Toro Height of Cut Latching Kit, Grandstand Mowers Installation guide

Brand: Toro

Model: Height of Cut Latching Kit, Grandstand Mowers

Type: Installation guide

FormNo.3421-500RevB

HeightofCutLatchingKit

Grandstand

Mowers

ModelNo.138-4890

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal131-3521

131-3521

1.Heightofcut

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3421-500*B

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheexistingplates.

Latchplate1

Shoulderbolt

Washer-headshoulderbolt1

Washer2

Nut(3/8inch)

Nut(1/4inch)

Wearplug1

Installthelatchplate.

Spacer(1.7inches)

Spacer(2.7inches)

Innerplate1

Spacer(0.7inch)

Outerplate

Washer3

Bolt(3/8x3-3/4inches)

Nut(3/8inch)

Pin1

Installthenewplates.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.DisengagethePTO,engagetheparkingbrake,

andmovethemotion-controlleversoutwardto

theNEUTRAL-LOCKposition.

3.Shutofftheengineandremovethekey.

RemovingtheExisting

Plates

NoPartsRequired

Procedure

1.Removethefueltank;refertotheOperator’s

Manualforthemachine.

2.Usetheheight-of-cutlevertolowerthemower

deckontowoodblocks.

3.Removebothplatesandfastenersasshownin

Figure1.

g246899

Figure1

1.Nut(3/8inch)

5.Innerplate

2.Spacer—2.6inches6.Outerplate

3.Spacer—1.4inches(2)7.Bolt—3/4x3-1/2inches

(3)

4.Spacer—1inch(2)

InstallingtheLatchPlate

Partsneededforthisprocedure:

1Latchplate

Shoulderbolt

1Washer-headshoulderbolt

2Washer

Nut(3/8inch)

Nut(1/4inch)

1Wearplug

Procedure

1.Removethelatchfromtheheight-of-cutlever

(Figure2).

g246977

Figure2

1.Shoulderbolt

4.Washer

2.Washer-headshoulder

bolt

5.Nut(3/8inch)

3.Latch

6.Nut(1/4)

2.Cutoutthetemplateattheendofthispublication

andalignitonthelever(Figure3).

g255884

Figure3

1.Drillthehole(3/8inch)

here.

2.Template

3.Drillahole(3/8inch)intotheleveratthelocation

showninFigure3.

4.Installthenewlatchplateusing1shoulderbolt,

1washer-headshoulderbolt,2washers,1nut

(3/8inch),1nut(1/4inch)asshowninFigure4.

Note:Ensurethatthewashersseatontothe

shoulderoftheboltandarenotpinchedbetween

theheight-of-cutliftarmandtheshoulderofthe

bolt.

g246976

Figure4

1.Shoulderbolt5.Nut(3/8inch)

2.Latch6.Wearplug

3.Latch-releaserod7.Washer

4.Nut(1/4)

8.Washer-headshoulder

bolt

5.Torquetheshoulderboltto1017to1243N∙cm

(90to110in-lb)andtorquethewasher-head

shoulderboltto41to49N∙m(30to36ft-lb).

6.Installthewearplugintothelever(Figure4).

InstallingtheNewPlates

Partsneededforthisprocedure:

Spacer(1.7inches)

Spacer(2.7inches)

1Innerplate

Spacer(0.7inch)

Outerplate

3Washer

Bolt(3/8x3-3/4inches)

Nut(3/8inch)

1Pin

Procedure

1.Installtheinnerandouterplatestothemachine

usingthespacers,washers,bolts,andnutsas

showninFigure5.

2.Installthepinintheholeforyourdesiredheight

ofcut.

g247029

Figure5

1.Innerplate

6.Outerplate

2.Spacer—0.7inch(2)7.Spacer—2.7inches

3.Washer(3)8.Spacer—1.7inches(2)

4.Bolt—3/8x3-3/4inches

(3)

9.Nut—3/8inch(3)

5.Pin

Notes:

g255885

Toro Height of Cut Latching Kit, Grandstand Mowers Installation guide

Toro Height of Cut Latching Kit, Grandstand Mowers Installation guide

Toro Height of Cut Latching Kit, Grandstand Mowers Installation guide

Related papers

Other documents