Marantec Comfort 580 Control x.51 Owner's manual

Comfort 580 / Control x.51

Operator system for Hinged Gates

GB

Manual for installation and operation

1. Meaning of symbols

Caution!

Danger of personal injury!

The following safety advice must

be observed at all times so as to avoid

personal injury!

Attention!

Danger of material damage!

The following safety advice must

be observed at all times so as to avoid

material damage!

Advice / Tip

Check

Reference

i

Photocell or closing edge safety device (CESD)

Gate position OPEN

Has no function

Gate position CLOSED

Reference control point

Has no function

Impulse

(remote control, external control elements)

Operation

Closing edge safety device

STOP

External control elements

Modular antenna

Controls and motor unit symbols Advice

Type plate on motor unit 2 (only double wing)

Type: ________________________________________________

Art. No.: _____________________________________________

Product No.: __________________________________________

Type plate on motor unit 1

Type: ________________________________________________

Art. No.: _____________________________________________

Product No.: __________________________________________

Type plate on control unit

Type: ________________________________________________

Art. No.: _____________________________________________

Product No.: __________________________________________

2 Manual for installation and operation, Comfort 580 GB (#82762)

Table of contents
Meaning of symbols  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
General safety advice  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Product overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1 Comfort 580 supply package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2 Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3 Gate variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Preparation for mounting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
1 General notes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2  Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3 Gate and foundation layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4  Cabling layout  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1 Mounting conditions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2 Installing the foundation box  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3 Installing the motor unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4 Mounting the telescopic arm  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
5 Release  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
6 Fixing the control unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
7 Connection of control elements   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
8 Connecting the motor unit to the controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
9 Connection of the mains cable   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Hand transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
1 Operation and accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
2 Hand transmitter coding   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Initial operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
1 Connecting the modular antenna  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
2 Overview of the control unit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3 Overview of the display functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4 Reference point  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5 Express programming  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
6 Function test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Extended operator functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
1 General notes on extended operator functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
2 Programming structure for extended operator functions (Example for Level 2, Menu 2) . . . . . . . . . . . . .37
3 General overview of the programmable functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
4 Functions overview for the levels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
1 Status messages   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
2  Fault messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
3 Rectifying faults  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Attachment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
1 Connection diagram Comfort 580  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
2 Technical data for Comfort 580  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
3 Declaration of incorporation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
4 EC Declaration of Conformity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Manual for installation and operation, Comfort 580 GB (#82762) 3

Please read carefully!

Target group

This operator system may only be installed, connected and put into operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working with electricity,

- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed. Disregarding these

warnings may lead to personal injury or material damage. If this advice is disregarded, the manufacturer will not be

liable for damages that might occur.

Batteries, fuses and bulbs are excluded from warranty.

To avoid installation errors and damage to the gate and operator system, it is imperative that the installation

instructions are followed. The system may only be used after thoroughly reading the respective mounting and

installation instructions.

The motor unit may not be opened, otherwise the guarantee is void.

The installation and operating instructions are to be given to the gate system user, who must keep them safe.

They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned in the Manufacturer's Declaration and in

the Declaration of Conformity. The product has left the factory in perfect condition with regard to safety.

Power-operated windows, doors and gates must be checked by an expert (and this must be documented) before they

are put into operation and thereafter as required, but at least once a year.

Correct use

The operator system is designed exclusively for opening and closing hinged doors and gates.

Gate requirements

The Comfort 580 operator system is suitable for:

- hinged gates with a gate wing width of 2.50 m and a gate wing weight of 250 kg.

Beside the advice in these instructions, please observe the general safety and accident prevention regulations!

Our sales and supply terms and conditions are effective.

3. General safety advice

4 Manual for installation and operation, Comfort 580 GB (#82762)

Information on installing the operator system

• Ensure that the gate is in good mechanical condition.

• Ensure that the gate opens and closes properly.

• Remove all unnecessary components from the gate (e.g. cables, chains, brackets).

• Render any installations inoperable that will no longer be needed after the operator system has been installed.

• Before commencing cabling works it is very important to disconnect the operator system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid separately. The controls voltage is 24 V DC.

• Install all the impulse transmitters and control devices (e.g. remote control buttons) within sight of the gate and at a

safe distance from the moving parts of the gate. A minimum installation height of 1.5 m must be observed.

• Ensure that no part of the gate extends across public footways or roads when the installation is complete.

Information on commissioning the operator system

After initial operation, the persons responsible for operating the gate system, or their representatives must be

familiarised with the use of the system.

• Make sure that children cannot access the gate control unit.

• Before moving the gate, make sure that there are neither persons nor objects in the operating range of the gate.

• Test all existing emergency command devices.

• Never insert your hands into a running gate or moving parts.

• Pay attention to any parts of the gate system that could cause crushing or shearing damage or accidents.

The EN 13241-1 regulations must be observed.

Information on servicing the operator system

To ensure proper operation, the following items must be checked regularly and repaired if necessary.

Before any works to the gate system are undertaken, the operator system must be disconnected from the mains.

• Check once a month that the operator system stops and reverses in every position when the gate touches an

obstacle. Place an obstacle in the path of the gate to check this.

• Check the settings of the OPEN and CLOSE automatic cut-out function.

• Check all movable parts of the gate and operator system.

• Check the gate system for signs of wear or damage.

• Check whether the gate can be easily moved by hand.

• Inspect the telescopic arms for dirt and corrosion.

Remove any dirt. Grease the sliding seats on the telescopic arms.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully!

3. General safety advice

Manual for installation and operation, Comfort 580 GB (#82762) 5

6 Manual for installation and operation, Comfort 580 GB (#82762)

4.1 Comfort 580 supply package

4. Product overview

4.1 / 1

1

2

Single wing gate system

1 Foundation box

2 Motor unit

3 Telescopic arm

4 Shims (4x)

5 Spacer cylinder

6 Cover plate

7 Protective rubber fitting

8 Set of screws for bracket

4.1 / 3

9 Control x.51

10 Handle

1 Foundation box (2x)

2 Motor unit (2x)

3 Telescopic arm (2x)

4 Shims (8x)

5 Spacer cylinder (2x)

6 Cover plate (2x)

7 Protective rubber fitting (2x)

8 Set of screws for bracket (2x)

Double wing gate system

Control unit

3

4

5

The Comfort 580 standard delivery package comprises:

- motor unit

- controls

- fixing materials for controls

and motor unit

- remote control

The Comfort 580 is available in the following versions,

as required:

9

6

7

8

1

2

3

4

5

6

7

8

4.1 / 2

!¯

4. Product overview

Manual for installation and operation, Comfort 580 GB (#82762) 7

!5

!”

!#

!£

!Ø

4.1 / 4

11 Screws 3.5 x 32 (4x)

12 Wall plugs S6 (4x)

13 13 Spacer elements (2x)

14 Screw fixing insert with 2 flat cable openings

15 M20 screw fixing with flat cable insert

16 M20 screw fixing with round cable insert

17 M16 screw fixing with round cable insert

Mounting kit for control unit

!^

4.1 / 5

18 Hand transmitter

19 Sun visor clip

20 Module antenna

21 Transmission plug

Remote control

!\

!˜

!·

„¯

4.2 / 1

Comfort 580

4.2 Dimensions

„∏

150

300

168

112

270

72

8

8 Manual for installation and operation, Comfort 580 GB (#82762)

4.3 / 1

The standard supply package is suitable for

the following types of gate.

Single wing gate system

4.3 / 2

Double wing gate system

5.1 General notes

The pictures in these instructions are not true-to-scale.

Dimensions are always given in millimetres (mm)!

The motor unit and the controls must be mounted on

the inside of the gate system.

For correct mounting you will need the following

tools:

5.1 / 1

13 / 17 / 22 / 24 13

2 2 / 5 ø 6 ø 6.5

M 8

5. Preparation for mounting

4.3 Gate variations

4. Product overview

5.2 Checks

Attention!

In order to guarantee correct

mounting, carry out the following

checks before installing.

5. Preparation for mounting

Advice:

The use of an electric lock is

recommended.

Foundations

• Check the proposed position of the foundation.

Supply package

• Check the package to ensure that all the parts are

included.

• Check that you have all the additional components

that are necessary for your particular installation

requirements.

Gate system

• Ensure that your gate system has an appropriate

electricity supply connection and a facility for

disconnecting the mains. The minimum cross-

sectional area of the earth cable is 3 x 1.5 mm

2

.

• Ensure that all cables are suitable for outdoor use

(UV resistant and cold resistant).

• Ensure that your gate system has a gate stop in the

CLOSE and OPEN directions.

• Disassemble the door latches or render them inop-

erable.

• Ensure that the gate can be easily moved by hand.

• Observe the following gate requirements.

Gate wing width: min. 1 m - max. 2.5 m

Gate height: max. 2.5 m

Gate wing weight: max. 250 kg

Open space: min. 50%

Gate incline: The gate must be horizontal.

Manual for installation and operation, Comfort 580 GB (#82762) 9

10 Manual for installation and operation, Comfort 580 GB (#82762)

5. Preparation for mounting

A Conduit for control cable

B Drainage pipe for foundation box

q Gate length (max. 2.50 m)

r Below the depth of frost penetration

5.3 Gate and foundation layout

r

A

B

5.3 / 1

Attention!

In order to avoid damage to the foundation,

- the specified size of the foundation must be adhered to,

- the foundation box must be positioned at the centre of the foundation.

Motor unit parallel to the gate

r

q

A

B

5.3 / 2

Motor unit at right angles to the gate

q

>250

> 400

>250

>400

Manual for installation and operation, Comfort 580 GB (#82762) 11

5. Preparation for mounting

5.4 Cabling layout

5.4 / 1

2 x 0.75 mm

2

8 x 0.75 mm

2

8 x 0.75 mm

2

2 x 0.4 mm

2

2 x 0.4 mm

2

2 x 0.4 mm

2

2 x 0.4 mm

2

3 x 1.5 mm

2

230 V / AC

3 x 1.5 mm

2

Advice:

This is just an example of a cabling layout; the layout can vary according to the type of gate and the

associated equipment.

Reference:

The relevant instructions are to be followed for the installation and cabling of the gate sensors and

the operating and safety elements.

i

1 Photocell

2 Photocell

3 Signal light

4 Code button, transponder, ...

5 Key switch

6 Mains isolator switch (mains disconnection facility)

7 Electric lock

8 Stop plate

9 Mains supply cable

10 Closing edge safety device (CESD)

2

23

4

6

9

7

1

8

!¯

5

12 Manual for installation and operation, Comfort 580 GB (#82762)

6.1 Mounting conditions

6.1 / 1

Mounting position of motor unit

Attention!

To ensure proper operation,

- the foundation box must be concreted

in place in a foundation block,

- all the specified conditions must be

met,

- all the specified dimensions must be

complied with.

6.1 / 2

The distance between the upper edge of the foundation

box and the lower edge of the gate wing must be at

least 55 mm.

6.2 Installing the foundation box

• Place the foundation box (A) in the prepared opening.

• Position the foundation box (A) in the middle of the

opening. Observe the specified installation conditions.

• Connect the conduit (B) for the control cable to the

foundation box (A).

• Connect the drainage pipe (C) to the foundation

box.

• Seal the joints where the conduit (B) and the drainage

pipe (C) connect to the foundation box (A).

6.2 / 1

• Place the spacer cylinder (D) in the foundation box (A).

6.2 / 2

Clearance between gate wing and ground

Advice:

For greater clearance values, a suitable

fitting must be fixed to the gate.

≤ 100430 - 470

0 - 40

> 55

A

B

C

A

D

6. Installation

Manual for installation and operation, Comfort 580 GB (#82762) 13

6. Installation

• Close the foundation box (A) with the cover plate (E).

• Seal the cover plate (E) using self-adhesive tape.

6.2 / 3

A

E

• Infill the space surrounding the foundation box with

concrete.

6.2 / 4

Advice:

To ensure that the motor unit functions

properly, the foundation box must not

be allowed to change position during

concreting.

• Check that the foundation box is horizontal.

• Allow the foundation concrete to set.

• Remove the self-adhesive tape and the cover plate (E).

• Remove the spacer cylinder (D).

6.2 / 5

Attention!

To prevent damage to the foundations

occurring and the drive position from

slipping, the foundation block must

have set completely before the next

step is carried out.

D

E

6. Installation

6.3 / 1

Attention!

To allow the motor unit to be taken

out at a later date, at least 35 cm of

control cable must be left loose in the

foundation box.

6.3 Installing the motor unit

• Place the four galvanised shims (A) in the corners of

the foundation box (B).

6.3 / 2

• Feed the control cable through the conduit.

• Pull the cable through to its connection position at

the control unit.

• Lower the motor unit (C) into the foundation box (B).

14 Manual for installation and operation, Comfort 580 GB (#82762)

A

B

C

Tip:

If the motor unit has to be taken out of

the foundation box at a later date, two

of the screws can be replaced with the

longer screws (supplied) to make this

process easier. Before lowering the

motor unit back into the foundation

box, the short screws must be put back

into place.

6.3 / 3

6. Installation

Manual for installation and operation, Comfort 580 GB (#82762) 15

6.4 / 1

6.4 Mounting the telescopic arm

• Place the protective rubber fitting (B) on the telescopic

arm (C).

• Push the protective rubber fitting (B) tightly onto the

motor unit.

• Push the telescopic arm (C) on to the motor unit (A).

Advice:

The telescopic arm must be mounted

between the OPEN and CLOSED

positions. The mounting position

ensures that the reference point is

switched with every gate movement.

B

A

C

6.4 / 2

• Drive the gate to the gate OPEN position.

• Drive the gate to the gate CLOSED position

If the telescopic arm has an overlap of at least

90 mm whatever the gate position, the bracket can

be screwed to the gate.

• Screw the bracket to the gate.

C

> 90

Before the telescopic arm can be permanently fixed to

the gate, the correct position for the bracket screws

must be determined. In order to adjust the bracket

position, the motor unit must first be connected to the

control unit.

• Clamp the bracket of the telescopic arm (C) securely

to the gate using a screw clamp.

• Connect the motor unit to the control unit.

• Put the control unit into operation.

Reference:

Connecting the motor unit to the

control unit is described in Section 6.8.

Putting the control unit into operation

is described in Sections 8.1 to 8.6.

i

6. Installation

6.6 / 1

6.6 Fixing the control unit

6.5 Release

• Open the control unit.

• Mount the control unit using the spacer elements (A).

3.5 x 32

Attention!

The control unit must be installed in

such a way that the motor cable can be

fed through the screw fixing at the

base of the control unit.

6.6 / 2

A

Reference:

Mounting the telescopic arm is

described in Section 6.4.

i

16 Manual for installation and operation, Comfort 580 GB (#82762)

Releasing

• Remove the screw (A) and the spacer.

• Pull out the telescopic arm (B).

• Lift the remaining section of the telescopic arm off

the motor unit.

6.5 / 1

B

A

Tip:

If the telescopic arm can not be

separated from the motor unit, an

M12 x 35 screw can be screwed into

the screw thread (C). This will lift the

telescopic arm off the motor unit.

Before mounting the telescopic arm on

the motor unit again, this screw must

be removed.

The motor unit is now no longer coupled to the gate.

The gate can be moved manually.

Locking

To couple up the gate again, the telescopic arm must

be mounted on the motor unit again and fixed to the

bracket.

C

6. Installation

6.7 Connection of control elements

Attention!

In order to avoid damaging the

controls:

- The local safety regulations must be

complied with at all times.

- It is very important that mains cables

are laid separately from control cables.

- The controls voltage must be 24 V DC.

- If external voltages are applied at

terminals XM70A, XV51A, XM70B,

XV51B, XB99, XP54B, XP54A, XP62B,

XP62A or XB70, the entire electronic

system will be destroyed.

- Only potential-free contacts may be

connected to terminals B9, 5, 34, 3

and 8 (XB99).

- The connections XM70B and XV51B

are not to be used!

Caution!

Danger of electric shock:

Before any cabling works begin, it must

be ensured that the cables are

disconnected from the power supply.

During cabling works, it must be

ensured that the cables remain

disconnected from the power supply at

all times (e.g. prevent reconnection).

Label Type / function

i

XB70 Connection of modular antenna 8.1

XB99

Connection of external control

elements

6.7 / 2

6.7 / 3

6.7 / 4

6.7 / 5

XH01

Connection for programmable

output 16/17 (e.g. signal light,

24 V DC, 0,5 A)

Wiping impulse 15/16

6.7 / 6

6.7 / 7

XM70A

Connection for motor unit

(MASTER)

6.8 / 4

6.8 / 7

XM70B

Connection for motor unit

(SLAVE)

6.8 / 4

6.8 / 7

XN70

Connection Battery Backup

(if available)

-

XN81 Connection for mains cable

6.7 / 6

6.9

XP54A

Connection for closing edge

safety device, gate travelling

direction CLOSE

6.7 / 8

XP54B

Connection for closing edge

safety device, gate travelling

direction OPEN

6.7 / 8

XP62A

Connection for photocell,

gate travelling direction CLOSE

6.7 / 9

XP62B

Connection for photocell,

gate travelling direction OPEN

6.7 / 9

XV51A

Connection for rpm detector

and reference point sensor

(MASTER)

6.8 / 3

6.8 / 7

XV51B

Connection for rpm detector

and reference point sensor

(SLAVE)

6.8 / 3

6.8 / 7

Manual for installation and operation, Comfort 580 GB (#82762) 17

P

1

2

3

4

5

6

7

8

1

2

L

N

PE

15

16 17

6.7 / 1

XN81

XV51B

XM70B

XM70A

XV51A

XB99

XP54A

XB70

XP54B

XH01

XP62A

XN70 XP62B

18 Manual for installation and operation, Comfort 580 GB (#82762)

6. Installation

Connection option 2:

Reference:

The connection configuration depends

on the programming of the special

functions. Depending on the program-

ming, impulse or direction buttons can

be connected.

Programming the special functions is

described in Section 9.4 (Level 5).

i

-SB5

12 11

-SB3

14 13

-SB3 4

12 11

-SB8

14 13

-XB99

B9 5 34 3 8

6.7 / 4

Label Type / function

3 Connection for intermediate position

5 Stop connection

8 Impulse connection

34 Connection for closing prevention device

B9 +24 V DC connection

SB3 Button for intermediate position

SB5 STOP button

SB8 Impulse button

SB34

Button for closing prevention device /

Drive system stops and reverses

M06E039

-XB99

B9 5 34 3 8

M06E039

Terminal XB99

Factory settings:

B9 and 5 bridged

Connection option 1:

-SB5

12 11

-SB8

14 13

-XB99

B9 5 34 3 8

6.7 / 2

6.7 / 3

M06E039

Reference:

When installing external control

elements, or safety and signal

equipment, the relevant instructions

must be observed.

i

- XB99

B9 5

34

3 8

- XH01

15 16 17

- X1

+

-

- S1

14 13

1 2

M07E027

Manual for installation and operation, Comfort 580 GB (#82762) 19

6. Installation

Advice:

If a closing prevention device

(photocell, timer, …) is connected to

XB99, the controls will recognise it

automatically after “Mains On”

(contact SB34 must be closed).

The photocell can be deactivated later

(Level 8 / Menu 1).

When the contacts of a closing

prevention device are open, the gate

can no longer be closed.

Additional external control elements,

and safety and signal devices with 24 V

connections must be connected to

XB99 and XH01.

Connection option 3:

- External radio receiver

6.7 / 5

Label Type / function

XB99 Connection of external control elements

3 Connection for intermediate position

5 Stop connection

8 Impulse connection

34 Connection for closing prevention device

B9 24 V DC connection

X1 Connection for external receiver

1

Connection of potential-free normally open

contact

2

Connection of potential-free normally open

contact

+ 24 V DC connection

- GND connection

S1

Normally open contact, receiver,

potential-free

XH01 Connection of control unit output

15 Connection for electric lock, 24 V DC

16 GND connection

17 Connection for programmable output

Terminals XN81/XH01 Connection option:

- Connection for signal light with external relay

20 Manual for installation and operation, Comfort 580 GB (#82762)

6. Installation

- XN81

- X0

L

PE

N

L

PE

- F0

L

N

PE

6.7 / 6

16

15

17

- YH15

- HH17

- XH01

16

15

17

1411

12

A2 A1

- KH17

- HH14

L

N

M07E039

M07E038

6.7 / 7

M07E038

Label Type / function

L Connection for phase

N Connection for neutral wire

PE Earth wire connection

15 / 16 Connection for electric lock, 24 V DC

16 GND connection

16 / 17

Connection of programmable output

(24 V DC / 0.5 A)

HH14 Signal light

HH17 Signal light 24 V

KH17 User’s relay 24 V

YH15 Electric lock (provided by the customer)

Page is loading ...

Marantec Comfort 580 Control x.51 Owner's manual

Marantec Comfort 580 Control x.51 Owner's manual

Related papers

Other documents