Defiant SE-0172R User manual

Brand: Defiant

Model: SE-0172R

Type: User manual

ALARM (SIREN)

Slide the switch to . Press the button on the remote. The main unit’s red LED ashes

with a beep, and continue ashing every 5 seconds indicating the unit is armed.

Once the unit detects an intrusion within its monitored area, the alarm goes

off for 20 seconds.

ALARM (SIREN & STROBE )

Slide the switch to . Press button on the remote, the main unit’s red LED ashes

once with a beep, and continue ashing every 5 seconds indicating the unit is armed.

Once the unit detects an intrusion within its monitored area, the alarm goes off for

20 seconds accompanied with the white ashing LED light.

LIGHT ONLY

Slide the switch to . Press the button on the remote. The main unit’s red LED ashes

once with a beep, and continue ashing every 5 seconds indicating the unit enters

light only mode.

When the light in the room becomes dim, a bright white LED turns on for 10 seconds

if motion within its monitored area is detected. (Note: The LED light stays on continuously

if it detects motion continuously.)

CHIME

Slide the switch to . Press button on the remote, the main unit’s red LED ash once with

a beep, and continue ashing every 5 seconds indicating the unit enters chime mode.

When motion within its monitored area is detected, chime sounds off.

THANK YOU

purchase of this motion-sensing alarm with remote. We strive to continually create quality

products designed to enhance your home. Visit us online to see our full line of products

available for your home improvement needs. Thank you for choosing Deant!

USE AND CARE GUIDE

MOTION- SENSING ALARM WITH REMOTE

Safety Information

Package Contents

WARNING: Prolonged exposure to pitching alarm

sound may cause permanent hearing loss.

IMPORTANT:

Do not expose to rain.

Install the product at least 3 ft. from the oor for

optimum performance.

This alarm contains small parts and is not suitable

for children.

Periodically check the condition of the batteries.

Warranty

This product is guaranteed to be free of defects in materials and workmanship for 1 year

from the date of purchase. If this product is defective, call 888-697-2389 for repair

or replacement parts or return the product to the store from which it was purchased.

Guarantee does not include normal wear and tear, bulbs or batteries.

Any battery may rupture or explode if put in a re or otherwise exposed to excessive

heat. TO AVOID RISK OF INJURY, DO NOT EXPOSE BATTERIES TO EXCESSIVE HEAT. To

reduce the risk of personal injury or harm to your alarm, take the following precautions:

Do not use different types of batteries in the same alarm.

When replacing batteries always replace the whole set.

Do not use rechargeable or reusable batteries.

Do not allow children to install batteries unsupervised.

Follow battery manufacturer’s instructions as to proper

handling, storage and disposal of batteries.

Questions, problems, missing parts? Before returning to the store,

call Deant Customer Service

M-F 9am-6pm PST

1-888-697-2389

HOMEDEPOT.COM

Troubleshooting

Warning

Problem Solution

The Main Unit beeps once at 10

second intervals.

Battery power is low, replace promptly.

The main unit alarm sound becomes

low, or LED light becoms dim.

Remote distance becomes obviously

shorter than average.

Replace with new batteries.

Item #1001-223-096

Model #SE-0172R

Deant

Product Description

Installation

Operating Instructions (Continued)

Alarm (siren)

Alarm (siren with strobe)

Light only

Chime

INSTANT Alarm triggers immediately

OFF

DELAY

Power off

Alarm triggers after 7 seconds

IN STA NT

OF F

DE LAY

IN STANT

OF F

DE LAY

Symbol Description

Main Unit

Remote

Bracket

Screws

Part Description

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Statement

Push down the bracket and remove from the main unit.

Mount the bracket with two screws (included inside battery compartment) on the wall.

Hang the main unit onto the bracket; pull it up until it clicks into its position.

Loosen the screw on the bracket hinge and adjust the main unit to a proper

position, then tighten the screw.

Operating Instructions

Battery Installation

Main Unit:

Set the switch to OFF and slide down the battery cover on the back.

Follow the polarity instructions to insert three x AA Alkaline batteries (not included).

Put the battery cover back on.

Or insert an optional DC 5V adaptor (not included) into the power jack.

Remote:

Unscrew the back cover to insert or replace one fresh CR2032 battery.

Follow the polarity instructions.

Press the button, and the red LED turns on if the battery is installed correctly.

Operation

Slide the Main Unit to INSTANT or DELAY to power on. The red LED ashes for 30 seconds.

Remove the main unit from the bracket, and press the code matching button once on the

back of the main unit, a beep sounds off. Then press the button on the remote within 5

seconds after pressing the code matching button. Three beeps sound off. This indicates the

code has been successfully programmed.

Up to ve remotes can be programmed to the main unit.

NOTE:

Press the button on the remote to turn off the unit and stop the alarm/chime

sound, or light any time, with 2 beeps and ashing red LED light.

Or sliding to OFF to power off the unit.

NOTE: Press the code matching button continuously for 3 seconds to clear all

the memorized code, three beeps sounds off.

WARNING: Any battery may leak harmful chemicals which may damage skin,

clothing or the inside of the alarm. TO AVOID RISK OF INJURY, DO NOT LET ANY

MATERIAL LEAKED FROM A BATTERY COME IN CONTACT WITH EYES OR SKIN.

Defiant SE-0172R User manual

Defiant SE-0172R User manual

Defiant SE-0172R User manual

Related papers

Other documents