Toyota Tundra Owner's manual

Category
Remote starters
Type
Owner's manual

Toyota Tundra's Remote Keyless Entry (RKE) system with RS3000 ECU lets you operate your vehicle's locks and alarm from a distance. It can be programmed to work with up to 4 remotes. To program a new remote, turn the ignition on, hold the ECU's programming switch for 3 seconds, then press a button on the remote within 5 seconds. The system will confirm with a chirp and flash of the lights.

Toyota Tundra's Remote Keyless Entry (RKE) system with RS3000 ECU lets you operate your vehicle's locks and alarm from a distance. It can be programmed to work with up to 4 remotes. To program a new remote, turn the ignition on, hold the ECU's programming switch for 3 seconds, then press a button on the remote within 5 seconds. The system will confirm with a chirp and flash of the lights.

Page 1
REMOTE CONTROL PROGRAMMING
The RS3000 ECU of the 2002 MY Tundra Remote Keyless Entry (RKE) System can be
To program (add) a REMOTE CONTROL to the system
:
1) Insert the key into the ignition switch, and turn it to “ON”.
2) Press and hold the ECU’s
PROGRAMMING SWITCH for 3 seconds.
–YOU MUST PERFORM THE NEXT STEP WITHIN 5 SECONDS–
3) Press and release a REMOTE CONTROL’s top or bottom button.*
The PIEZO “CHIRPER”
chirps once.
The exterior lights flash once.
5)
In
NOTE: The factory preset operation is for the top button on both
REMOTE CONTROLS
to
operate the
system; the bottom button is not programmed. To prevent accidental
erasure of a REMOTE CONTROLs code, we recommend that you program all of
REMOTE CONTROLS at the same time.
* Either button on the REMOTE CONTROL can be programmed to operate the RKE.
Press and Hold
For 3 Seconds
Press Once
4) Turn off the ignition. The ECU will now operate with the REMOTE CONTROL just programmed.
case
the RKE
ECU replaced,
the valet
mode function of the replacement
must
ECU
be
programmed
to
"ON" mode. (See "To activate VALET MODE")
programmed to be operated by as many as 4 REMOTE CONTROLS. To add or delete a
REMOTE CONTROL, you must connect the ignition switch connector of the Remote Keyless
Entry wire harness to the vehicle's ignition switch and access the RS3000 (RKE) ECU to
program the remote controls. Ignition switch connection is also required when replacing the
RKE ECU. See "2002 Tundra RS3000 Plus" installation instructions to connect the ignition
switch connector (Page 6) and to locate the RKE ECU.
original
RKE
the
is
PROGRAMMING
•TUNDRA•
REMOTE CONTROL PROGRAMMING
To erase all REMOTE CONTROL codes from the system:
1) Insert key into the ignition switch, and turn it to ON.
2) Press and hold the ECUs PROGRAMMING SWITCH for 3 seconds.
YOU MUST PERFORM THE NEXT STEP WITHIN 5 SECONDS
3) Press and hold the ECUs PROGRAMMING SWITCH for over 2 seconds again
.
The PIEZO CHIRPER chirps 3 times, and the exterior lights flash 3 times.
4) Turn off the ignition. The ECU has cleared all REMOTE CONTROL codes; until another
REMOTE CONTROL is programmed, the system will not work with any REMOTE CONTROL.
Press and Hold
For 3 Seconds
Press and Hold Again,
For 2 Seconds
1
2
Page 2
Page 3
REMOTE CONTROL PROGRAMMING
To activate VALET MODE (disable security functions)
1) Insert the key into the ignition switch, and turn it to ON
(
not ACC).
2) Using 1 REMOTE CONTROL, press and hold both
buttons (at the same time) for over 2
seconds.
YOU MUST PERFORM THE NEXT STEPS WITHIN 30 SECONDS
3) Select the operating mode. (Follow this procedure as written, regardless of the current mode.)
* If you do not turn the ignition key to LOCK, or
exceed 30 seconds during the programming
steps,
the previous operation mode will remain
unchanged.
Mode Programming Step Programming Completion
VALET MODE
Press and release the top
Turn the ignition switch to
ON
REMOTE CONTROL BUTTON the LOCK* position.
(No Security
three times. (The PIEZO CHIRPER chirps
Functions)
(The PIEZO CHIRPER chirps three times, and the exterior
once, and the exterior lights lights flash 3 times.)
flash once for .6 second.)
Turn to ON
or START
Press Both Buttons
NOTE: This procedure is not necessary if the vehicle is equipped with RS3000 Plus
security system.
PROGRAMMING
•TUNDRA•
  • Page 1 1
  • Page 2 2
  • Page 3 3

Toyota Tundra Owner's manual

Category
Remote starters
Type
Owner's manual

Toyota Tundra's Remote Keyless Entry (RKE) system with RS3000 ECU lets you operate your vehicle's locks and alarm from a distance. It can be programmed to work with up to 4 remotes. To program a new remote, turn the ignition on, hold the ECU's programming switch for 3 seconds, then press a button on the remote within 5 seconds. The system will confirm with a chirp and flash of the lights.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI