AAXA AAXA P300 Neo Smart User manual

aaxa

TECHNOLOGIES

User Guide

Caution!

WARNING: Please use this product as instructed. Misuse may cause

injury or death.

DO NOT use while driving.

DO NOT expose to water or wet

surfaces. Electric shock may occur.

DO NOT expose the projected LED

image to your eyes or the eyes of

others.

DO NOT block or restrict airow

from ventilation holes as this may

cause the projector to overheat.

Keep the projector and charger away from

any heat sources.

Caution for Headphone Use

• Prolonged use at high volume may

impair your hearing.

• High volume during walking or driving

may cause distractions and result in

injury or death.

Table of Contents

Chapter 1: At a Glance

P300 Neo-S Introduction

Remote & Touchpad

Accessories

Chapter 2: Getting Started

Focus Adjustment / Throw Distance

Navigating the Main Menu

Connecting to WiFi

Connecting to a BT device

Loading External Content

Chapter 3: Menu Screens

Videos Menu

Photos Menu

Connecting via Digital Input

Connecting via VGA

Connecting to Composite Video

Browser

Streaming Applications

Apps

Smartphone Mirroring

Ofce

Chapter 4: Settings Menu

Brightness Settings

WiFi Settings

Advanced Settings

Language

Display Settings

Bluetooth Settings

Backup & Reset

About

Chapter 5: Technical Details

Troubleshooting

Specications

Notes

1

2

4

5

6

7

8

10

13

17

21

23

26

28

30

31

33

34

37

41

42

43

44

45

46

47

48

49

50

52

53

P300 Neo-S at a Glance

Chapter 1

Digital Input

USB Port

Main Unit Front/Back

AV Port

Headphone Out

Power Port

1

Focus Adjustment

Touchpad

TF Card Slot

Mini-VGA Port

On/Off Switch

Remote & Touchpad

2

NOTE: Pressing power on the remote while it is on will put your projector in standby mode. In

order to fully turn the projector off

, the On/Off switch must be in the “Off” position.

Remote

Power On/Off

Select Source

Main Menu

Navigation

Media Player

Menu Navigation

Volume Up

Volume Down

Keystone Adjustment Keystone Adjustment

Remote & Touchpad Cont.

The P300 Neo-S incorporates a capacitive touchpad directly onto the top of the projector. This

touchpad works in conjunction with a pointer and allows users to select icons, APKs, and scroll

through the menu system. The touchpad can be used in conjunction with the “Back” and “Vol-

ume” buttons below the touchpad.

3

Please note that the P300 Neo-S allows for 2-nger scrolling. In order to scroll up, use 2 n-

gers on the touchpad and swipe up. In order to scrool down, use 2 ngers on the touchpad

and swipe down.

The P300 Neo-S allows 2-nger touch as a substitute for the “Back” button.

Accessories

4

*Under various circumstances, the actual accessories may be different from

those shown in the pictures above.

Additional accessories are available for purchase at www.aaxatech.com

Remote

Power Adapter

A/V Cable

Tripod

Getting Started

1. Connect the power cord to the P300 Neo-S.

2. Connect the other end of the power cord into the wall power source.

3. Move the On/Off swtich to the “On” position. Your projector should start up.

5

Powering ON the projector

Chapter 2

Powering OFF the projector

1. To turn off the projector, use the power button on the remote or the On/Off switch.

Using the On/Off switch will fully turn off the projector.

1. The P300 Neo-S needs to be plugged in and charged for four to ve hours before

operation. Please ensure the On/Off switch is in the “Off” position during this time

Plugging In the projector

Connecting to WiFi

1. View page 8 for details.

Connecting to a Bluetooth Device

1. View page 10 for details.

Focus Adjustment / Throw Distance

6

DIAGONAL SCREEN SIZE

16:9 Aspect Ratio

Throw Distance

Unit: Inches

20

30

40

50

60

70

80

90

Diagonal Size

Unit: Inches

13

20

27

33

40

47

53

60

• Spin the focus wheel left or right until the image becomes

clear.

Focus Adjustment

Throw Distance Chart

Throw Ratio 1.5

*minimum throw distance: 15 inches

Navigating the Main Menu

7

Main Menu

The Main Menu allows access to all the features of the P300 Neo Smart Projector.

Main Menu Features

• Videos - View videos from external devices such as TF card and USB

• Photos - View photos from external devices such as TF card and USB

• Browser - Brings up a browser

• Streaming - Brings up Youtube, Netix, Hulu, Twitch, HBO Go and Amazon Prime Video

• Apps - Brings up all apps that are already preinstalled or downloaded

• Mirroring - Bring up app to mirror your phone screen on the projector screen

• Settings - Brings up Application Manager, Network Settings, Bluetooth Settings, Language

Settings, Backup&Reset, Projector Settings, etc

• Ofce- View les from external devices such as TF card and USB

• Digital Input- Brings up

connection via Digital Input

• VGA - Brings up connec-

tiong via VGA

• Video-RCA - Brings up

connection via A/V

Inputs

Connecting to WiFi

8

Please see next page for steps to establish to a WiFi connection.

Connecting to WiFi:

• Select the “Settings” icon (Fig. 2.1).

• Select the “Network Settings” option and navigate to your WiFi network and

click on it to connect.

• A window will appear and ask for a password, please type it in. When nished,

press “Connect” and the projector will connect to your WiFi (Fig. 2.2).

Fig. 2.1

Fig. 2.2

Connecting to WiFi FAQ

9

Connecting to WiFi:

The P300 Neo-S features a WiFi chipset capable of 802.11 b/g/n connection.

This means it is compatible with most WiFi routers. To connect to a WiFi router,

follow the following steps:

Step 1: Access the Network Settings Submenu: Settings -> Network

Settings

Step 2: Turn WiFi radio to “On” by highlighting and toggling the WiFi

Button under WiFi settings

Step 3: Select the appropriate Router

Step 4: Enter the router password in the password selection (by

pressing “OK”). It is recommended that the automatic IP

address acquisition be turned on

Troubleshooting

1. Unable to connect

a. Check Security Settings – WPA/WPA2 PSK

b. Check if Router is in range

Connecting to a Bluetooth Device

10

Please see next page for steps to connect to a Bluetooth device

Connecting to Bluetooth:

• Select the “Settings” icon (Fig. 2.8).

• Select the “Bluetooth Settings” option and navigate to your Bluetooth Device

and click on it to connect (Fig. 2.9).

• The projector features a Bluetooth radio. The Bluetooth radio is designed to

connect Bluetooth enabled device, typically a Bluetooth mouse or speaker.

The projector supports one Bluetooth device at a time.

Fig. 2.8

Fig. 2.9

Bluetooth Speaker or Mouse

11

To connect a Bluetooth Speaker or Mouse

Step 1: Access the Bluetooth Menu (Settings Bluetooth)

Step 2: Turn on Bluetooth functionality

Step 3: Turn on your Bluetooth device and enable discovery. This varies

with each device. Some devices require the power switch to be turned

“ON”. Other devices have a Bluetooth icon that is pressed to make the

device “discoverable”

Step 4: If your device does not pop up automatically, click on the three

vertical dots at the top of the page and click “Refresh”

Step 5: Highlight your device and click “OK” to connect. Your device

should show “connecting.” If a PIN is asked, try 0000 or 1234 – these

are the standard PIN codes. If this does not work, check with your

device manufacturer for the PIN

Troubleshooting

12

• Disconnecting. It takes 10-15 seconds for a BT device to connect or discon-

nect from the system. Failure to wait for this time could result in an improper

connection. Check to ensure device is connected in the BT submenu.

• If the Bluetooth device does not automatically reconnect please go to the

Bluetooth settings and press on the device to reconnnect to it.

• If the device still does not reconnect please press on the icon on the right of

the device’s name to unpair the device and pair it again.

Loading External Content

13

The P300 Neo-S can read les directly

from both a TF Card and USB Drive.

Supported le types include:

MP3 / WMA / OGG / WAV

AVI / JPG / GIF/ BMP / TXT / PPT /

DOC / XLS/ PDF

(up to 32 GB)

Loading External Content Cont.

14

(up to 32 GB)

How to insert your TF Card

• Slide in your TF card into the TF card

slot on the side of the P300 Neo-S (as

shown in picture).

• Gently slide the TF card until it clicks

into place.

Loading External Content Cont.

How to insert your USB Drive

• Slide your USB Drive into the USB port.

• Gently slide the drive until it cannot go in any further.

(up to 32 GB)

15

16

Loading External Content Cont.

Photos & Videos Menu

• Videos and Photos can be played by clicking “Photos & Video”

on the Main Menu.

Files Menu

• All les can be shown by clicking “Files” on the Main Menu.

OfceMenu

• .pdf, .docx, .xls, .ppt, .txt can be shown by clicking “Ofce” on the

Main Menu.

Once your TF Card or USB Drive is inserted into the projector, the TF Card

or USB Drive Storage will be loaded automatically and the content can be

found through:

• To view videos, access the content via the “Photos & Videos” icon or the

“Files” icon (Fig 3.1).

• All sources will be displayed. Select the source and choose the video you

want to view (Fig 3.2).

17

Fig. 3.1

Fig. 3.2

Menu Screens

Chapter 3

Video Menu

Page is loading ...

AAXA AAXA P300 Neo Smart, P300 Neo, P300 Neo Smart, P300 Neo Smart Pico Projector User manual

Related papers

Other documents