TP-LINK EAP110 User manual

User Guide

Omada Controller Software

1910012624 REV 3.4.0

July 2019

CONTENTS

1 Quick Start ....................................................................................................................... 1

1.1 Determine the Network Topology .........................................................................................................................2

1.1.1 Management on the local Network ............................................................................................................... 2

1.1.2 Management via Cloud Access......................................................................................................................4

1.2 Install Omada Controller Software ........................................................................................................................5

1.2.1 Installation on Windows Host .......................................................................................................................... 5

1.2.2 Installation on Linux Host ................................................................................................................................. 5

1.3 Inform the EAPs of the Controller Host's Address ..........................................................................................7

1.4 Start and Log In to the Omada Controller ...........................................................................................................8

1.4.1 Launch Omada Controller ................................................................................................................................ 9

1.4.2 Do the Basic Configurations............................................................................................................................9

1.4.3 Log In to the Management Interface ......................................................................................................... 12

1.5 Create Sites and Adopt EAPs ............................................................................................................................... 13

1.5.1 Create Sites ........................................................................................................................................................ 13

1.5.2 Adopt the EAPs ................................................................................................................................................. 16

1.6 Monitor and Manage the EAPs ............................................................................................................................. 17

2 Monitor and Manage the Network .........................................................................18

2.1 View the Statistics of the Network .....................................................................................................................19

2.1.1 View the Client Distribution on SSID ......................................................................................................... 19

2.1.2 Have a Quick Look at EAPs and Clients ................................................................................................... 19

2.1.3 View Current Usage-Top EAPs ................................................................................................................... 20

2.1.4 View Recent Activities .................................................................................................................................... 20

2.2 Monitor the Network with the Map .....................................................................................................................21

2.2.1 Add a Map ............................................................................................................................................................ 21

2.2.2 Monitor the EAPs on the Map ...................................................................................................................... 24

2.3 Monitor and Manage the EAPs ............................................................................................................................. 25

2.3.1 Manage the EAPs in Different Status ........................................................................................................ 25

2.3.2 View the Detailed Information of EAPs..................................................................................................... 26

2.3.3 Manage the EAPs in the Action Column .................................................................................................. 26

2.4 Monitor and Manage Clients ................................................................................................................................. 28

2.4.1 View the Current Information of Clients .................................................................................................. 28

2.4.2 Manage Clients in the Action Column ....................................................................................................... 28

2.5 View Clients Statistics During the Specified Period ...................................................................................29

2.5.1 Select a Specified Period .............................................................................................................................. 29

2.5.2 View the History Information of Clients ................................................................................................... 30

2.5.3 Manage Clients in the Action Column ....................................................................................................... 30

2.6 Manage the Rogue APs List ..................................................................................................................................30

2.6.1 Manage the Untrusted Rogue APs List .................................................................................................... 31

2.6.2 Manage the Trusted Rogue APs List ......................................................................................................... 31

2.7 View Past Guest Authorization .............................................................................................................................32

2.8 View Logs .....................................................................................................................................................................32

3 Configure the EAPs Globally ...................................................................................34

3.1 Wireless Network ......................................................................................................................................................35

3.1.1 Add Wireless Networks .................................................................................................................................. 35

3.1.2 Configure Advanced Wireless Parameters ............................................................................................ 45

3.1.3 Configure Band Steering ............................................................................................................................... 47

3.1.4 Configure Mesh ................................................................................................................................................. 48

3.2 Access Control ..........................................................................................................................................................53

3.3 Portal Authentication ...............................................................................................................................................54

3.3.1 No Authentication............................................................................................................................................. 55

3.3.2 Simple Password .............................................................................................................................................. 59

3.3.3 Local User ............................................................................................................................................................ 63

3.3.4 Voucher ................................................................................................................................................................ 71

3.3.5 SMS ........................................................................................................................................................................ 78

3.3.6 Facebook ............................................................................................................................................................. 83

3.3.7 External RADIUS Server ................................................................................................................................. 84

3.3.8 External Portal Server ..................................................................................................................................... 90

3.4 Free Authentication Policy ....................................................................................................................................91

3.5 MAC Filter ....................................................................................................................................................................92

3.6 Scheduler .....................................................................................................................................................................94

3.7 QoS .................................................................................................................................................................................96

3.8 Site Settings ...............................................................................................................................................................99

3.8.1 LED ......................................................................................................................................................................... 99

3.8.2 Device Account ............................................................................................................................................... 100

3.8.3 Reboot Schedule ............................................................................................................................................100

3.8.4 Log Settings .....................................................................................................................................................101

3.8.5 Batch Upgrade ................................................................................................................................................. 102

3.8.6 SSH ......................................................................................................................................................................104

3.8.7 Management VLAN ........................................................................................................................................ 105

4 Omada Cloud Service ............................................................................................. 106

4.1 Configure the Cloud Access .............................................................................................................................. 107

4.1.1 Enable Cloud Access ....................................................................................................................................107

4.1.2 Manage the Cloud Users .............................................................................................................................107

4.2 Manage the Controller via Omada Cloud ...................................................................................................... 109

4.2.1 Access the controller via Omada Cloud ................................................................................................110

4.2.2 Change your TP-Link ID information .......................................................................................................112

5 Configure the EAPs Separately .......................................................................... 113

5.1 View the Information of the EAP ....................................................................................................................... 114

5.1.1 Active Channel Information ........................................................................................................................114

5.1.2 Overview ............................................................................................................................................................115

5.1.3 LAN .......................................................................................................................................................................115

5.1.4 Radio .................................................................................................................................................................... 116

5.2 View Clients Connecting to the EAP ............................................................................................................... 116

5.2.1 User ...................................................................................................................................................................... 116

5.2.2 Guest ...................................................................................................................................................................117

5.3 View Mesh Information of the EAP .................................................................................................................. 117

5.3.1 Uplinks ................................................................................................................................................................117

5.3.2 Downlinks ..........................................................................................................................................................118

5.4 Configure the EAP ................................................................................................................................................. 118

5.4.1 Basic Config ......................................................................................................................................................118

5.4.2 IP Setting ............................................................................................................................................................119

5.4.3 Radio .................................................................................................................................................................... 120

5.4.4 Load Balance .................................................................................................................................................... 121

5.4.5 WLANs ................................................................................................................................................................122

5.4.6 LED .......................................................................................................................................................................122

5.4.7 Trunk Settings (Only for EAP330) ............................................................................................................. 123

5.4.8 Rogue APs Detection .................................................................................................................................... 123

5.4.9 Local LAN Port Settings (Only for EAP115-Wall and EAP225-Wall) ...........................................124

5.4.10 Forget this AP ................................................................................................................................................ 124

6 Manage the Omada Controller ............................................................................ 125

6.1 User Account ........................................................................................................................................................... 126

6.2 General Setting ....................................................................................................................................................... 127

6.2.1 Configure Controller Name .........................................................................................................................127

6.2.2 Configure Mail Server ...................................................................................................................................127

6.3 History Data Retention ......................................................................................................................................... 129

6.4 Backup&Restore..................................................................................................................................................... 130

6.5 Auto Backup ............................................................................................................................................................. 130

6.6 Migrate ....................................................................................................................................................................... 133

6.6.1 Controller Migrate ..........................................................................................................................................133

6.6.2 Site Migrate ....................................................................................................................................................... 137

6.7 Information About the Software ....................................................................................................................... 141

7 Application Example ............................................................................................... 142

7.1 Basic Configuration ............................................................................................................................................... 143

7.2 Advanced Settings ................................................................................................................................................ 143

7.2.1 Monitor the EAPs with Map ......................................................................................................................... 143

7.2.2 Configure Portal Authentication ...............................................................................................................144

7.2.3 Create a SSID for the Employees .............................................................................................................146

7.2.4 Configure Scheduler .....................................................................................................................................147

Appendix: Omada App .............................................................................................. 149

1 Install Omada App on the Mobile Device ...................................................................................................... 150

2 Manage your Network in Standalone Mode ................................................................................................. 150

3 Manage your Network in Controller Mode .................................................................................................... 153

3.1 Locally manage your EAPs using the Omada App ...........................................................................153

3.2 Remotely manage your EAPs using the Omada App ......................................................................156

1

Quick Start

Omada Controller is a management software for TP-Link EAPs. With this software, you can centrally

manage your EAPs, such as configure EAPs in batches and conduct real-time monitoring of EAPs

locally or remotely through Omada Cloud service.

Follow the steps below to complete the basic settings of Omada Controller.

1. Determine the Network Topology

2. Install Omada Controller Software

3. Inform the EAPs of the Controller Host's Address

4. Start and Log In to the Omada Controller

5. Create Sites and Adopt the EAPs

6. Monitor and Manage the EAPs

2

1.1 Determine the Network Topology

There are two methods to centrally manage EAPs via Omada Controller:

■

Management on the Local Network

■

Management via Cloud Access

Determine your management method according to your need and refer to the following

introductions to build your network topology.

Tips:

Omada app offers a convenient way to access the Omada Controller and adopt EAPs. With Local Access and

Cloud Access function on the Omada app, you can manage the controller at local and remote sites. For more

detailed information about Omada app, refer to

Appendix: Omada App

.

1.1.1 Management on the local Network

There are two kinds of network topologies to centrally manage EAPs on the local network:

■

Omada Controller and EAPs are in the same subnet.

■

Omada Controller and EAPs are in different subnets.

Determine your management method according to your need and refer to the following

introductions to build your network topology.

Management in the Same Subnet

If your Omada Controller and EAPs are in the same subnet, refer to the following network topology.

A router acts as a DHCP server to assign IP addresses to EAPs and clients. Omada Controller

should be installed on one host, which is called as Controller Host. The other hosts in the same

LAN can access the Controller Host to manage the network. Taking the following topology as an

example, you can enter “https://192.168.0.100:8043“ in a web browser on Host B to visit the Omada

Controller interface on Host A. It's recommended to set a static IP address to the Controller Host

for the convenient login to the Omada Controller interface.

3

Host B

IP: 192.168.0.200/24

Host A (Controller Host)

IP: 192.168.0.100/24

Layer 2 Switch

Internet

EAPs

Clients

Router (DHCP Server)

LAN IP:192.168.0.1/24

Omada Controller

Note:

• Omada Controller must be running all the time when you manage the network.

• Omada Controller can be running on only one host in a LAN. When other users in the LAN try to launch

Omada Controller on their own hosts, they will be redirected to the host that is already running Omada

Controller.

Management in Different Subnets

If your Omada Controller and EAPs are in different subnets, refer to the following topology.

A router acts as the gateway of the network. A layer 3 switch acts as a DHCP server to assign IP

addresses to EAPs and clients. The Controller Host and the EAPs are connected to the switch's

different network segments. To help EAPs find the Controller Host, Omada Discover Utility should

be installed on Host B which is in the same subnet with the EAPs. For how to use Omada Discovery

Utility, refer to Inform the EAPs of the Controller Host’s Address.

4

Host B

IP: 192.168.2.100/24

Layer 3 Switch

(DHCP Server)

LAN

WAN

EAPs

Clients

Router

Omada Controller

Omada

Discovery Utility

Internet

Host A (Controller Host)

IP: 192.168.1.100/24

192.168.1.0/24

192.168.2.0/24

1.1.2 Management via Cloud Access

With Cloud Access enabled on the Omada Controller, you can use https://omada.tplinkcloud.com to

remotely access and monitor multiple controllers. If you want to manage EAPs remotely via Omada

Cloud , refer to the following topology.

A router acts as the gateway of the network. A Layer 3 switch acts as a DHCP server to assign

IP addresses to EAPs and clients. The management device is not on the local network. On the

management device, you can launch a web browser to remotely launch Omada Controller to

manage EAPs via Omada Cloud. For more details about Cloud Access, refer to Omada Cloud

Service .

Switch

LAN

WAN

EAPs

Clients

Router

Omada Controller

Internet

Controller Host

Management Devices

5

1.2 Install Omada Controller Software

We provide Omada Controller for both Windows and Linux operating systems. Determine your

operation system and follow the introductions below to install Omada Controller.

1.2.1 Installation on Windows Host

Make sure your PC meets the following requirements of hardware and system, then properly install

the Omada Controller software.

Hardware Requirements

Omada Controller can manage up to 1500 EAPs if the Controller Host has enough hardware

resources. To guarantee operational stability for managing 1500 EAPs, we recommend that you use

the hardware which meets or exceeds the following specifications:

CPU: Intel Core i3-8100, i5-6500, or i7-4700 with 2 or more cores and 4 or more threads.

Memory: 6 GB RAM or more.

System Requirements

Operating System: Microsoft Windows 7/8/10/Server.

Web Browser: Mozilla Firefox 32 (or above), Google Chrome 37 (or above), Opera 24 (or above), or

Microsoft Internet Explorer 11 (or above).

Note:

We recommend that you deploy Omada Controller on a 64-bit operating system to guarantee the software

stability.

Install Omada Controller

Download the installation file of Omada Controller from the website

https://www.tp-link.com/

en/download/EAP-Controller.html

.

Then follow the instructions to properly install the Omada

Controller software. After successful installation, a shortcut icon

of the Omada Controller will be

created on your desktop.

1.2.2 Installation on Linux Host

Two versions of installation package are provided: .tar.gz file and .deb file. The .tar.gz file can be

used in multiple versions of Linux operating system. And the .deb file can be used in Ubuntu and

Debian.

Make sure your PC meets the following requirements of hardware and system, then choose the

proper installation files to install the Omada Controller software.

6

Hardware Requirements

Omada Controller can manage up to 1500 EAPs if the Controller Host has enough hardware

resources. To guarantee operational stability for managing 1500 EAPs, we recommend that you use

the hardware which meets or exceeds the following specifications:

CPU: Intel Core i3-8100, i5-6500, or i7-4700 with 2 or more cores and 4 or more threads.

Memory: 6 GB RAM or more.

System Requirements

Operating System: 64-bit Linux operating system, including Ubuntu 14.04/16.04/17.04, CentOS

6.x/7.x, Fedora 20 (or above) and Debian 9.8.

Web Browser: Mozilla Firefox 32 (or above), Google Chrome 37 (or above), Opera 24 (or above), or

Microsoft Internet Explorer 11 (or above).

Install the Omada Controller

Download the installation file of Omada Controller from our website

https://www.tp-link.com/en/

download/EAP-Controller.html.

Make sure you have jsvc and curl installed in your system before installation, which is vital to the

smooth running of the system. If your system does not have jsvc or curl installed, you can install it

manually with the command: apt-get install or yum install. For example, you can use the command:

apt-get install jsvc or yum install jsvc to get jsvc installed. And if dependencies are missing, you

can use the command: apt-get -f install to fix the problem.

■

Install the

.tar.gz file

Follow the steps below to install Omada Controller on your Linux PC:

1. Make sure your PC is running in root mode. You can use this command to enter root mode:

sudo

2. Extract the tar.gz file using the command:

tar zxvf Omada_Controller_v3.0.5_linux_x64_targz.tar.gz

3. Install Omada Controller using the command:

sudo./install.sh

■

Install the

.deb file

Follow the steps below to install Omada Controller on your Linux PC:

1. Make sure your PC is running in root mode. You can use this command to enter root mode:

7

sudo

2. Install the .deb file using the command:

dpkg -i Omada_Controller_v3.0.5_linux_x64.deb

Tips:

• For installing the .tar.gz, if you want Omada Controller to run as a user (it runs as root by default) you should

modify OMADA_USER value in bin/control.sh.

• To uninstall Omada Controller, go to the installation path: /opt/tplink/EAPController, and run the command:

sudo ./uninstall.sh.

• During uninstallation, you can choose whether to backup the database. The backup folder is /opt/tplink/

eap_db_backup.

• During installation, you will be asked whether to restore the database if there is any backup database in the

folder /opt/tplink/eap_db_backup.

1.3 Inform the EAPs of the Controller Host's Address

If your Controller Host and EAPs are in the same network segment, you can skip this section.

If your Controller Host and EAPs are in different subnets, you need to install Omada Discovery

Utility on a host that is in the same network segment with the EAPs. Omada Discovery Utility can

help EAPs find the Controller Host.

System Requirements

Windows 7/8/10/Server

Mac OS X 10.7/10.8/10.9/10.10/10.11

Install and Use Omada Discovery Utility

Follow the steps below to install Omada Discovery Utility and use it to inform the EAPs of the

Controller Host's IP address:

1. Download the installation file with the latest version from the website https://www.tp-link.com/

en/download/EAP-Controller.html#EAP_Discovery_Tool.

2. Make sure you have JRE (Java Runtime Environment) with version1.8 installed on your system

before installation. If your system loses JRE, download JRE from the website https://www.oracle.

com/technetwork/java/javase/downloads/jre8-downloads-2133155.html and install it on your

system.

3. For Windows OS, run the start-omada-discovery-utility.bat to open the Omada Discovery

Utility. For Mac OS, use the command java –jar ** to open the Omada Discovery Utility. Then the

following window will pop up. This window shows the information of all EAPs in the same LAN.

8

4. Click Manage in the Action column or select multiple EAPs and click Batch Setting.

5. Enter the hostname or IP address of the Controller Host.

6. Enter the EAP’s username and password (both are admin by default).

7. Click Apply to inform the EAP of the Controller Host's hostname or IP address. And then the

connection can be established between the EAP and the Controller Host.

1.4 Start and Log In to the Omada Controller

Launch Omada Controller and follow the instructions to complete the basic configurations, and

then you can log in to the management interface.

9

1.4.1 Launch Omada Controller

Double click the icon and the following window will pop up. You can click Hide to hide this window

but do not close it. After a while, your web browser will automatically open.

Note:

• If your browser does not open automatically, click Launch a Browser to Manage Wireless Network. You

can also launch a web browser and enter http://127.0.0.1:8088 in the address bar.

• If your web browser opens but prompts a problem with the website's security certificate, click Continue.

• Only one Omada Controller can run in a LAN. If an Omada Controller has already been running on a host

that is in your LAN, you will be redirected to the Omada Controller interface on that host.

1.4.2 Do the Basic Configurations

In the web browser you can see the configuration page. Follow the setup wizard to complete the

basic settings for Omada Controller.

1. Click Let’s Get Started.

2. Specify a name for Omada Controller. Click Next.

10

3. Specify a username and password for the login account. Specify the email address for resetting

your password in case that you forget the password. After logging in Omada Controller, set a

mail server so that you can receive emails and reset your password. For how to set a mail server,

refer to Configure Mail Server. Click Next.

4. The setup page displays all the detected EAPs in the network. Select one or more EAPs to be

managed and click Next.

11

5. Set an SSID name (wireless network name) and password for the EAPs to be managed. Omada

Controller will create two wireless networks, a 2.4GHz one and a 5GHz one, both encrypted in

WPA2-PSK mode. Click Next.

6. If you want to manage EAPs via Omada Cloud, enable the Cloud Access button, and bind your

TP-Link ID to your Omada Controller, and then click Next. If you want to manage EAPs on the

local network, you can just click Skip. For more details about Omada Cloud, please refer to

Omada Cloud Service in chapter 4.

12

7. Review your settings and click Finish.

1.4.3 Log In to the Management Interface

Once the basic configurations are finished, the browser will be redirected to the following page.

Log in to the management interface using the username and password you have set in the basic

configurations.

13

Note:

In addition to the Controller Host, other hosts in the same LAN can also manage EAPs via remote access to the

Controller Host. For example, if the IP address of the Controller Host is 192.168.0.100 and Omada Controller is

running normally on this host, you can enter https://192.168.0.100:8043/login, or https://192.168.0.100:8043,

or http://192.168.0.100:8088 in the web browser of other hosts in the same LAN to log in to the Omada

Controller and manage EAPs. Or you can log in to Omada Controller on the management devices through

Omada Cloud service.

1.5 Create Sites and Adopt EAPs

Omada Controller can manage multiple EAP networks, which are called sites. Multiple sites are

logically separated, and each site has its own configurations. There is an initial site named Default.

The Default site cannot be deleted. If you have no need to manage EAPs with different sites, you

can edit the default site and skip the Create Sites section. However, Adopt the EAPs is a necessary

step to manage the EAPs.

1.5.1 Create Sites

There are three methods to create sites: Add Sites, Import Sites, and Copy Sites. Determine the

method according to your need and refer to the following introductions to create sites.

Add Sites

Follow the steps below to add a new site directly.

1. Click

in the top left corner of the page and select , and then the following

window will pop up.

14

2. Click and enter a unique name for the new site.

3. Click Apply to create the site.

Import Sites

You can import the site from another controller. The site settings and EAPs in the site will be

imported to the new site.

Note:

• The site to be imported must come from a different controller.

• Importing sites is available only for local logged-in users.

1. Click in the top left corner of the page and select , and then the following

window will pop up.

2. Click and enter a unique name for the new site.

3. Click Browse to upload the backup file of other site and click Import to import the site.

Page is loading ...

TP-LINK EAP110 User manual

TP-LINK EAP110 User manual

Related papers

Other documents