Page is loading ...
1
Assembly Instructions
Item# S-DN096
ASSEMBLY INSTRUCTIONS
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start
to finish.
DO NOT assemble this item alone for your safety. Two people are necessary for smooth &
safe installation.
Item identification: For ease of identification, all parts are labeled to correspond to the step
number in which the part is used.
IMPORTANT:
1. Keep all children and pets away from assembly area. Children and pets should be
supervised while product is being assembled.
2. The assembled product should be located at least 6 feet (2 m) from any obstruction such as
fence, garage, house, overhanging branches, laundry lines or electrical wires.
3. This unit is heavy. Do not assemble this item alone. 2 people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only.
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for installation and use of this product. Some special procedures may be valid
in your area.
2
Parts list
No.
DESC.
Qty
A
Chair back
2
B
Seat
2
C1
Left leg
2
C2
Right leg
2
D1
Left arm
2
D2
Right arm
2
E
Front connector
2
F
Connector
4
G
Wood dowel
4
AA
Bolt M4*35
8
BB
Bolt M6*50
8
CC
Bolt M6*50
4
DD
Bolt M6*50
8
EE
Flat washer M6
12
FF
Nut M6
12
GG
Steel plug
8
HH
Wrench
1
Step 1:
Connect front connector (E) and left leg / right leg
(C1/C2) with bolts (AA) and screwdriver (not
included). Don’t tighten the bolts at this stage.
Step 2:
Insert wood dowels (G) into the holes of left leg / right
leg (C1/C2); connect seat (B) to left leg / right leg
(C1/C2) with bolt (BB), flat washer (FF), nuts (FF), as
shown. Use screwdriver (not included) and wrench
(HH); don’t tighten the bolts and nuts at this stage.
Chair Assembly
3
No assembly is needed for the table; simply open the
table as shown below.
Step 3:
Firstly, insert Steel plugs (GG) into the hole of chair back
(A), then, connect connector (F) and chair back (A) by
with bolts (DD), flat washers (EE), nuts (FF) and
screwdriver (not included) and wrench (HH), don’t
tighten them in this step.
Step 4:
Firstly, insert Steel plugs (GG) into the hole of chair back
(A), and then, connect chair back (A) and left leg / right leg
(D1/D2) by with bolts (DD), flat washer (EE) and
screwdriver (not included) as Fig 1, don’t tighten bolts.
Connect left arm / right arm (D1/D2) and left leg / right leg
(C1/C2) by with bolts (CC), flat washers (EE), nuts (FF)
and screwdriver (not included) and wrench (HH) as Fig 2.
Last, tighten all bolts.
4
WARRANTY
(1-year warranty on structure)
Thank you for purchasing this Sunjoy product. These products have been made to demanding,
high-quality standards and are guaranteed for domestic use against manufacturing faults. This
warranty does not affect your statutory rights.
In case of any malfunction of your Sunjoy product (failure, missing part, etc.), please contact
one of our service technicians at our toll-free service line at 1-866-578-6569 from 8 AM to 4:30
PM, Monday to Friday, Eastern time. The manufacturer reserves the right to repair or replace
the defective product, at its discretion.
The product is guaranteed if used for normal trade purposes. Any warranty is invalid if the
product has been overloaded or subject to neglect, improper use or an attempted repair other
than by an authorized agent. Heavy-duty or daily professional/commercial usage are not
guaranteed. Due to continuous product improvement, we reserve the right to change the
product specifications without prior notice.
Made in China
/
