ATEN EC1000 User manual

Brand: ATEN

Model: EC1000

Category: Networking

Type: User manual

NRGence™ Energy Box

EC1000

User Manual

www.aten.com

EC1000 User Manual

FCC, CE Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT. This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

This device complies with Part 15 of the Fcc Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Warning: Operation of this equipment in a residential environment could

cause radio interference.

RoHS

This product is RoHS compliant.

EC1000 User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual are subject

to change without prior notification by the manufacturer. The manufacturer makes no

representations or warranties, either expressed or implied, with respect to the contents

hereof and specifically disclaims any warranties as to merchantability or fitness for any

particular purpose. Any of the manufacturer's software described in this manual is sold

or licensed as is. Should the programs prove defective following their purchase, the

buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of

all necessary servicing, repair and any incidental or consequential damages resulting

from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV interference

caused by unauthorized modifications to this device. It is the responsibility of the user

to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation of this

system if the correct operational voltage setting was not selected prior to operation.

PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.

If any bodily injury or property damage with respect to operation of the product results

from users not having installed the product in accordance with the instructions provided

in the product’s user manual, or the product is used in an environment with a current

load over the designed specifications of the product, ATEN is not liable for any loss or

damage.

International http://support.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

EC1000 User Manual

Package Contents

The EC1000 package consists of:

1 EC1000 Energy Box

1 Power Adapter

1 Mounting Kit

4RJ-45 Cables

1 CD ROM (Manual, eco Sensors Software)

1 User Instructions*

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the EC1000 installation.

* Features may have been added to the EC1000 since this manual was

published. Please visit our website to download the most up-to-date version.

Manual Date: 2020-02-18

All other brand names and trademarks are the registered property of their respective owners.

EC1000 User Manual

Contents

FCC, CE Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Sensor Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

EC1000 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

EC1000 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 2.

Hardware Setup

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Rack Mounting - Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Rack Mounting - Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rack Mounting - Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Securing the Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 3.

Front Panel Operation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Front Panel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 4.

Browser Operation

Operation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

eco Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Browser Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

The EC1000 Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

EC1000 User Manual

Page Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Browser Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

First Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Changing the Administrator Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Energy Sensor Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Monitor Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Administrator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

The System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Notification Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Device Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Service Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

IPv4 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Working Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Session Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Account Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Authentication & Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SNMP & Telnet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SNMPv3 Account Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SNMPv1/v2c Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Event Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

SMTP Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

SNMP Trap Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Syslog Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Firmware File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Backup/Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

EC1000 User Manual

vii

Chapter 5.

Telnet Commands

Remote Terminal Operations - Telnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Read Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Switch Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Read Power Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Read Environmental Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Close Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

EC1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

IP Address Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Method 1:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Method 2:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Method 3:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

EC1000 User Manual

viii

About This Manual

This User Manual is provided to help you get the most from your EC1000

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the EC1000 System. Its

purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation, and explains some basic operation procedures.

Chapter 3, Front Panel Operation, explains how to operate the EC1000

from the local console.

Chapter 4, Browser Operation, describes how to login to the EC1000

with a browser, and explains the functions of the icons and buttons that appear

on the opening page, and explains the administrative procedures that are

employed to configure the EC1000’s working environment.

Chapter 5, Telnet Commands, describes how to connect to the EC1000

and the available Telnet commands.

An Appendix, at the end of the manual provides technical and

troubleshooting information.

EC1000 User Manual

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

 Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

 Numbered lists represent procedures with sequential steps.

 Bullet lists provide information, but do not involve sequential

steps.

 Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start



Run means

to open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

EC1000 User Manual

This Page Intentionally Left Blank

Chapter 1

Introduction

Overview

The EC1000 Energy Box solution is the latest evolution of ATEN’s energy

intelligence product line NRGence™. The EC1000 monitors the electrical

current of 4 Energy PDU's, along with room temperature, humidity, and

differential pressure using environmental sensors. The Energy Box provides

instant real-time power management and energy-saving control for data

centers– allowing you to upgrade and maintain your current IT power

resources quickly and cost-effectively.

The EC1000 Energy Box has four RJ-45 ports to connect to four Energy PDUs

and four RJ-11 ports to connect external sensors to monitor environmental

conditions. Each environmental sensor can provide measured readings of

temperature, humidity, and differential pressure from separate areas of a room,

giving you a wide range of monitoring and protection.

The EC1000 features real-time status, system logs, threshold alerts, and event

notification. The Energy Box logs power and environmental conditions

according to customizable minimum/maximum thresholds set for; current,

temperature, humidity, and differential pressure.

The Energy Box allows the power and environmental data to be monitored by

display at the rack or remotely for easy viewing and maintenance. The Energy

Box is a standalone unit with over IP monitoring that is controlled by a built-

in web GUI or ATEN's eco Sensors software.

Remote monitoring offers secure access with 128bits SSL encryption, and

customizable account policies for user management. Remote authentication

supports RADIUS and additional management interfaces including HTTP,

HTTPS, and SNMPv1&v2&v3 (Read, Write, Trap). Event notifications can be

monitored via Syslog/SMTP/SNMP trap and by audible alarm for real-time

local and remote alerting.

The NRGence™ EC1000 Energy Box is the intelligent cost effective solution

to monitor ATEN's Energy PDUs – to ensure safe and effective energy-saving

power management.

EC1000 User Manual

Features

Operation

 Space saving 1U and 0U rack mounting with front, rear, and side mounting

 4 RJ-45 Energy Sensor Ports to monitor four Energy PDUs (0A to 32A per

port) electrical currents

 4 RJ-11 Environmental Sensor Ports to monitor temperature, humidity,

and differential pressure*

 Maximum Amperage Monitor 32A@100V~240V (Energy Box)

 3 digit 7 segment front panel LED displays current/sensor/IP address

information

 Threshold monitoring for:

 Current

 Temperature*

 Humidity*

 Differential pressure*

 Threshold alerting through:

 Local: audible alarm and LED lights

 Remote: SMTP/SNMP trap/Syslog

Management

 Front panel LED indicators for current, temperature*, humidity*,

differential pressure*, and IP address at the Energy Box

 Remote real-time current, temperature*, humidity*, and differential

pressure* monitoring and management

 Management through eco Sensors Energy Management Software or 3rd

party SNMP manager

 Supports name assignment for individual Energy PDUs

 Multi-language GUI supports: English, Traditional Chinese, Simplified

Chinese, Japanese, Korean, German, Italian, Spanish, Portuguese, French,

Russian

 Event Logging – 128 line event log

 Syslog support

 F/W upgradable

Chapter 1. Introduction

Remote Access

 Remote management via TCP/IP using built in 10/100Mbps Ethernet port

 Management via built in browser based GUI

 Network Interfaces: TCP/IP, UDP, HTTP, HTTPS, SSL, SMTP, DHCP,

NTP, DNS, 10Base-T/100Base-TX, auto sense, Ping

 Supports SNMP Manager V1, V2, V3

Security

 Strong security features include password protection and advanced

encryption technologies – utilizing 128 bit SSL

 RADIUS authorization and authentication

*Requires external sensors (see Optional Accessories, page 5).

EC1000 User Manual

Requirements

 Energy PDU PE1216, PE1324, PE2220, or PE2340

 Environmental Sensors EA1140, EA1240, EA1340 to monitor

environmental data

 One Cat 5e Ethernet cable to connect the EC1000 to the local area network

 Browsers accessing the EC1000 must support SSL 128 bit encryption.

Chapter 1. Introduction

Optional Accessories

Sensors

Sensors are optional accessories. You can use the EC1000 Energy Box without

sensors. However, if you want to have complete energy management of your

data center with the full use of the EC1000 Energy Box, you would need to use

eco Sensors software and install 4 sensors for each of the racks to generate

more complete energy-efficient data and charts. Sensors help you maintain a

safe and highly efficient data center by monitoring environmental conditions.

Higher sensor density installations help to generate more accurate and precise

data. Available sensors are show in the table, below:

Sensor Management

Sensors can be managed via the EC1000’s browser based graphical user

interface (GUI) or with NRGence™ eco Sensors software that can be

downloaded from the ATEN website. The download link can be found on the

software CD provided with the EC1000 package.

Sensor Part Number

Temperature EA1140

Temperature / Humidity EA1240

Differential Pressure / Temperature EA1340

EC1000 User Manual

Components

EC1000 Front View

No. Component Description

1 Readout Section



The first single-digit LED indicates the port selected:



Energy Sensor (1-4)



Environmental Sensor (1-4)



IP Address (1)



The second 3-digit LED displays information related to

the first LED:



Current



Temperature, Humidity, Differential Pressure



IP Address

2 Energy and

Environmental Sensor

LEDs

Lights (Orange) for connected Energy Sensors and

(Green) for Environmental Sensors, currently connected

to a port and taking readings.

3 Selection LED Lights (Green) to indicate the selection (Energy,

Environment, IP) that the Readout is currently displaying.

4 Select Button Press the Select button to cycle through the selections

(Energy, Environment, IP) to display their data readout

on the 3-digit LED.

5 Reset Switch This switch must be pushed with a thin object, such as

the end of a paper clip.



Press and release to reboot the device.



Press and hold for more then three seconds to

reset the Energy Box to its factory default settings

6 Power LED Lights (Green) when the Energy Box is powered up and

ready to operate.

Chapter 1. Introduction

EC1000 Rear View

*External sensors are sold separately (see Optional Accessories, page 5).

No. Component Description

1 Grounding Terminal The wire used to ground the Energy Box attaches here.

2 Energy Sensor Ports The four RJ-45 cables that connect the Energy Box to

your Energy PDUs, plug in here.

3 Environmental Sensor

Ports

External sensors plug into these four RJ-11 ports.*

4 Power Jack The power adapter cable plugs into this jack.

5 LAN Port The cable that connects the Energy Box to the LAN

plugs in here.

EC1000 User Manual

This Page Intentionally Left Blank

Chapter 2

Hardware Setup

Rack Mounting

The EC1000 can be mounted in a 19” (1U) rack or in an 0U configuration

mounted to the side of the rack. To rack mount the device, use the rack

mounting brackets that came with your device. The brackets are screwed to the

front, rear or middle sides of the device, depending on the installation type and

then the unit can slide into the front of the rack, or mount to the side of the rack,

as shown in the diagrams below:

Rack Mounting - Front

1. Use 3 M3 x 8 Phillips hex head screws supplied with the rack mounting kit

to screw the rack mounting brackets into the sides near the front of the

unit.

2. Position the unit in the front of the rack and align the holes in the mounting

brackets with the holes in the rack.

1. Important safety information regarding the placement of this

device is provided on page 63. Please review it before proceeding.

EC1000 User Manual

3. Screw the mounting brackets to the rack.

Page is loading ...

ATEN EC1000 User manual

Brand: ATEN

Model: EC1000

Category: Networking

Type: User manual

Download PDF

report

ATEN EC1000 User manual

ATEN EC1000 User manual

Related papers

Other documents