American Standard 0614000.222 Specification

0614000.222
American Standard
Brand
American Standard
Model
0614000.222
Type
Specification
J3
© 2020 AS America Inc.
Studio
®
Under Counter Sinks
❏ 0614.000 Unglazed Rim
❏ 0614.300 Glazed underside
• Rectangular under counter mount sinks
• Made from vitreous china
• Unglazed rim
• Front overow
• Supplied with mounting kit and template
Nominal Dimensions:
19-3/4" x 13-3/4"
(502 x 350mm)
Bowl size:
18" (457mm) wide
12" (305mm) front to back
6-7/16" (164mm) deep
❏ 0618.000 Unglazed Rim
Nominal Dimensions:
23-5/8" x 16-5/8"
(600 x 422mm)
Bowl size:
21-1/16" (535mm) wide
14" (356mm) front to back
6-1/4" (159mm) deep
Compliance Certications - Meets or Exceeds the Following Specications:
• ASME A112.19.2M for Vitreous China Fixtures
• CAN/CSA B45 series
Studio
®
Under Counter Sinks
VITREOUS CHINA
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
spec_0614_StudioUnderctrSinks_Rev4 2/20
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
BARRIER FREE
MEETS THE AMERICANS WITH DISABILITIES A
CT GUIDELINES
AND ICC ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor.
Lavatory installed 102mm (4") minimum from front edge
of countertop provides 686mm (27") knee clearance area.
J4
© 2020 AS America Inc.
Studio
®
Under Counter Sinks
VITREOUS CHINA
spec_0614_StudioUnderctrSinks_Rev4 2/20
51mm
(2") MIN.
83mm
(3-1/4")
FINISHED WALL
OR SPLASHBACK
C
EDGE OF
COUNTER
TOP CUTOUT
A
B
22mm
(7/8")
E
F
SINK
RIM
13mm
(1/2") MIN.
REFER TO INSTRUCTIONS PROVIDED
WITH KIT FOR ADDITIONAL INFORMATION
CLIP
MACH.
SCREW
1-1/4" O.D.
TAILPIECE
1-1/4" O.D.
WASTE
203mm
(8")
38mm
(1-1/2")
330mm
(13")
273mm
(10-3/4")
13mm
(1/2)
D
SUPPLIES
AS REQ'D.
ADA DRAIN
OUTLET
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
864mm
(34")
*
279mm
(11")
*
*
*
FINISHED FLOOR
22mm
(7/8")
FITTING
CENTER-SET
SPREAD
A
1-1/16" (27mm)
1-1/4" (32mm)
B
4" (102mm)
8" (203mm)
G
H
MODEL
0614
0618
E
502mm
(19-3/4")
600mm
(23-5/8")
F
350mm
(13-3/4")
422mm
(16-5/8")
G
457mm
(18")
535mm
(21-1/16")
H
305mm
(12")
356mm
(14")
864mm
(34")
102mm
(4")
D
216mm
(8-1/2")
209mm
(8-1/4")
C
96mm
(3-3/4")
108mm
(4-1/4")
610mm
(24")
152mm
(6")
MAX.
BARRIER FREE
CLEARANCE
686mm
(27")
MIN.
203mm
(8")
MIN.
229mm
(9")
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
NOTES:
INSTALL PRODUCT ACCORDING TO THE INSTALLATION INSTRUCTIONS. COUNTERTOP
MANUFACTURER OR CUTTER MUST USE CUTOUT TEMPLATE PROVIDED WITH
PRODUCT OR A CURRENT ONE PROVIDED BY AMERICAN STANDARD. AMERICAN
STANDARD IS NOT RESPONSIBLE FOR CUTOUT ERRORS WHEN THE INCORRECT
TEMPLATE IS USED.
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIED AND “P" TRAP ARE SUGGESTED.
▼ UNDERCOUNTER MOUNTING KIT SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances
established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for
use of superseded or voided pages.
BARRIER FREE
  • Page 1 1
  • Page 2 2

American Standard 0614000.222 Specification

0614000.222
American Standard
Brand
American Standard
Model
0614000.222
Type
Specification
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents