ISSYZONEPOS IPDA030 User manual

Brand: ISSYZONEPOS

Model: IPDA030

Type: User manual

This manual is also suitable for

IPDA030/IPDA031

Portable Data Terminal

Quick Start Guide

www.issyzonepos.com

- 1 -

Overview

- 2 -

Removing & Installing battery

1. Firstly, put the left and right battery cover buckles down to the right position.

2. Make use of the flip-up (on the right side) space between the battery hatch

and the bottom shell to pull the battery cover out.

3. Firstly, insert the bottom of the battery into the plughole of the inside Battery

bunker, and then press the top of the battery.

- 3 -

Install TF/SIM card

1. Please choose the corresponding card slot to insert SIM card according to

the view.

(Note: the hand-hold terminal only supports Micro SIM card. The standard

SIM card slot is used to install the encrypted PSAM card.)

- 4 -

Device Charging

The device has two kinds of charging methods for option:

a: Put the right waterproof USB stopple out to insert into the USB cable

through the USB cable carried by the device.

b: Charge the device through the seating-type charger (needing to purchase it

separately).

Introduction on the seating-type charger charging:

1. The seating-type charger can put in one device and one battery at the same

time.

2. The left indicator light is an indicator light for the device charging and will

turn into red after power up. Note that it will not show the charging state and

please examine the led indicator light when the device is charging.

3. The right indicator light is an indicator light for battery charging, will turn into

red when charging and green when the battery has got a full charge.

- 5 -

Scanning Function

If your device is equipped with the scanning function of codes, please follow

the following instruction to use:

1. Please find the icon of scanning codes (Pic 1) and open it.

2. In the scanning and testing interface of Pic 2, please press Scan and then

scan the code.

- 6 -

NFC Function

If your PDA with NFC function, please operate it as below:

1. Please find the NFC APP (Pic 1) and open it.

2. In NFC testing interfaces in Pic 2, Pls read the card by NFC reading area.

(Note: NFC has the optional function. Please ensure your device has that

function, then you can use it.)

- 7 -

LF125K Function

If your PDA with LF function, please operate it as below:

1. Please find the icon of NFC (Pic 1) in the program listing (Pic 1) and open it.

2. In LF testing interface in Pic 2, Please read the card by LF reading area.

(Note: the reading-card function with low-frequency 125K has the optional

function. Please ensure your device has that function, then you can use it.)

- 8 -

UHF Function

If your PDA with UHF function, please operate it as below:

1. Please find the UHF APP (Pic 1) and open it.

2. In UHF testing interface in Pic 2, Please close the card to the inductive zone

and read it.

(Note: the reading-card function of UHF has the optional function. Please

ensure your device has that function, then you can use it.)

- 9 -

Function of fingerprint identification

If your PDA with fingerprint identification function, please operate it as below:

1. Please find the fingerprint icon (Pic 1) and open it.

2. In fingerprint testing interface in Pic 2, fingerprints can be collected and

identified.

(Note: fingerprint identification has the optional function. Please ensure your

device has that function, then you can use it.)

- 10 -

Thermal printing Function

If you PDA has Printing function, please operate it as below:

1. Please find Portable Printing icon (Pic 1) and open it.

2. In the printing and testing interface of Pic 2, you can test the printing

functions.

(Note: printing has the the optional function. Please ensure your device has

that function, then you can use it.)

- 11 -

OTA(online update)

Our PDA supports OTA(update online) function,you can update the elatest

firmware by OTA. Please operate it as bellow:

1. Please enter into “Setting”--”About phone”.

2. Click the “Additional system updates” (Pic 1) and enter into the updating

firmware interfaces.

3. Click the “Check now”(Pic 2) to update the OS.

- 12 -

FAQs

1. How can you do it if the device fails to start up?

(1) When pressing Power needing 3-4 seconds, the screen of the device just

start to show up. Please wait for the screen to display contents, then you can

loosen Power.

(2) Secondly, try to check up whether the battery of the device has power or

not. Put the battery into the device and connect to the USB data cable. If its

screen displays the icon that its battery is charging, indicating lack of battery

power.

2. Why does the computer fail to link with the device?

If the device inserts into the USB interface of the computer, without any

indication, please replace a USB interface to test it again. If there is no any

response, please replace a computer.

3. The device shows lights, but why doesn’t the code be scanned?

This situation generally is the problems on the scanning setting-up. Please

firstly check up the output ticked of the keyboard, needing everyone to enter

into the scanning device. If ticked, please reset the scanning engine, and then

turn the scanning switch off and on once.

4. How can the battery be used correctly?

The batteries of the device are polymer batteries. Please charge the battery in

time if it run out of power. You cannot store it in a long time in a case of the

battery without power or with full power; It’s better to store it when it has the

power of 50 percent; If it’s not suitable for the device, please take the battery

out from the device and store it.

ISSYZONEPOS IPDA030 User manual

Brand: ISSYZONEPOS

Model: IPDA030

Type: User manual

This manual is also suitable for

Download PDF

report

ISSYZONEPOS IPDA030 User manual

This manual is also suitable for

ISSYZONEPOS IPDA030 User manual

Other documents