VENTILATORE A TORRE
TOWER FAN
TURMVENTILATOR
VENTILATEUR À COLONNE
VENTILADOR DE TORRE
RoHS
MANUALE D'ISTRUZIONI - INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG - LIVRET D'INSTRUCTIONS
MANUAL DE INSTRUCCIONES
OI 11
VIVALDI
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
a
b
c
a. FRONT
1. LCD
2. SPEAKER
3. PERFUME COVER
4. FAN EXHAUSTED GRILL
5. FRONT COVER
6. HEATER EXHAUSTED GRILL
7. BASE GLASS
b. SIDE
8. SD or USB or AUX IN PORT
c. REAR
9. REMOTE CONTROLLER
10. HANDLE
11. REAR HOUSING
12. POWER SWITCH
-FAN/HEATER SELECT
13. PLUG
On/Off
Mode Timer setting
Oscillation
Temp/
Clock/
Volume
Decrease
Temp/
Clock/
Volume
Increase
Music On/Off
a = loose
b = tight
a
b
2
3
Remove the product carefully from the plastic bag and the carton. Follow step 1 to 3 to fix base.
Put the heater on a stable flat surface. Set the main power foot switch to’ OFF’. Plug the
cord set into a 220-240V~A.C. electrical outlet.
1
ASSEMBLING
4
=ON
=OFF
9
GENERAL DIRECTIONS
1. Remove the packaging and make sure that the appliance is intact. If in doubt, do not use it
and contact our Technical Assistance Centre. Packaging materials (plastic bags, polystyrene,
staples etc.) must be kept out of the reach of children as they could be hazardous.
Caution:
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
2. Before connecting the appliance, check that the appliance rating corresponds to the mains
rating.
If the power cord is damaged, it must be replaced by the manufacturer or his service agent or a
similar qualified person in order to avoid a hazard.
3. This appliance must only be used for the purpose for which it has been manufactured, i.e. as
a tower fan. The manufacturer is not responsible for any damage caused by improper or
incorrect use.
4. Before cleaning or carrying out maintenance on the appliance, disconnect it from the
electrical mains by removing the plug from the electrical outlet or by switching off the system
switch.
5. If the appliance is faulty and/or operating incorrectly, switch it off without tampering with it. If
the above is disregarded, the safety of the appliance may be compromised.
6. Switch off the appliance and remove the plug from the electrical outlet when not in use.
7. The use of any electrical appliance calls for the awareness of some basic rules, such as:
- do not use the appliance near sources of water such as baths, showers or swimming pools
- do not touch the appliance with wet or damp hands or feet
- do not leave the appliance exposed to atmospheric agents
- the heater must not be located immediately below a socket- outlet
- in order to avoid overheating, do not cover the heater
8.The unit has an acoustic warning device that is triggered in the event of overheating during
the "heating" function. If it goes off, turn off the appliance immediately. IMPORTANT:
when the alarm sounds, do NOT use the appliance.
9. Max. ambient temperature 35°C.
10. Do not use the appliance in the presence of potentially flammable or explosive liquids or
gases.
11. In order to avoid overheating, do not cover the heater.
ENGLISH
=HEATER
=FAN
09
10
CURRENT TIME SETTING
1h
6h
12h
18h
24h
Press the “ ” timer button
for 3 seconds, the hour digit
start to flash
1 2
Press “+” or “-” button set the
current hour
3
Press the “ ” timer button
to confirm the hour selected,
and the minute digit start
to flash
4
Press “+” or “-” button set the
current minute, press “ ”
timer to confirm selected
1h
6h
12h
18h
24h
1h
6h
12h
18h
24h 1h
6h
12h
18h
24h
TIMER SETTING
1h
6h
12h
18h
24h
empty dot: off ( canceled) status
selected dot: working ( confirmed) status
flash dot: selected ( waiting confirmation) if without any
timer operations, flashing carry out 10 seconds
1h
6h
12h
18h
24h
Segments hours are 24:
corresponding to 24 hours
of the day
5s
1
Low speed
High speed
Nature wind
Sleeping wind
Mid speed
Cool fan
Low heat
Hight heat
Auto
2 3
Press the “ I ” button
turn on power and
turn the other switch
to the “ ”
Press the “MODE” button
can set speed option:
low medium maximum
natural wind sleeping wind
5s
1
2 3
Press the “ I ” button
turn on power and
turn the other switch
to the “ ”
Press the “ ” power button
the temperature and the
current time display for 5
seconds alternately, “ ”
high heat will be activated.
Press the “ Mode” button
can set heater option:
Auto cool fan low heat
high heat
When chose “AUTO”mode, the temperature will flash and a target temperature can be
set by pressing “+”or “-”button, the target temperature can be from 10
℃ to 35℃. When
the environment temperature lower than the target temperature, the heater start to work.
HEATER MODE
FAN MODE
flash for 5 seconds
and confirm selected
Press the “ ” power button,
the temperature and the
current time display for 5
seconds alternately,“ ” low
speed will be activated.
11
12
1h
6h
12h
18h
24h
Pressing the “ ” timer button, one dot will flash
1h
6h
12h
18h
24h
2
1h
6h
12h
18h
24h
3
1
1h
6h
12h
18h
24h
Press “+” or “-” button can move dot for time selection
Press “ ” timer button to confirm the selected time, dot
become “ ” then the next dot will become flashing, after
10 seconds the dot flashing stops and the timer setting
is completed
If you want to cancel the timer setting ,press “ ” button, and
use “+” or “-” button to move flash dot, when the “ ” become “ ”,
press the “ ” button to cancel the selected time and dot will be “ ”
If you want to set the continuous working time, repeat pressing “ ”
button, the “ ” will become “ ” one by one, then next dot will
flash for 10 seconds
13
14
OSCILLATING
1h
6h
12h
18h
24h
Press the “ ” oscillation button will allow the Heater to oscillate. To stop the oscillation,
press the “ ” oscillation button once more.
1h
6h
12h
18h
24h
open
close
PERFUME FUNCTION
There is a perfume slot on the right of speaker. Drop some perfume to the ceramic and
insert to the slot and close the cover.
(Important: Must use water-based fragrance, can not use oil-based fragrance)
1
Use a coin to open the
cover as picture 1 show
Take out the ceramic
and drop the water-based
fragrance
Use a coin and close the
cover as picture 3 show
3
2
21
REMOTE CONTROL
1. lnstall two “AAA” batteries.
2. The Remote Control button is labeled as below.
SAFETY FEATURES
1. A thermal overload protector is built in to prevent overheating.
2. When an overheat temperature is reached, the Heater will be automatically shut off. Once
unit cool down, can be re-booted by user.
3. If the unit is tilted, a safety system automatically will cut off the power, after resume it to
vertical position , it does not operate, it only can operate again by pressing on/off switch on the
top of body
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING, DO NOT
IMMERSE APPLIANCE IN WATER!
CLEANING: IMPORTANT! DO NOT IMMERSE APPLIANCE IN WATER!
Clean the Air Inlet with the vacuum brush attachment on your Vacuum cleaner,
Clean the body of the Appliance with a soft Cloth.
CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc. as they will damage the
Appliance. NEVER use ALCOHOL OR SOLVENTS.
STORAGE: Store the Appliance with these instructions in the original in a cool, dry place.
ATTENTION
The symbol on the product means that at the end of its life, the appliance must not be
considered normal waste but hazardous waste and, as such, must be disposed of in specific
recovery and disposal areas, as prescribed by the EC Directive 2002/96/EC (WEEE). By
disposing of this product correctly, you can prevent negative consequences for the environment
and for human health, due to the presence of potentially hazardous substances in the product.
For more detailed information about recycling this product, contact the local authorities, the local
waste disposal service or the shop from which the product was purchased. Unlawful disposal
will be punished according to the law.
1
2
SD
AUX In
USB
Music Play
Mp3 bracket assembly
Music Play operation
1h
6h
12h
18h
24h
Compression format: MP1/MP2/MP3
MP3 bit rates: 8-320 kbps and VBR (= Variable BitRate)
MP3 sample rates: 16, 32, 44.1, 48, 11.025, 22.050, 24, 8 kHz
Supported Number of Files/Folders: File: Max. 1000 Folder: Max. 1000 (including File)
Do not use “ ” button to close music directly, If you do that, the music will
continue automatically after few minutes, reminding you that the music is
not closed yet. To stop the music please touch the “ ” button.
1
2
3
1h
6h
12h
18h
24h
1h
6h
12h
18h
24h
Insert a SD card,mp3 player
or a U disk to corresponding
port on right of the unit,and
press the “ ” button , will start
to play music.
15
16
Press the “ ”button to close
music
USB/SD port - Music play
Press the “ + ” or “ - ” button to
increase or decrease the volume.
AUX input - Music play
Use Mp3 player to adjust the volume
USB/SD port - Music play
You can use the button
" " or " " of remote
control to play previous or
next track of music.
AUX input - Music play
Use Mp3 player control to
play previous or next track
of music
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
