins to weaken, the operating range will be reduced.

➜

important! If you are not comfortable working with elec-

tronics or unfamiliar with the tools required, please con-

tact your local dealer for advice or ask to have the remote

start professionally installed to avoid costly damages.

Failure to properly install the remote starter may result in

property damage, personal injury, or both.

5

fcc/id notice

This device complies with Part 15 of FCC rules. Operation is

subject to the following conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

wwaarrnniinngg!! ssaaffeettyy ffiirrsstt

The following safety warnings must be observed at all times:

➤ When properly installed, this system can start the vehicle via

a command signal from the remote control transmitter.

Therefore, never operate the system in an area that does not

have adequate ventilation. The following precautions are the

sole responsibility of the user; however, the following recom-

mendations should be made to all users of this system:

1. Never operate the system in an enclosed or partially

enclosed area without ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed area

or when having the vehicle serviced, the remote start

system must be disabled using the toggle switch.

3. It is the user's sole responsibility to properly handle and

keep out of reach from children all remote control units

➜

6

to assure that the system does not unintentionally

remote start the vehicle.

4. THE USER MUST INSTALL A CARBON

MONOXIDE DETECTOR IN OR ABOUT THE

LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT

LIVING AREAS TO THE ENCLOSED OR

PARTIALLY ENCLOSED VEHICLE STORAGE

AREA MUST AT ALL TIMES REMAIN CLOSED.

➤ Use of this product in a manner contrary to its intended mode

of operation may result in property damage, personal injury,

or death. Except when performing the Safety Check outlined

in this user’s guide, (1) Never remotely start the vehicle with

the vehicle in gear, and (2) Never remotely start the vehicle

with the keys in the ignition. The user will be responsible for

having the neutral safety feature of the vehicle periodically

checked, wherein the vehicle must not remotely start while

the car is in gear. This testing should be performed by an

authorized Directed dealer in accordance with the Safety

Check outlined in this product installation guide. If the

vehicle starts in gear, cease remote start operation immediately

and consult with the Dealer to fix the problem immediately.

➤ After the remote start module has been installed, test the

remote start module in accordance with the Safety Check

outlined in this installation guide. If the vehicle starts when

performing the Neutral Safety Shutdown Circuit test, the

7

remote start unit has not been properly installed. The remote

start module must be removed or properly reinstalled so that

the vehicle does not start in gear. OPERATION OF THE

REMOTE START MODULE IF THE VEHICLE STARTS

IN GEAR IS CONTRARY TO ITS INTENDED MODE

OF OPERATION. OPERATING THE REMOTE START

SYSTEM UNDER THESE CONDITIONS MAY

RESULT IN PROPERTY DAMAGE OR PERSONAL

INJURY. IMMEDIATELY CEASE THE USE OF THE

UNIT AND REPAIR OR DISCONNECT THE

INSTALLED REMOTE START MODULE. DIRECTED

WILL NOT BE HELD RESPONSIBLE OR PAY FOR

INSTALLATION OR REINSTALLATION COSTS.

8

mmaaiinn hhaarrnneessss ((HH11)),,

88--ppiinn ccoonnnneeccttoorr

___

Use the following wiring guidelines for the H1 harness.

PPiinn ## WWiirree CCoolloorr NNoottee

H1/1 Blue Required when using a bypass module or a

(-) 3

rd

ignition output.

H1/3 Brown This wire

mmuusstt

be connected.

H1/7

Lt. Green/

Black

Use if the vehicle is equipped with a factory

alarm disarm or for retained accessory power

cancellation (RAP).

WHITE (+/- selectable) Parking Light Flash Output (optional)

LT. GREEN/BLACK Factory Alarm Disarm/RAP Cancellation

WHITE/BLUE (-) Remote Start Activation Input

BLACK Ground

GRAY (-) Hood Pin Shutdown Input

BROWN (+) Brake Switch Shutdown Input

VIOLET/WHITE Tachometer Input (optional)

BLUE (-) 200mA Status Output

HH11//11

HH11//22

HH11//33

HH11//44

HH11//55

HH11//66

HH11//77

HH11//88

9

sseeccoonnddaarryy hhaarrnneessss ((HH22)),,

77--ppiinn ccoonnnneeccttoorr

___

rreellaayy hheeaavvyy ggaauuggee wwiirreess

___

PINK/WHITE (+) Output for 2

nd

Ignition

(not programmable)

RED (+) (30A) High Current 12V Input

PINK (+) (30A) Output to Ignition Circuit

ORANGE (+) (30A) Output to Accessory Circuit

RED (+) (30A) High Current 12V Input

VIOLET (+) (30A) Output to Starter Circuit

11

22

33

44

55

66

VIOLET Unlock #87A Normally Open (Input) looped back

to H2/4

BLUE/BLACK Unlock #30 Common Output

BROWN/BLACK UnLock #87 Normally Closed

VIOLET/BLACK Lock #87A Normally Open (Input) 15 A

GREEN/BLACK Lock #30 Common Output

WHITE/BLACK Lock #87A Normally Closed

RED/WHITE (-) Channel 2 (auxiliary channel ie: trunk)

HH22//11

HH22//22

HH22//33

HH22//44

HH22//55

HH22//66

HH22//77

10

uussiinngg LLEEDD tteesstt pprroobbee

To use the LED test probe:

1. Remove the protective cover off the probe tip. Save the

protective cover for reinstallation on the probe tip when

the LED tester is not being used.

2. Connect the Black clip to a good chassis ground.

3. Connect the Red clip to a good +12V source. Both the

Red and Green LEDs should be illuminated dimly.

4. If a positive voltage source is probed, the Red LED will

illuminate brightly, and the Green LED will extinguish.

5. If a negative source is probed the Green LED will illu-

minate brightly and the Red LED will extinguish.

Alternate procedure to use the LED test probe (only for use on

probing positive voltage wires):

1. Remove the protective cover off the probe tip. Save the

protective cover for reinstallation on the probe tip when

the LED tester is not being used.

2. Connect the Black clip to a good chassis ground.

3. If a positive voltage source is probed, the Red LED will

illuminate brightly.

note: Do not use this test probe on computerized equip-

ment or on the tachometer wiring as damage can result.

11

iinnssttaallllaattiioonn

Be sure to read this section thoroughly and view the Do-It-

Yourself Installation CDROM video in its entirety before

starting the installation. Pay special attention to all warnings to

prevent personal injury or damage to your vehicle.

Visit our 24-hour technical Web site (

wwwwww..ddeessiiggnntteecchh--iinnttll..ccoomm

)

to get a vehicle-specific wiring guide prior to starting this instal-

lation. Have on hand your crash code number when contacting

tech support or visiting the web site. During the installation if

you are unable to answer your questions on the Web site, call

11--

880000--447777--11338822

(to get hours of phone operation) for live tech-

nical assistance.

warning! Verify that the vehicle is set to

park and that the parking brake is set

before beginning installation.

warning! On vehicles with air bags or sup-

plemental restraint systems (SRS) you may

notice a bright yellow tube with small wires

in it marked SRS underneath the steering

column near the key cylinder. DO NOT

tamper or unplug these for any reason to

prevent costly damages to your vehicle or

personal injury. Tampering may cause

unintended deployment of airbags.

warning! This system is intended for auto-

matic, fuel-injected vehicles only. Installation

in any other vehicle is contrary to its intend-

ed use.

12

wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddee

VIOLET/BLACK - Lock #87 Normally Open Input 15A Fused

BROWN/BLACK - Lock #87A Normally Closed

BLUE/BLACK - Unlock #30 Common (Output)

VIOLET - Lock #87 Normally Open Input (looped to VIOLET/BLACK)

GREEN/BLACK - Lock #30 Common (Output)

WHITE/BLACK - Lock #87 Normally Closed

RED/WHITE - (-) Channel 2

H1

H2

Heavy Gauge

Wires

RED - IGNITION CONTROL

GREEN - DOOR UNLOCK

WHITE - DOOR LOCK

13

step 1

Ground Wire

The BLACK (H1/5) wire on the main 8-pin harness is ground.

First strip back a ¾-inch section of the insulation off the BLACK

wire and crimp a ring terminal (not provided) to that wire.

Locate a clean, paint-free metal surface in the drivers kick panel.

Using a self-tapping screw, drill the screw with the ring terminal

to the metal area. Once screwed down, pull on the wire to ensure

a good connection.

SELF-TAPPING

BOLT OR SCREW

RING

TERMINAL

GROUND

WIRE

NOTE: REMOVE ANY PAINT

BELOW RING CONNECTOR

DIA-591

note: More problems are attributed to poor ground con-

nections than any other cause. Take extra care to ensure

the ground is a clean metal-to-metal contact and secure.

➜

14

step 2

Constant Power and Ignition wires

Almost all power and ignition wires can be found behind the key

cylinder under the lower drivers side dash panel. Using the

appropriate hand tools, remove the lower dash panel using care

not to break any parts. If the panel does not come off easily

check for any additional screws you may have missed.

Once the lower dash panel has been removed, locate the ignition

harness at the back of the key cylinder. This is usually a group of

thicker wires. With the ignition harness exposed, use your LED

tester to find your power and ignition wires.

Place the black lead of the test probe to a clean metal surface in

warning! On vehicles with air bags or sup-

plemental restraint systems (SRS) you may

notice a bright yellow tube with small wires

in it marked SRS underneath the steering

column near the key cylinder. DO NOT

tamper or unplug these for any reason to

prevent costly damages to your vehicle or

personal injury. Tampering may cause

unintended deployment of airbags.

➜

15

the kick panel area and secure it. Probe one of the thicker gauge

wires. The color and identity of your specific vehicle wiring can

be obtained at www.designtech-intl.com. With the key in the off

position, test the suspect wire. The constant power wire will illu-

minate the Red LED on the test probe.

Once the constant power wire has been identified, solder the two

heavy gauge RED wires from the control module (relay heavy

gauge) to it and wrap the connection with electrical tape.

With the test probe black lead still in the kick panel, locate the

ignition wire in the same location. It will test differently than

note: If the vehicle has two constant power wires, utilize

both constant power wires. Connect one of the heavy

gauge RED wires to one of the constant power wires and

the other heavy gauge RED wire to the other constant

power wire.

Control

Module

30 A

fuses

RED heavy

gauge wires

warning! Before making any connection

to constant battery power make sure that

the two green 30 amp fuses are removed

from the fuse holders on the two thick red

wires (heavy gauge wires). Failure to do so

may cause fire or shorting of sensitive elec-

trical components.

16

constant (+)12 volts. Locate the suspected wire using the

www.designtech-intl.com Web site and place the red lead of the

test probe on the suspected wire. With the key in the off position

the probes LED will be off. Turn the key to the on position and

the LED tester will illuminate Red. Now watching your probe,

turn the key to the crank position. If the LED extinguishes this

is not an ignition wire but an accessory wire. If the wire tests

correctly, solder the thick PINK (4) wire of the heavy gauge wires

to it and wrap the connection with electrical tape.

If the vehicle requires more than one ignition as per the Web site

information follow the same test procedure and solder the thick

PINK/WHITE (6) wire of the heavy gauge wires to it and wrap

the connection with electrical tape. If your vehicle has only 1

ignition source, secure the PINK/WHITE out of the way.

If your vehicle requires more than two ignitions, an additional

relay (not provided) is required. Refer to the diagram below.

Page is loading ...

Directed Electronics 24923 User manual

This manual is also suitable for

Directed Electronics 24923 User manual

Related papers

Other documents