Page is loading ...
Usage
La hotte JDA 3830 est équipée de deux
moteurs.
La puissance du moteur est réglable au
moyen d’un variateur électronique.
La hotte est équipée d’une vitesse maximum
(intensive).
L’intensive ne doit être utilisé qu’en présence
d’une concentration de vapeurs particulière.
Dans les autres cas, utiliser les vitesses
pouvant être sélectionnées au moyen du
variateur électronique.
Nous vous recommandons de mettre
l’appareil en marche avant de procéder à la
cuisson d’un plat quelconque et de laisser
fonctionner l’appareil pendant: 10 minutes
encore après la cuisson, jusqu’à ce que
toute odeur ait disparu.
Le tableau de bord dispose de deux
interrupteurs, un pour le réglage continu du
moteur ( Interrupteur de gauche) et un autre
pour l’éclairage du plan de travail
(Interrupteur de droite).
Entretien
Débrancher l’appareil du réseau électrique
avant de procéder à toute opération d
entretien.
Filtre à graisse
La hotte est munie d’un filtre à graisse
métallique.
Pour nettoyer le filtre, procéder comme suit:
— Appuyer en même temps sur les deux
boutons Q vers le haut et les déplacer
ensuite vers l'intérieur (fig. 6).
La grille et le filtre constituent un seul
bloc.
0
0
1
Allumage et variation
électronique de la vitesse
du moteur
Vitesse intensive
Touche
éclairage
— En cas d’utilisation normale, le filtre à
graisse doit être lavé une fois par mois au
lave-vaisselle ou bien avec un peu de
savon dissout dans de l’eau tiède; bien
laisser sécher le filtre avant de le remonter.
Filtre au charbon actif
Ce filtre élimine les odeurs et les vapeurs qui
se forment pendant la cuisson.
En conditions d’usage normal, il faut le
remplacer tous les 6-8 mois.
Pour le commander, s’adresser au
fournisseur Ne jamais le laver.
Pour le démontage, procéder de la façon
suivante:
— Appuyer sur les deux touches C (fig. 2),
tirer légèrement le filtre vers l’avant et
l’enlever.
Attention
Le non respect des normes d’entretien de
l’appareiI et de remplacement et nettoyage
des filtres comporte des risques d’incendie.
Nous recommandons donc vivement de
respecter ces instructions.
Remplacement des lampes
— Débrancher l’appareil du réseau
électrique.
— Enlever le hublot R en actionnant
simultanément les deux stops S (fig. 6)
jusqu'à ce que ce dernier ne se dégage
complètement des crochets auxquels il
est suspendu (fig. 7).
— Remplacer la lampe grillée en utilisant
exclusivement une lampe néon de 14W
(Fig. 7).
— Si l’on désire faire appel au Service Après
Vente car l’éclairage ne fonctionne pas,
contrôler avant tout si les lampes sont
bien inserées.
Nettoyage
Pour le nettoyage extérieur de la hotte,
utiliser un chiffon imbibé d’alcool ou des
détergents liquides neutres. Eviter l’usage
de tout produit abrasif.
Cet appareil est conforme aux normes
87/308 EWG concernant les antiparasites.
View of the hood
1) Motor speed switch
2) Light switch
3) Extractable drawer
4) Metal grease filter
5) Cooking surface lighting
Using the hood
The hood may be used in 2 ways:
— external exhausting version
— internal recycle version
External exhausting model
The air is expelled outside by means of
pipes to be connected to the coupling
flange A (fig 1).
Choosing the exhausting pipe
The coupling ring A has a diameter of 120mm.
We suggest to use Ø 120 mm exhausting
pipe.
Using the multi-connector Ø100, Ø110 and
Ø125 mm exhausting pipes can be used.
Ø 120 mm exhausting pipe
: the multi-
connector B has not to be fitted.
Ø 125 mm exhausting pipe
: insert the
multi-connector B on the coupling ring A and
remove, using a proper tool, the upper
unused Ø 100 and Ø 110 mm rings of the
multi-connector B.
Ø 110 mm exhausting pipe
: same
procedure, but removing the Ø 100 mm ring
only.
Ø 100 mm exhausting pipe
: apply the
multi-connector B on the coupling ring A.
GB
Recycling version (filtering)
The air is purified by means of a carbon filter
and then returned to the room.
The active carbon filter can be ordered from
the supplier.
To install the filter, proceed as follow:
fit the filter into its seat and fix with the two
hooks C (fig. 2).
The filtered air is discharged above the top
cabinet.
The baffle plate D (fig. 1) can be fitted to the
outlet hole using the screws supplied.
Installation
The hood must be installed at least 42 cm
from the hob of electric cookers and at least
65 cm from the hob in the case of gas or
mixed cookers.
Warning!
— If the hood is run at the same time as a
burner or fireplace that depend on ambient
air (for example gas, Diesel, coal or wood
heaters, water heaters, etc.) be careful,
because the hood, when it exhausts the
air, removes the ambient air required by
the burner or fireplace for combustion.
— For secure operation and to prevent
discharged gas from coming back in, the
vacuum must not exceed 0,04 mbr.
This may be done by making sure the air
inlet into the room passes through non-
closing openings such as air recycling
wall boxes, doors, windows or with other
technical measures.
— No food must be cooked flambé
underneath the hood.
The use of an unprotected flame is
dangerous for the filters and could cause
fires.
Therefore, never use an open flame under
the hood. When frying foods, never leave
the pan alone because the cooking oil
could flare up.
— The hood must not be connected to fuel
exhaust flues (boilers, heating systems,
water heaters, etc.).
— Please, keep to the provisions of official
directives regarding the question of fume
discharge.
14
15
0
0
1
Intensive speed
Light switch
Electronic speed switch
— The manufacturers refuse to accept any
responsibility for damage to the hood or
its catching on fire because of failure to
observe the above instructions.
Suggestions for the installation and
use of the hood
— The horizontal sections of the pipe must
be slanted slightly upwards (about 10%)
to ensure an easy flow of the air outwards.
— The best performance of the unit is
obtained in the external exhaust model
(suction), therefore in the limits of the
possibilities it is advised to use the external
exhaust (suction) type.
— The best performances are obtained with
short pipes (max. 4 m) and with few
curves.
Electric connection
Before completing any connection, make
sure the house voltage corresponds with the
voltage indicated on the label affixed inside
the hood.
The hood is supplied with a standard plug;
connect it to a correspondingly standard
socket. In the case is intended to connect the
appliance permanently to the mains after
having removed the plug supplied, must be
fitted a two-pole switch conforming to
regulations with an opening distance
between contacts of not less than 3mm
The manufacturers are not liable for any
problems caused by the user’s failure to
observe the above instructions.
Fixing the hood
Apply the scheme supplied (Nº 49) on the
right of the cabinet so that the lines marked
by the arrows match the cabinet ensuring
that they meet at the back and under.
Make two Ø 2 mm holes at points 1 and
2 (fig. 3).
Carry out the same operation on the left.
Fix the hood to the cabinet using screws E
(4,5x16) supplied with the appliance (fig. 3).
Use the shim F supplied with the hood for 16
mm cupboard side panels.
Fit the shim F to the left and to the right of the
fixing curves of the hood and hook them in
the holes.
Adjusting the removable drawer
The hood may be mounted in cabinets with
different depths.
The back of the drawer can be adjusted so
that the front of the removable drawer is the
same depth as the cabinet.
Proceed as follows:
— Unscrew the screws G, move the square
plates H as required and tighten the screw
G (fig. 4).
Replacing the plastic front
The hood is supplied with a brown plastic
front which can replace the white one already
mounted.
To mount the brown plastic front proceed as
follows:
— Completely open the removable drawer L
(fig. 1).
— Remove the two grease filters.
— remove the shaped metal piece M by
unscrewing the two fixing screws N
(fig. 5).
— Remove the three screws O which fix the
band P from the inside of the removable
drawer.
— Fit the brown plastic front to the drawer
with the same three screws O.
— Refit the shaped metal piece M and the
grease filters.
Using Instructions
The hood model JDA 3830 is fitted with two
motors.
The speed of the motors is adjusted by
means of a continuous sliding switch.
The hood is provided with an intensive
speed.
Use the intensive speed switch only in case
of high concentration of vapour.
The hood should be switched ON several
minutes before you start cooking and should
be allowed to run until all the vapours have
been eliminated.
The switching plate is fitted with two switches
one for continuous adjustment of the
ventilator (left switch) and one for illuminating
the work surface (right switch).
Maintenance
Before performing any maintenance
operation, disconnect the hood from the
electricity.
Metal grease filter
Wash the filter, in a dishwasher or with
detergent and water, periodically according
to how often the appliance is used, but at
least once every 4 weeks.
Before refitting the filter ensure that it is
perfectly dry.
To remove this filter push simultaneously
the two handle Q first upwards then inwards
(fig. 6).
Grill and metal filter are a unique indivisible
component and they cannot be divided, to
avoid any damage to it.
Active Carbon Filter
This filter eliminates the odours and vapours
which form during cooking.
When used in normal conditions it should be
replaced at intervals of 6-8 months.
These filter can be ordered from the supplier
The carbon filter cannot be washed or
regenerated.
To dismount,the filter proceed as follows:
Press the two buttons C (fig. 2), pull the filter
slightly forwards and remove it.
Important
Failure to observe the rules for cleaning the
appliance and changing and cleaning the
filters may cause fires. Therefore, we
recommend observing these instructions.
Replacing the lamps
— Disconnect the hood from the electricity.
— Remove the lamp cover R by pushing
simultaneously two unlocking button S
(Fig. 6) 'till having it completely removed
(fig. 7).
— Always replace burnt-out lamps with neon-
lamp 14 Watt max. (Fig. 7).
— Re-close the grate or the lamp cover.
— Before calling for Repair Service because
the hood fails to light up, make sure the
neon lamp is well-inserted.
Cleaning
To clean the outside of the hood use a cloth
moistened with denatured alcohol or neutral
liquid detergents. Never use products
containing abrasive.
This appliance meets 87/308 EWG radio
and television noise standards.
16 17
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Juno JDA3830E Manuale utente
- français: Juno JDA3830E Manuel utilisateur
Related papers
Other documents
-
ROSIERES RHV 911 Owner's manual
-
Electrolux EFC639X User manual
-
Smeg KSET900 User manual
-
-
Turboair LIPARI IX/LX/A User guide
-
-
Whirlpool HP 90 F User guide
-
ELICA ELIPLANE LX IX F/60 User manual
-
Aeg-Electrolux DF6261B/CH User manual
-