Parkside PNS 300 B2 Original Instructions Manual

Brand: Parkside

Model: PNS 300 B2

Category: Power tools

Type: Original Instructions Manual

Parkside PNS 300 B2 is a versatile power tool designed for a range of drilling and screwing tasks. With its two-speed gearbox, you can select the optimal speed for your project, whether you're working with wood, plastic, or metal. The drill's chuck allows for quick and easy bit changes, while the forward/reverse switch enables you to drive screws or remove them effortlessly.

IAN 321840

2-SPEED POWER DRILL

PNS 300 B2

2-SPEED POWER DRILL

Original instructions

Table of contents

1. Introduction ......................................................................................................................................... 05

Symbols used ...............................................................................................................................................................................................05

Scope of delivery ......................................................................................................................................................................................05

Parts list ............................................................................................................................................................................................................05

2. Technical data .................................................................................................................................... 05

3. Safety ...................................................................................................................................................... 06

Proper use ......................................................................................................................................................................................................06

Residual risks ................................................................................................................................................................................................06

General safety instructions for power tools ..............................................................................................................................06

Safety warnings for drills ......................................................................................................................................................................08

4. Before Use ........................................................................................................................................... 09

Check the drill and scope of delivery ...........................................................................................................................................09

Insert the drill bit or bit holder (Fig A) ...........................................................................................................................................09

Removing / mounting the chuck (Fig. B, C) ..............................................................................................................................09

Using the bit holder (Fig. D)................................................................................................................................................................09

5. Usage ...................................................................................................................................................... 09

Mains connection ......................................................................................................................................................................................09

Switching on and off (Fig. E) ..............................................................................................................................................................09

Speed selection (Fig. F) .........................................................................................................................................................................10

Forward / reverse switch (Fig G) ....................................................................................................................................................10

Driving screws (Fig. H) ...........................................................................................................................................................................10

Drilling ..............................................................................................................................................................................................................10

Work instructions .......................................................................................................................................................................................10

6. Maintenance, cleaning, storage and transport........................................................... 11

Maintenance ................................................................................................................................................................................................11

Cleaning..........................................................................................................................................................................................................11

Storage ............................................................................................................................................................................................................11

Transport .........................................................................................................................................................................................................11

7. Troubleshooting ............................................................................................................................... 12

8. Noise and vibrations levels ...................................................................................................... 13

9. Recycling ............................................................................................................................................... 13

Disposal of packaging ...........................................................................................................................................................................13

Disposal of the drill ...................................................................................................................................................................................13

10. Declaration of conformity....................................................................................................... 13

11. Warranty ........................................................................................................................................... 14

12. Service ................................................................................................................................................. 14

Congratulations on the purchase of your new

product. You have chosen a high quality product

with this purchase. This operating manual is an

integral part of this 2-speed mains-operated drill

(hereafter referred to only as the „drill“). It contains

important instructions on safety, use and disposal

of the product. Please familiarise yourself with all

operating and safety instructions before using the

product. Only use the product as described and

for the stated purpose. If the product is passed on

to a third party, please provide all documents to

the third party together with the product.

The following symbols and key words are used

in this operating manual, on the drill or on the

packaging.

1. Introduction

Symbols used

Parts list

Speed selector switch

Carbon brushes cover

Forward / reverse lever

Locking button

Handle

ON / OFF switch / Speed regulator

Torque adjustment ring

Chuck

Chuck unlocking mechanism

Torque setting mark

Drive spindle with a bit holder

Screwing bit, 50 mm

Read the operating manual.

Products marked with this symbol

comply with all applicable

regulations of the European

economic area.

Protection category 2

The „GS“ symbol stands for verified

safety. Products that are marked with

this symbol meet the requirements of the

German product safety law (ProdSG).

Indicates a hazard that, if not avoided, could

result in death or serious injury.

WARNING!

Signals a hazard that can cause injuries when

ignored.

CAUTION!

Warns against possible damages.

NOTE!

The model name on the drill is a combination of

letters and numbers:

PNS 300 B2

2-Speed Power Drill

Scope of delivery

• 2-Speed Power Drill

• Screwing bit, 50 mm

Model number PNS 300 B2

Mains connection 230 V

/ 50Hz

Rated power 300 W

No-load speed 1. Speed 0 – 400 min

-1

2. Speed 0 – 1600 min

-1

Max drilling

capacity:

Steel max. 10 mm

Wood max. 25 mm

Protection class II

2. Technical data

3. Safety

Proper use

The drill is designed for the following purposes:

- for screwing,

- for drilling in wood, plastic and metal.

The drill has to be used properly as specified.

It may not be used for any other purpose. The

manufacturer cannot be held responsible for

damage or injury caused by use the machine for

other than its intended purpose.

Only accessories that are appropriate for the

drill should be used. Non-observance of the

safety, assembly and operating instructions

while operating the appliance counts as misuse.

Anyone operating the drill and maintaining it has

to be familiar with the device and be aware of

the potential dangers. Any applicable health and

safety regulations must also be followed.

Any other applicable local and national

legislation must also be followed. Changes made

to the drill lead to loss of manufacturer liability

and any resulting damages.

The drill has not been designed for use in

commercial, business or industrial applications,

but for hobby and DIY users.

Any other use is expressly prohibited and is

considered as misuse.

Residual risks

Residual risks cannot be completely ruled out

even in case of proper use. The following risks

may arise due to the nature of the drill:

- Burns from coming into contact with hot parts of

the drill or workpiece.

- Harmful emissions of dust in poorly ventilated

spaces or inadequate extraction in closed

rooms.

- Injury and property damage caused by parts

flung out or tool attachment breakage.

General safety instructions for

power tools

WARNING!

Read all safety warnings,

instructions, illustrations and

specifications provided with this

power tool. Failure to follow all

instructions listed below may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions

for future reference.

The term „power tool“ in the warnings

refers to your mains-operated (corded)

power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep your work area clean and

well lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in

explosive atmospheres, such as

in the presence of ﬂammable

liquids, gases or dust. Power tools

create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders

away while operating a power

tool. Distractions can cause you to

lose control.

2. Electrical safety

a) Power tool plugs must match

the outlet. Never modify the

plug in any way. Do not use

any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching

outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed

or grounded surfaces, such as

pipes, radiators, ranges and

refrigerators. There is an increased

risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to

rain or wet conditions. Water

entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never

use the cord for carrying, pulling

or unplugging the power tool.

Keep cord away from heat, oil,

sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool

outdoors, use an extension cord

suitable for outdoor use.

Use of a

cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a

damp location is unavoidable,

use a residual current device

(RCD) protected supply.

Use of an

RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while

you are tired or under the

inﬂuence of drugs, alcohol or

medication. A moment of inattention

while operating power tools may

result in serious personal injury.

b) Use personal protective

equipment. Always wear eye

protection. Protective equipment

such as a dust mask, non-skid safety

shoes, hard hat or hearing protection

used for appropriate conditions will

reduce personal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off-

position before connecting to

power source and/or battery

pack, picking up or carrying the

tool. Carrying power tools with your

finger on the switch or energising

power tools that have the switch on

invites accidents.

d) Remove any adjusting key

or wrench before turning the

power tool on. A wrench or a key

left attached to a rotating part of the

power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the

power tool in unexpected situations.

f) Dress properly. Do not wear

loose clothing or jewellery. Keep

your hair and clothing away

from moving parts. Loose clothes,

jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the

connection of dust extraction

and collection facilities,

ensure these are connected

and properly used. Use of dust

collection can reduce dust-related

hazards.

h) Do not let familiarity gained

from frequent use of tools allow

you to become complacent and

ignore tool safety principles. A

careless action can cause severe injury

within a fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the

switch does not turn it on and

off. Any power tool that cannot be

controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the

power source and/or remove

the battery pack, if detachable,

from the power tool before

making any adjustments,

changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of

the reach of children and do

not allow persons unfamiliar

with the power tool or these

instructions to operate the

power tool. Power tools are

dangerous in the hands of untrained

users.

e) Maintain power tools and

accessories. Check for

misalignment or binding of

moving parts, breakage of

parts and any other condition

that may affect the power tool’s

operation. If damaged, have the

power tool repaired before use.

Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and

clean. Properly maintained cutting

tools with sharp cutting edges are

less likely to bind and are easier to

control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking

into account the working

conditions and the work to be

performed. Use of the power tool

for operations different from those

intended could result in a hazardous

situation.

h) Keep handles and grasping

surfaces dry, clean and free from

oil and grease. Slippery handles

and grasping surfaces do not allow for

safe handling and control of the tool

in unexpected situations.

5) Service

a) Have your power tool serviced

by a qualiﬁed repair person

using only identical replacement

parts. This will ensure that the safety

of the power tool is maintained.

Safety warnings for drills

Safety instructions for all types

of work

a) Brace the tool properly before

use. This tool produces a high

output torque and without properly

bracing the tool during operation,

loss of control may occur resulting

in personal injury.

b) Hold the power tool by

insulated gripping surfaces,

when performing an

operation where the cutting

accessory may contact hidden

wiring or its own cord. Cutting

accessory contacting a „live“ wire

may make exposed metal parts of

the power tool „live“ and could

give the operator an electric shock.

Safety instructions when using

long drill bits

a) Never operate at higher

speed than the maximum

speed rating of the drill bit.

At higher speeds, the bit is likely

to bend if allowed to rotate freely

without contacting the workpiece,

resulting in personal injury.

b) Always start drilling at low

speed and with the bit tip in

contact with the workpiece.

At higher speeds, the bit is likely

to bend if allowed to rotate freely

without contacting the workpiece,

resulting in personal injury.

c) Apply pressure only in direct

line with the bit and do not

apply excessive pressure. Bits

can bend causing breakage or loss

of control, resulting in personal

injury.

Check the drill and scope of

delivery

4. Before Use

WARNING!

Disconnect the machine from the

mains before performing any

maintenance or adjustments.

• Take the drill and accessories out of the

packaging.

• Check if the delivery is complete (see section

“SCOPE OF DELIVERY / DESCRIPTION OF

PARTS”).

• Check if the drill or the accessories are

damaged.

• Do not use the drill if it is damaged or parts are

missing. Contact the service centre listed on the

warranty card.

Insert the drill bit or bit holder

(Fig A)

• Turn the chuck

counterclockwise to open it

and insert a drill bit or bit holder.

• Choose

- a suitable drill bit and insert it into the chuck.

- a bit holder and insert it using the hexagonal

side into the chuck.

• Tighten the chuck clockwise.

• If you have mounted a bit holder, then insert a

suitable bit.

Removing / mounting the chuck

(Fig. B, C)

Removing the chuck:

To use the bit holder, you have to remove the

chuck

• Hold the chuck firmly at the front.

• Pull / push the chuck unlocking mechanism

in the direction of the chuck. The chuck is now

unlocked and can be removed from the front.

Mounting the chuck:

• To replace the drill, pull the chuck unlocking

mechanism

in the direction of chuck

and

push the chuck out completely.

Using the bit holder (Fig. D)

You can use the bit holder after removing the

chuck

as described in the section „Removing

the chuck“.

• Insert a suitable bit into the bit holder

• Slide the bit as fas as it goes into the bit holder.

The magnetic holder holds the bit.

• To remove the bit, pull the bit out of the bit

holder.

If the chuck does not lock by itself, turn

the chuck ring.

Mains connection

5. Usage

The drill is designed for use with single-phase AC

230 V

/ 50 Hz and has protective insulation.

Check whether the mains voltage of the socket

corresponds with the mains

voltage indicated on the drill’s rating label. Use

an extension cable if the work area is not close to

the mains outlet. Ensure an extension cable with

sufficient conductor diameter (min. 1.5 mm²) is

used. If necessary, ask the dealer for advice when

purchasing. The extension cable used should be

as short as possible. Ensure the mains cable does

not pose a tripping hazard.

Switching on and off (Fig. E)

Switching on:

• Press the On/Off switch

Switching off:

• Release the On/ Off switch.

Continuous usage:

• Press the On / Off switch and keep it pressed.

• Press the locking button

• Release the On / Off switch. The drill is now

running continuously at maximum speed at the

selected setting.

• Press the On / Off switch to stop continuous

operation.

Speed selection (Fig. F)

NOTE!

Operate the speed selection

only

when the drill spindle is stationary.

Otherwise there is a risk of

damaging the gearbox.

Speed selection switch in position 1:

• 1. Speed 0 – 400 min

-1

Speed selection switch in position 2:

• 2. Speed 0 – 1600 min

-1

Forward / reverse switch (Fig G)

NOTE!

Change the direction only when

the cordless drill is switched off.

Damage to the gear is prevented by

changing the speed properly.

• Select the direction of rotation by pressing the

switch

Switch with arrow facing forwards

(arrow pointing towards the chuck):

- Forward

Switch with arrow facing backwards

(arrow pointing away from the chuck):

- Reverse

Driving screws (Fig. H)

NOTE!

Do not use speed 2 (drilling) for

screwing (risk of overload).

The required torque can be adjusted using the

torque adjustment ring

for flush-mounting screws.

• Set the torque adjustment ring to the desired

torque (1-22). To do this, use the setting mark

• The torque adjustment ring engages noticeably.

Drilling

• To select the drilling mode, rotate the torque

adjustment ring

until the drill symbol lines up

with the setting mark

Tips for drilling in metal

Make an indentation at the desired hole location

using a centre punch. Always secure sheet

metal using an appropriate clamping device.

When drilling thin sheets of metal lay a piece

of wood underneath the workpiece to prevent

deformation. Use only well sharpened HSS spiral

drill bits. If a large hole diameter is required, drill

a pilot hole using a smaller bit first. When drilling,

the diameter of the smaller drill should be at least

as large as the core of the larger drill. The drill

core is the shortest distance between the two

cutting edges.

Work instructions

CAUTION!

Always secure your workpiece

in a vice or in any other clamping

device. Secure particularly large

workpieces against sliding or

support them properly.

Tips for drilling wood

Make an indentation at the desired hole location

using a centre punch or nail. Place a piece of

waste wood under the workpiece or drill the hole

from both sides to avoid damaging the workpiece

at hole breakthrough. The maximum bore diameter

can only be achieved with a Forstner drill.

Screw driving:

Use screwdriver bits of the appropriate sizes

and shapes for your application. Suitable screws

can be driven into soft wood without pre-drilling.

Drilling in hardwood is very advantageous. In

case of countersink screws, drill a countersunk

bore hole. When using screws with a partial

thread, drill a pilot hole approximately half the

length of the screw.

Steel: Oil

Aluminium: Turpentine or paraffin

Brass, copper, cast

iron:

No lubricant (remove

the drill from the hole

regularly to aid cooling)

Using lubricants:

6. Maintenance, cleaning,

storage and transport

WARNING!

Disconnect the machine from the

mains before performing any

maintenance or adjustments.

Maintenance

The drill is maintenance free.

Only use spare parts / accessories from the

manufacturer or authorised and qualified

workshops.

Repairs should only be carried out by qualified

technicians or by an authorised service centre.

Qualified technicians must have relevant training

and experience, be familiar with the design and

construction requirements of the product and

understand and follow the safety regulations.

Keep your tool bits always sharp. Sharpen them

always using a suitable tool as recommended by

the tool bit manufacturer.

NOTE!

Use only suitable carbon brushes.

In case of doubt, please contact the

manufacturer.

Replacing the carbon brushes

• Unscrew the carbon brush cover using a

screwdriver.

• Remove the carbon brush.

• Replace the carbon brush with a new one.

• Replace the cover of the carbon brushes.

Replacing the mains cable

If the mains cable needs to be replaced, it has to

be done by the manufacturer or his representative

to avoid safety hazards.

WARNING!

Make sure that liquids do not get

inside the drill.

Cleaning

• Clean the drill regularly with a dry cloth. Never

use strong and / or abrasive cleaning agents or

solvents. Allow all the parts to dry completely.

• Ensure that the ventilation slots are not blocked

and clean the tool‘s housing regularly with a

soft cloth.

Storage

• Clean the drill before storage.

• Keep the drill in a safe, cool, dry and well-

ventilated place, out of the reach of children

when not in use.

• Store the drill at an ambient temperature of

0 - 40 ° C.

Transport

• Use the original packaging and secure the drill

in place during transport.

• Always carry the drill using the handle provided

for this purpose.

Problem Possible cause Rectification

The drill does not start. Damaged cable. Check the cable.

Fuse tripped. Check the household fuse box

The carbon brushes are worn. Replace the carbon brushes.

Trigger defective Have the trigger switch checked by

customer service

Poor drilling performance. Drill bit is blunt. Sharpen or replace the drill bit.

7. Troubleshooting

8. Noise and vibrations

levels

Tested according to EN 62841. The noise level

at the workplace may exceed 80 dB (A); safety

precautions are required for the operator in this

case (wear suitable hearing protection device).

Sound pressure level: L

88,2 dB(A)

Sound power level: L

99,2 dB(A)

Uncertainty: K

3 dB

Noise emission levels

Vibration details

Vibration level: a

h,D

3,9 m/s

Uncertainty: K 1,5 m/s

The overall vibration values and the noise

emission values specified have been measured

according to a standardized test method and can

be used to compare one power tool with another.

The overall vibration values and the noise

emission values specified can also be used for a

preliminary estimation of the load.

WARNING!

The vibration and noise emissions during the

actual use of the power tool may differ from the

specified values, depending on the manner in

which the power tool is used, especially, the type

of workpiece being machined

Safety measures may be required to protect the

operator that are based on an estimate of the

vibration load during actual usage conditions (in

this case all the parts of the operating cycle have

to be considered, such as times when the power

tool is turned off, and those where, the tool is

turned on, but is running without load).

9. Recycling

Disposal of packaging

Disposal of the drill

Dispose of packaging separately. Dispose

of card and paper in waste paper, plastic

at collection points.

This symbol indicates that this product

may not be disposed of together with

domestic waste in compliance with the

(2012/19/EC) directive pertaining to

waste electrical and electronic devices (WEEE).

This product must be handed in at an designated

collection point. This can occur, for example, by

returning it when a similar product is purchased

or by handing it in at an authorised collecting

point for the recycling of waste electrical and

electronic equipment. Owing to potentially

hazardous substances that are frequently

contained in waste electronic equipment,

incorrect handling of waste equipment may have

a negative impact on the environment and on the

health of human beings. By disposing of this

product correctly, you are also contributing

towards an efficient use of natural resources.

Information on collecting points for waste

equipment can be obtained from your local

authority, the public waste disposal authority, an

authorised institution for the disposal of waste

electrical and electronic equipment or the waste

collection services. Dispose of device and

packaging in an environmentally friendly manner.

10. Declaration of

conformity

The EU declaration of conformity can be found

on the penultimate page of this manual.

Warranty provided by Walter

Werkzeuge Salzburg GmbH

Dear customer,

This device comes with a 3 year warranty

from the date of purchase. In case of defects

in the product you may be entitled to legal

claims against the seller of the product. These

legal claims are not restricted by the following

warranty.

Conditions of warranty

The warranty period begins with the date of

purchase. Please preserve the original sales

receipt. This document is required as proof of

purchase. If a material or fabrication defect

occur in this prodict within three years from the

date of purchase, the product shall be repaired

or replaced free of cost at our discretion. Within

the three year period the warranty requires the

defective product and the purchase document

(sales receipt) to be provided with a brief written

description of where the defect lies and when it

occurred.

If the defect is covered by our warranty, the

repaired product or a new product shall be

returned to you. A new warranty period does not

begin with the repair or exchange of the product.

Warranty period and legal claims based

on defects

The warranty period is not extended by the

warranty. This also applies to replaced and

repaired parts. Any damages and defects that

may exist at the time of purchase must be notified

immediately after removal from packaging. Any

repairs arising after the expiry of the warranty

period are chargeable.

Scope of the warranty

The device has been manufactured according

to strict quality guidelines and tested diligently

before delivery. The warranty applies to material

or fabrication defects. This warranty does not

cover product parts that are subject to normal

wear and tear and therefore can be considered

as parts subject to wear and tear or for the

damage to fragile parts, e.g switch, batteries or

those made of glass.

This warranty is void if the product is damaged,

not used or maintained properly. All the

11. Warranty

instructions provided in the operating manual

must be followed exactly for proper use of the

product. The purpose of use and actions which

are advised or warned against must necessarily

be avoided.

The product is intended solely for private use and

not for professional use. The warranty is void in

case of misuse or improper handling, use of force

and changes that have not been carried out by

our authorised service centre.

Processing a warranty case

To ensure quick processing of your issue, please

follow the below instructions:

• Please be ready with the sales receipt and the

product number (e.g. IAN 12345) as proof or

purchase for all queries.

• You can refer the product number from the type

label, an engraving, on the cover sheet of your

operating instructions (below left) or as sticker

on the back or lower side.

• If functional or other defects occur, first call or

email the following service department.

• You can then send a product recorded as

defective postage free along with the sales

receipt and information about where the defect

lies and when it has occurred, to the service

centre address provided to you.

This and many other manuals, product videos and

software can be downloaded at

www.lidl-service.com

12. Service

Walter Werkzeuge Service Center

E-Mail: [email protected]

Tel.: 00800 925 837 88

IAN 321840

Supplier:

Please note that the following address is not a

service centre address. Please contact the above-

mentioned service centre first.

Walter Werkzeuge Salzburg GmbH

Gewerbeparkstr. 9

5081 Anif

Austria

IAN 321840

Walter Werkzeuge Salzburg GmbH

Gewerbeparkstr. 9

5081 Anif, Österreich

V. 1.0

Last Information Update:

08/2019

Parkside PNS 300 B2 Original Instructions Manual

Brand: Parkside

Model: PNS 300 B2

Category: Power tools

Type: Original Instructions Manual

Download PDF

report

Parkside PNS 300 B2 Original Instructions Manual

Parkside PNS 300 B2 Original Instructions Manual

Related papers

Other documents