Brickcom MD-300Np-A4-Star Easy Installation Manual
- Type
- Easy Installation Manual
1
Easy Installation Guide
Megapixel Day & Night
Mini Dome Network Camera
English
2
Step 1.Check Package Contents
a. MD Series
b. Product CD
c. c, Warranty Card
d. Allen Key
e. Screw Bags(1pcs)
f. Dry Bag / Double-Sided Tape
g. Alignment Sticker
h. Easy Installation Guide
i. Mounting Adapter
(Optional)
j. TV out Connector Cable
(Optional)
k. Lens Adjustment Tool
(Optional)
l. M12 Connector (Optional)
Waterproof RJ45 Ethernet
Connector (Optional)
3
Step 2.Hardware Installation
WARNING: Do not mount the camera on a soft material. The camera may fall and be damaged.
1. Use the enclosed Allen key to detach the dome cover from the camera device.
As remove the cover, please be aware of the Microphone Line.
2. Remove the dry bag from its package. Use the double-sided tape to stick the dry bag onto
the designate position inside of the dome cover.
3. Choose the location on the wall or ceiling to place the camera. Attach the location sticker to
the desired spot. For ceiling installation, the best place to mount the camera is into a ceiling
stud.
4
4. Drill four holes through the center of the four location holes on the sticker.
5. Hammer the four plastic anchors which are provided in the product package into the four
location holes.
6. Please use the “Waterproof Tape” to wrap around the RJ45 connector, DC12V connector,,
in order to prevent water to seep in to the connectors.
5
7.
a. If you don't use the Mounting Adapter, please use the three shorter screws which are included in the
product package. Mount the camera on the wall or ceiling and position
the three screw slots over the plastic anchors. Insert the screws into the holes and use the screwdriver to
tighten the screws clockwise until they are secure.
b. If you do use the Mounting Adapter, please use the three longer screws which are included in the product
package. Mount the camera on the wall or ceiling and position the three screw slots over the plastic anchors.
Insert the screws into the holes and use the screwdriver to tighten the screws clockwise until they are secure.
You can use one of the remaining screws to fix the Mounting Adapter.
6
Step 3. Lens Adjustment
1. Please use the “Lens Adjustment Tool” to adjust the lens to the desired position.
2. Focus
a. Rotate the lens until the image in the Live View page is focused.
b. Remove the tool directly.
The camera can either be connected to a PoE switch or a non-PoE switch
a. Powering on Camera with PoE Switch:
Use an Ethernet cable to connect the camera to the PoE switch.
7
b. Powering on Camera with PoE Injector:
i. Use an Ethernet cable to connect the camera to a PoE Injector.
ii. Use an Ethernet cable to connect the PoE Injector to the non-PoE switch.
iii. Connect the PoE Injector to a power outlet.
Step 4.Installation Completed
Put the cover back on the camera and fix it by using the Allen Key
8
Step 5.Install the EasyConfig Software
Insert the CD into the CD-ROM, and follow the instructions of the InstallShield Wizard to finish installation.
Step 6.Launch EasyConfig
Launch the EasyConfig software, and click on the camera from the survey list to connect.
Follow the EasyConfig software to configure the camera’s IP address and EasyLink
TM
settings.
Step 7.Installation Completed
Click <Live View> to view the live video feed of the network camera.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Brickcom MD-300Np-A4-Star Easy Installation Manual
- Type
- Easy Installation Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Brickcom MD-300Np-360P Series Easy Installation Manual
-
Brickcom MD-300N Series User manual
-
-
-
-
-
-
Brickcom VD-130A V2 Series Quick Installation Manual
-
-
Brickcom VD-502A User manual