CMP 27515-154 Operating instructions

CMP
Brand
CMP
Model
27515-154
Category
Above ground pool accessories
Type
Operating instructions
R
MULTI-PORT VALVE
USER MANUAL
CMP# 27515-154-000
PRODUCT INFORMATION
This multi-port valve is for replacement of the
Hayward SP0714T Vari-Flo XL Valve* and it is used for
Hayward Sand Filters such as S166T, S180T, S210T,
S220T and S244T. It features an easy-to-use lever
action handle that lets you dial up to seven valve/
lter functions: lter, backwash, waste, rinse, closed,
winterize or recirculate. The ports are 1.5 FPT ttings.
Important Notice: This manual contains important
information about the installation, operation and safety
procedures of the product. Read and follow all instructions
before the installation or servicing. Failure to follow safety
warnings and instructions can result in severe injury,
death, or property damage.
!
CAUTION: TURN PUMP OFF BEFORE SERVICING OR CHANGING VALVE POSITIONS
!
FILTER PUMP►TOP►THROUGH FILTER ►BOTTOM►POOL RETURN
For normal lter action and vacuuming pool through lter.
BACKWASH PUMP►BOTTOM►THROUGH FILTER►TOP►WASTE
For cleaning lter by reversing ow.
RINSE PUMP►TOP►THROUGH FILTER►BOTTOM►WASTE
For start-up cleaning and resetting lter bed after backwashing.
WASTE PUMP►WASTE
For vacuuming directly to waste, lowering pool level or draining pool.
CLOSED NO FLOW. DO NOT USE WHEN PUMP IS IN OPERATION
For shutting off all ow to lter and pool.
RECIRCULATE PUMP►POOL RETURN
For circulating water without going through lter.
WINTER DRAIN WATER FROM VALVE
For winterizing.
Valve Setting Water Flow Path; Setting Function
*Haywrd is a registered trademark of Hayward Industries
INSTALLATION & SERVICE INSTRUCTIONS
• Conrm correct valve is being used for your lter type and model.
• To install valve to lter, clamp valve on top of lter and connect pump, return, and waste lines by following
the markings of the ports. Use Teon pipe tape for connect pipe ttings. DO NOT OVER TIGHTEN PIPE
FITTINGS.
• VALVE TOP IS UNDER SPRING LOAD. To open top half and service valve, evenly and alternately loosen cover
screws.
• To disassemble valve and replace parts, set handle in the position between any two settings. Tap out handle
pin and remove cover screws.
• To re-assemble the top half, ensure bottom gasket and diverter sealing surface are clean. Place diverter on
a smooth and rm surface. Assemble parts on shaft by following Figure A. Make sure the pointer on handle
and the arrow on diverter point to same direction. Press down on the cover using clamps to depress the
heavy-duty spring and secure the valve handle with the pin.
• To re-assemble the top half to valve bottom, tighten cover screws evenly and alternately. DO NOT OVER-
TIGHTEN THE SCREWS, OR USE MOTORIZED SCREWDRIVERS.
• WINTERIZATION: To winterize, drain the pump and lter per manufacturer’s instructions. Press down on the
valve handle and rotate to the WINTER position.
1Handle 1
2Dowel Pin 1
3Plastic Washer 1
4Top Cover 1
5O-ring 1
6Washer 2
7Heavy Duty Spring 1
8Diverter O-ring 2
9Diverter 1
Item QTYItem Description
Figure A: Top Half Assy Components
0313 sb
For the full list of replacement parts of this unit, please check our catalog or our website at www.c-m-p.com.
CUSTOM MOLDED PRODUCTS, INC | 800-733-9060 | NEWNAN, GEORGIA 30265 | WWW.C-M-P.COM
1
2
3
4
6
7
6
8
9
5
Complete Top Half Assy
27506-200-100
(Includes 1-9)
IF O-RINGS REQUIRE LUBRICATION, USE ONLY SILICONE TYPE LUBRICANTS
!
Complete Top Half Assy
27506-200-100
(includes 1-9)
  • Page 1 1
  • Page 2 2

CMP 27515-154 Operating instructions

CMP
Brand
CMP
Model
27515-154
Category
Above ground pool accessories
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents