ANSMANN ALCT 6-24/1 Operating instructions

ANSMANN
Brand
ANSMANN
Model
ALCT 6-24/1
Category
Battery chargers
Type
Operating instructions

This manual is also suitable for

Page is loading ...


Automatic charger for lead acid-/sealed lead acid batteries 6 V;12 V; 24 V.

> For automatic charging of all types of lead acid batteries and sealed lead acid batteries with
output voltage 6 V; 12 V; 24 V
> Protection against short circuit and wrong polarity
> Protection against overcharging
> Charging with IU-curve
> Suitable for float charging
> Trickle charging

> Please read the operating instructions before use.
> Keep your charger in a dry place (indoor use only)
> Only for use within this specification
> In order to avoid the risk of fire and /or electrical shock, the charger must be protected
against high humidity and water
> Do not open or reconstruct the charger
> In case of defect, please return to an authorised service center
> Do not subject the equipment to high temperatures or to high humidity.
> To clean the charger, please disconnect it from the mains
> Only use a dry cloth for cleaning
> Do not operate the device without adult supervision
> Keep out of reach of children.
If the safety instructions are not followed, this may cause damage to the device or serious
injury to the user.

green LED “POWER” on: ready for use
red LED “CHARGE” on: charging of the battery
red LED “CHARGE” off: end of charging / trickle charging

Only for charging rechargeable lead acid batteries with 6 V (3 cells); 12 V (6 cells) or 24 V (12
cells). Do not charge other types of batteries - Danger of explosion!

Connect the battery with the battery clips of the charger. Pay attention to the correct polarity.
The red clip with (+), the the black clip with (-). Plug the charger into a convenient mains
socket. After connecting the charger will start the charging procure automatically. The green
LED shows reday for use, the red LED indicates charging. After charging the red charging LED
switches off and the battery is provided with trickle charging. The battery is now fully charged
and ready for use.

When charging lead acid cells, explosive gases can develop. Avoid open fire and sparks.

Input: 230V 50Hz
Voltage of the battery end of charging voltage max. charging current
ALCT6-24/1 ALCT 6-24/2
6 Volt 6,9 V 1000 mA 1500 mA
12 Volt 13,8 V 1000 mA 2000 mA
24 Volt 27,6 V 700 mA 1000 mA
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

ANSMANN ALCT 6-24/1 Operating instructions

ANSMANN
Brand
ANSMANN
Model
ALCT 6-24/1
Category
Battery chargers
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents