St. Bernard iPrism 3000 User manual

Brand
St. Bernard
Model
iPrism 3000
Type
User manual
The iPrism Model 3000 System
Page 1
Hardware Reference
Figure 1. Model 3000 Front Panel (with cover open)
•On/Off Switch: When power is not applied to the system, press this switch to power the iPrism.
When power is on you should use the Appliance Manager to shut down your system. If it is not
possible, then pressing this switch once will tell the iPrism to perform an orderly shut down after
which it will power down the iPrism. If the system does not shut down after about five minutes,
holding the power switch for 5 seconds will power down the iPrism instantly, although this may
result in the loss of the last few minutes of logging data.
•Reset Switch: Press once to preform a reset of the iPrism. This switch should be used as a last
resort. The preferred method to reset your iPrism is to start the Appliance Manager, go to the
Exit section and select the Reboot option.
•POWER LED: This LED indicator illuminates when power is applied to the system.
•HDD LED: Indicates disk activity.
Page 2
On/Off Switch Reset Switch
HDD LEDPOWER LED
Figure 2. Model 3000 Rear Panel
•Power Connector: This connects power to iPrism (115 – 230 VAC auto-sensing).
•Power Isolation Switch: This switch isolates the power supply from the incoming power. This
is a “hard” power switch. The one on the front of the Model 3000 is a “soft” power switch. This
switch should be left in the on position except just before disconnecting the power cord from the
iPrism. Powering the system on and off should be done through the front switch.
•Console Port: This is a RS232 DB9 serial connector, which may be used with the console cable
to connect to another computer in order to perform troubleshooting or low level management on
the system. This port should only be used under the direction of the iPrism technical support
staff. (Note: The console port is the bottom DB9 serial connector. The top one is not used.)
•Management Ethernet Connector: This RJ45 connector provides a third auto-sensing 10/100
Mbps Ethernet port that can be used for out-of-band management of the iPrism. (This is used for
advanced configurations only. See the Administrator’s Manual, Chapter 2, Section: Using the
Management Interface for information.)
•Internal Ethernet Connector: This RJ45 connector provides auto-sensing Ethernet connectivity
to your internal network (the network iPrism will apply filtering to).
•External Ethernet Connector: This RJ45 connector provides auto-sensing Ethernet connectivity
to the external network (Internet).
Page 3
External Ethernet
Connection
Internal
Ethernet
Connection
Management
Ethernet
Connection
Console Port
Power
Isolation
Switch
Not Used
Power Connector
Installing the System
1. If you are installing the iPrism in a rack, attach the brackets from the enclosed rack mounting kit
to the iPrism and mount it in a standard rack.
2. If you are installing the iPrism on a shelf or desktop, place it on the shelf and make sure that all
of the ventilation holes on the side and back of the unit are clear.
3. Connect the power cable. Turn on the power isolation switch. Do not power the system on using
the front power switch at this time.
4. Connect a network cable from the Internal Ethernet Port of the iPrism to your internal
network.
5. Leave the External Ethernet Port unconnected. (Later in the installation process, this may be
connected to your firewall or Internet connection. See the iPrism Installation Guide for
information on how and when to connect this port.)
6. Leave the Management Ethernet Port unconnected.
7. Follow the instructions in the iPrism Installation Guide for information on how to complete the
installation process and configure your iPrism system.
Page 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

St. Bernard iPrism 3000 User manual

Brand
St. Bernard
Model
iPrism 3000
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents