Monte Carlo Fan Company MCDF series Owner's Manual And Installation Manual

Brand: Monte Carlo Fan Company

Model: MCDF series

Category: Household fans

Type: Owner's Manual And Installation Manual

Owner’s Guide and Installation Manual

Fan adapter weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as your proof of purchase

To register your fixture, please visit our website www.montecarlofans.com

MCDF series

2.72 kgs

5.98 lbs

Shown with 5DS34XX

(Fan not included)

Install the fan adapter only with

4MC20, 3TF24, 4CO28 or 5DS34

series.

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

3/8/2012

1 2 3

4 5 6

Coupling

Rod

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble). Remove the two outlet

box screws provided with the box,

aligning the holes of the mounting

bracket with the holes of the outlet box.

Re-install the 2 outlet box screws

securely.

Remove preassembled rod from coupling

by removing 3 set screws. Keep screws

for later use.

Remove bolt, nut and set screw from

coupling. Keep the parts for later use.

Thread the lead wires and safety cable

from fan through the coupling.

Slip coupling onto the yoke of fan.

Aligning the holes on coupling and yoke

and then reinstall the bolt, nut and set

screw removed in step 5.

Note: Install bolt from the side with mark

(arrow).

Mounting bracket

3/8/2012

7 8 9

10 11 12

Thread lead wires and safety cable

through rod. (Note: Keep the safety

cable free inside of rod).

Aligning the marks (arrows) on rod

and coupling and slip the rod onto

coupling and then reinstall the set

screws remove in step 4.

Remove 3 preassembled set screws from

the other side of rod. Keep screws for

later use.

Remove bottom cover from fan adapter

assembly by removeing 4 set screws.

keep screws for later use.

Insert the rod ( rod assembled with fan )

into housing of fan adapter assembly.

aligning the holes on the rod and the

holes on the coupling seated inside

housing and then reinstall the set screws

removed it step 8.

Connect white wires from fans to white

wire from fan adapter. Blue wires from

fans to blue wire from fan adapter. Black

wires from fans to Black wire from fan

adapter.

If you want to install light kit on the

addapter. Use the light kit lead wires (as

shown in inset) provided, Connect white

wire with all other white wires together

and connect blue wires with all other blue

wires together.

Warning: Do not connect different

ﬁnishes of wires together. Wrong wire

connection may result in electric shock

hazard or serious personal injury.

Note: Refer to instruction manual of light

kit for light kit installation.

Reinstall the bottom cover removed in

step 9.

Fan adapter assembly

Rod

3/8/2012

13 14 15

16 17 18

Make wiring connections using wire

connectors provided as indicated above.

Connect white wire from fan to white wire

from house and then connect black and

blue wires from fan to black wire from

house. Connect all green grounded wires

to Grounded wire from House. Make sure

that no ﬁlaments are outside of the

wirenuts.

Note: This fan adapter is not available

with Remote controller.

Remove preassembled cross pin and

keeper pin from adapter housing yoke at

top of adapter assembly and partially

loosen downrod set screws.

Place downrod over canopy, canopy

bottom cap and yoke cover.

Slip downrod into adapter housing yoke,

align holes and reinstall cross pin and

keeper pin. Evenly tighten downrod set

screws on motor housing yoke.

Note: Refer to installation step 22 if you

want to replace downrod with longer one

(not included).

Determine the orientation of fan assembly

you want and Install ball end of downrod

into mounting bracket opening.

Warning: Make sure the ball end of

downrod engages with mounting bracket

well to avoid personal injury.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod mode the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the leadwires are longer

than the cable and no stress is placed on

the leadwires.

Loosen one and remove one

preassembled canopy mounting screw

from mounting bracket. Save canopy

mounting screw. Lift canopy up, aligning

its keyhole slot with the preassembled

screws on mounting bracket and twist

clockwise to lock in place. Re-install the

removed canopy mounting screw and

tighten all screws securely.

Attach canopy bottom cap onto canopy

by aligning its notches with the

preassembled canopy mounting screws

on mounting bracket and twist clockwise

until tight.

Refer to fan installation instruction manual

for blade assembly.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Black

White

Blue

Wall switch

Black

White

Green

Ground/Green

Cross pin

Keeper pin

Canopy

Canopy bottom cap

Yoke cover

Downrod

3/8/2012

20 21

Fan angle

adjustment

Remove coupling covers and then

Remove the set screw on both side of

coupling for the fan angle adjusting. Keep

screws.

Adjust the fan to the direction you want.

Align the holes on coupling and reinstall

the set screws remove in step 19.

Reinstall the coupling covers removed in

step 19.

It can be adjusted with 3 different angles

and the fans at both sides can be ﬁxed at

different angles.

Note: A slight wobble is possible with

some fan models. Adjust the fan speeds

and/or angle of the fans until wobble has

been eliminated.

If you want to replace downrod with

longer one (not included). Loosen the set

screw by allen wrench provided and

remove Pin and hanger ball from

downrod.

Place hanger ball on long downrod with

pin through downrod and seat in the slot

in hanger ball.

Tighten the set screw to hold downrod

with hanger ball securely.

Warning: Pin must be installed in slot

and through downrod

Downrod replacement

Downrod

Hanger ball

3/8/2012

Trouble Shooting

,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ

RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV

SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ

LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH

QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW

Warning%HIRUHVHUYLFLQJRUFOHDQLQJXQLW6ZLWFKSRZHU RII DW6HUYLFHSDQHO DQG ORFN VHUYLFH GLVFRQQHFWLQJ

PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH

ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO

&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV

&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII

,IWKLVIDQXVHVPDQXDO IRUZDUGUHYHUVH VZLWFK PDNHVXUH WKH VZLWFK LV SXVKHG ¿UPO\

HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG

&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW

&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK

RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ

CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ

&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH

6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV

$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU

DIWHUWKLVSHULRG

,IWKLV LV D GRZQURGPRXQWIDQ PDNHVXUH WKDW WKH ULGJHRI WKH FDQRS\ HQJDJHVWKH

QRWFKLQWKHGRZQURGEDOO

0DNHVXUH WKDW FDQRS\ PRXQWLQJEUDFNHWRU PRXQWLQJ SODWH DUH WLJKWHQHG VHFXUHO\WR

FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW

&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV

&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU

0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\

VHOHFWLQJD SRLQWRQ WKHFHLOLQJ DERYHWKHWLS RIRQH RIWKHEODGHV 0HDVXUHWKLV GLVWDQFH

IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH

LVSRVLWLRQHGIRU PHDVXUHPHQW 5HSHDWIRU HDFKEODGH,IDOOEODGHOHYHOV DUH QRWHTXDO

\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW

DZDVKHU QRW VXSSOLHG EHWZHHQWKHEODGH DQG EODGH KROGHU DWWKHVFUHZ FORVHVW WR WKH

PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH

KROGHUDW WKH WZR VFUHZV IDUWKHVW IURPWKHPRWRU5HYHUVH WKHSRVLWLRQRI WKH ZDVKHU LI

EODGHVPRXQWIURPWRSRIEODGH

,IEODGHZREEOHLVVWLOOQRWLFHDEOHLQWHUFKDQJLQJWZRDGMDFHQWVLGH E\VLGHEODGHV FDQ

UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ

&KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ

&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW

&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW

5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW

,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH

VXUHEDWWHU\LVHIIHFWLYH

CAUTION 0DNH VXUHPDLQSRZHU LV WXUQHG RII EHIRUHHQWHULQJVZLWFK KRXVLQJ DQGRU

FDQRS\

,IIDQVRXQGVQRLV\

,IIDQZREEOHV

,IOLJKWGRHVQRWZRUN

,IIDQGRHVQRWVWDUW

Trouble Suggested Remedy

Mar.2012

Monte Carlo Fan Company MCDF series Owner's Manual And Installation Manual

Brand: Monte Carlo Fan Company

Model: MCDF series

Category: Household fans

Type: Owner's Manual And Installation Manual

Download PDF

report

Monte Carlo Fan Company MCDF series Owner's Manual And Installation Manual

Monte Carlo Fan Company MCDF series Owner's Manual And Installation Manual

Related papers

Other documents