Genius GEO 13 Operating instructions

GEO 13

ISTRUZIONI PER L’USO - INSTRUCTIONS FOR USE

INSTRUCTIONS POUR L’USAGER - INSTRUCCIONES PARA EL USO

GEBRAUCHSANLEITUNG - GIDS VOOR DE GEBRUIKER

ITALIANO

AVVERTENZE PER L’INSTALLATORE

OBBLIGHI GENERALI PER LA SICUREZZA

ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente

tutta l’istruzione. Una errata installazione o un errato uso del prodotto può

portare a gravi danni alle persone.

Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.

I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati alla

portata dei bambini in quanto potenziali fonti di pericolo.

Conservare le istruzioni per riferimenti futuri.

Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in

questa documentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe

pregiudicare l’integrità del prodotto e/o rappresentare fonte di pericolo.

GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da

quello per cui l’automatismo è destinato.

Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi

infiammabili costituisce un grave pericolo per la sicurezza.

Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito

dalle Norme EN 12604 e EN 12605.

Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di

sicurezza adeguato, devono essere seguite le Norme sopra riportate.

GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costru-

zione delle chiusure da motorizzare, nonché delle deformazioni che dovessero

intervenire nell’utilizzo.

L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN

12445. Il livello di sicurezza dell’automazione deve essere C+D.

Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elettrica

e scollegare le batterie.

Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare

con distanza d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile l’uso

di un magnetotermico da 6A con interruzione onnipolare.

Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia

da 0,03 A.

Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti

metalliche della chiusura.

L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita

da un controllo di coppia. E’ comunque necessario verificarne la sogli di intervento

secondo quanto previsto dalle Norme indicate al punto 10.

I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali

aree di pericolo da Rischi meccanici di movimento, come ad Es. schiacciamento,

convogliamento, cesoiamento.

Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa nonché

di un cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso, oltre

ai dispositivi citati al punto “16”.

GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento

dell’automazione, in caso vengano utilizzati componenti dell’impianto non di

produzione GENIUS.

Per la manutenzione utilizzare esclusivamente parti originali GENIUS.

Non eseguire alcuna modifica sui componenti facenti parte del sistema d’au-

tomazione.

L’installatore deve fornire tutte le informazioni relative al funzionamento manuale

del sistema in caso di emergenza e consegnare all’Utente utilizzatore dell’impianto

il libretto d’avvertenze allegato al prodotto.

Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto

durante il funzionamento.

L’applicazione non può essere utilizzata da bambini, da persone con ridotte ca-

pacità fisiche, mentali, sensoriali o da persone prive di esperienza o del necessario

addestramento.

Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di impul-

so, per evitare che l’automazione possa essere azionata involontariamente.

Il transito tra le ante deve avvenire solo a cancello completamente aperto.

L’utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’intervento

e deve rivolgersi solo ed esclusivamente a personale qualificato GENIUS o centri

d’assistenza GENIUS.

Tutto quello che non è previsto espressamente in queste istruzioni non è permesso.

ENGLISH

IMPORTANT NOTICE FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

ATTENTION! To ensure the safety of people, it is important that you read all the

following instructions. Incorrect installation or incorrect use of the product

could cause serious harm to people.

Carefully read the instructions before beginning to install the product.

Do not leave packing materials (plastic, polystyrene, etc.) within reach of children

as such materials are potential sources of danger.

Store these instructions for future reference.

This product was designed and built strictly for the use indicated in this documen-

tation. Any other use, not expressly indicated here, could compromise the good

condition/operation of the product and/or be a source of danger.

GENIUS declines all liability caused by improper use or use other than that for which

the automated system was intended.

Do not install the equipment in an explosive atmosphere: the presence of inflam-

mable gas or fumes is a serious danger to safety.

The mechanical parts must conform to the provisions of Standards EN 12604 and

EN 12605.

For non-EU countries, to obtain an adequate level of safety, the Standards mentioned

above must be observed, in addition to national legal regulations.

GENIUS is not responsible for failure to observe Good Technique in the construction

of the closing elements to be motorised, or for any deformation that may occur

during use.

The installation must conform to Standards EN 12453 and EN 12445. The safety level

of the automated system must be C+D.

Before attempting any job on the system, cut out electrical power and disconnect

the batteries.

The mains power supply of the automated system must be fitted with an all-pole

switch with contact opening distance of 3mm or greater. Use of a 6A thermal breaker

with all-pole circuit break is recommended.

Make sure that a differential switch with threshold of 0.03 A is fitted upstream of

the system.

Make sure that the earthing system is perfectly constructed, and connect metal

parts of the means of the closure to it.

The automated system is supplied with an intrinsic anti-crushing safety device

consisting of a torque control. Nevertheless, its tripping threshold must be checked

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

as specified in the Standards indicated at point 10.

The safety devices (EN 12978 standard) protect any danger areas against mecha-

nical movement Risks, such as crushing, dragging, and shearing.

Use of at least one indicator-light is recommended for every system, as well as a

warning sign adequately secured to the frame structure, in addition to the devices

mentioned at point “16”.

GENIUS declines all liability as concerns safety and efficient operation of the automa-

ted system, if system components not produced by GENIUS are used.

For maintenance, strictly use original parts by GENIUS.

Do not in any way modify the components of the automated system.

The installer shall supply all information concerning manual operation of the system

in case of an emergency, and shall hand over to the user the warnings handbook

supplied with the product.

Do not allow children or adults to stay near the product while it is operating.

The application cannot be used by children, by people with reduced physical, men-

tal, sensorial capacity, or by people without experience or the necessary training.

Keep remote controls or other pulse generators away from children, to prevent the

automated system from being activated involuntarily.

Transit through the leaves is allowed only when the gate is fully open.

The User must not in any way attempt to repair or to take direct action and must

solely contact qualified GENIUS personnel or GENIUS service centres.

Anything not expressly specified in these instructions is not permitted.

FRANÇAIS

CONSIGNES POUR L’INSTALLATEUR

RÈGLES DE SÉCURITÉ

ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la

lettre toutes les instructions. Une installation erronée ou un usage erroné

du produit peut entraîner de graves conséquences pour les personnes.

Lire attentivement les instructions avant d’installer le produit.

Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent pas

être laissés à la portée des enfants car ils constituent des sources potentielles

de danger.

Conserver les instructions pour les références futures.

Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans cette

documentation. Toute autre utilisation non expressément indiquée pourrait compro-

mettre l’intégrité du produit et/ou représenter une source de danger.

GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent de

celui auquel l’automatisme est destiné.

Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz ou de

fumées inflammables constitue un grave danger pour la sécurité.

Les composants mécaniques doivent répondre aux prescriptions des Normes EN

12604 et EN 12605.

Pour les Pays extra-CEE, l’obtention d’un niveau de sécurité approprié exige non

seulement le respect des normes nationales, mais également le respect des Normes

susmentionnées.

GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la con-

struction des fermetures à motoriser, ni des déformations qui pourraient intervenir

lors de l’utilisation.

L’installation doit être effectuée conformément aux Normes EN 12453 et EN 12445.

Le niveau de sécurité de l’automatisme doit être C+D.

Couper l’alimentation électrique et déconnecter la batterie avant toute interven-

tion sur l’installation.

Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur omnipolaire

avec une distance d’ouverture des contacts égale ou supérieure à 3 mm. On recom-

mande d’utiliser un magnétothermique de 6A avec interruption omnipolaire.

Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec un

seuil de 0,03 A.

Vérifier que la mise à terre est réalisée selon les règles de l’art et y connecter les

pièces métalliques de la fermeture.

L’automatisme dispose d’une sécurité intrinsèque anti-écrasement, formée d’un

contrôle du couple. Il est toutefois nécessaire d’en vérifier le seuil d’intervention

suivant les prescriptions des Normes indiquées au point 10.

Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones

éventuellement dangereuses contre les Risques mécaniques du mouvement, comme

l’écrasement, l’acheminement, le cisaillement.

On recommande que toute installation soit doté au moins d’une signalisation lumi-

neuse, d’un panneau de signalisation fixé, de manière appropriée, sur la structure

de la fermeture, ainsi que des dispositifs cités au point “16”.

GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement

de l’automatisme si les composants utilisés dans l’installation n’appartiennent pas

à la production GENIUS.

Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.

Ne jamais modifier les composants faisant partie du système d’automatisme.

L’installateur doit fournir toutes les informations relatives au fonctionnement manuel

du système en cas d’urgence et remettre à l’Usager qui utilise l’installation les

“Instructions pour l’Usager” fournies avec le produit.

Interdire aux enfants ou aux tiers de stationner près du produit durant le fonc-

tionnement.

Ne pas permettre aux enfants, aux personennes ayant des capacités physiques,

mentales et sensorielles limitées ou dépourvues de l’expérience ou de la formation

nécessaires d’utiliser l’application en question.

Eloigner de la portée des enfants les radiocommandes ou tout autre générateur

d’impulsions, pour éviter tout actionnement involontaire de l’automatisme.

Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complète-

ment ouvert.

L’utilisateur doit s’abstenir de toute tentative de réparation ou d’intervention et

doit s’adresser uniquement et exclusivement au personnel qualifié GENIUS ou aux

centres d’assistance GENIUS.

Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.

ESPAÑOL

ADVERTENCIAS PARA EL INSTALADOR

REGLAS GENERALES PARA LA SEGURIDAD

ATENCION! Es sumamente importante para la seguridad de las personas seguir

atentamente las presentes instrucciones. Una instalación incorrecta o un

uso impropio del producto puede causar graves daños a las personas.

Lean detenidamente las instrucciones antes de instalar el producto.

Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al alcance

de los niños, ya que constituyen fuentes potenciales de peligro.

Guarden las instrucciones para futuras consultas.

Este producto ha sido proyectado y fabricado exclusivamente para la utilización

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

1.

2.

3.

4.

Page is loading ...

GEO 13

ENGLISH

Guide for the installer

Pagina 6

Notes on reading the instruction

Read this installation manual to the full before you begin installing the product.

The symbol

indicates notes that are important for the safety of persons and for the good condition of the automated

system.

The symbol draws your attention to the notes on the characteristics and operation of the product.

CE DECLARATION OF CONFORMITY

Manufacturer: GENIUS S.p.A.

Address: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY

Declares that: Control unit mod. GEO 13

conforms to the essential safety requirements of the following EEC directives:

2006/95/EC Low Voltage directive.

2004/108/EC Electromagnetic Compatibility directive.

Additional information:

This product underwent a test in a typical uniform configuration (all products manufactured by GENIUS S.p.A.).

Grassobbio, July 1, 2010

Managing Director

D. Gianantoni

•

INDEX

1. DESCRIPTION page.7

2. TECHNICAL SPECIFICATIONS page.7

3. PREPARATIONS page.7

4. . BOARD LAY-OUT (Fig. 1) page.7

5. DESCRIPTION OF CONNECTIONS AND OPERATION page.7

5.1. TERMINAL BOARD M1 (Fig. 2) page.7

5.2. TERMINAL BOARD M2 (Fig. 3) page.8

5.3. RAPID CONNECTOR M3 page.8

5.4. TERMINAL BOARD M5 (Fig. 5) page.8

6. ADJUSTING THE WORK TIME page.9

7. SETTING THE DIP-SWITCHES page.9

8. CONTROL LEDs page.10

9. PROTECTIVE FUSES page.10

10. FUNCTION LOGICS page.10

GEO 13

ENGLISH

Guide for the installer

Pagina 7

1. DESCRIPTION

Thank you for choosing our product. GENIUS is sure you will get the performances you expect to satisfy your requirements. All

our products are the result of a many years’ experience in the field of the automated systems, strengthened by being part of

a world leading group in this sector.

The GEO 13 control board is a microprocessor unit and was developed to control shutter gearmotors. It performs all control

functions for the gearmotor and the connected safety peripheral units during the shutter opening and closing operations.

Easy installation and programming of the control unit enables reduced installation times of the product. The main operating

parameters as well as the operating modes are set through dip-switches, whereas the work time is set by means of an

adjustment trimmer.

2. TECHNICAL SPECIFICATIONS

Supply voltage 230 V~ 50/60 Hz

Absorbed power 7 W

Motor max. load 1300 W

Max. load for accessories 500 mA

Operating ambient temperature -20°C to 50°C

Protective fuses 2 (power supply and accessories)

Function logics Step-by-step / Automatic

Work time (Opening / Closing) Min. 8 seconds max. 90 seconds, trimmer-adjustable

Pause time 7 pause times, can be selected through dip-switches

Terminal board inputs Mains power supply / Open / Stop / Obstacle detection

Rapid connector 5-pin connector for receiver card

Terminal board outputs Motor power supply / Flashing lamp power supply / Accessory power supply

Enclosure dimensions 80 x 150 x 195 mm

Protection class of enclosure IP54

3. PREPARATIONS

To ensure people’s safety, all warnings and instructions in this booklet must be carefully observed.

Incorrect installation or incorrect use of the product could cause serious harm to people.

Store these instructions for future references.

Make sure that an adequate differential switch is installed upstream of the system as specified by current safety standards.

On the power supply mains install a thermal breaker with omnipolar switching.

Make sure that an adequate earthing system is available.

To lay cables, use adequate rigid and/or flexible tubes.

Always separate the 230 V~ power cables from low voltage connection cables, using separate sheaths to avoid possible

interference.

4. . BOARD LAY-OUT (Fig. 1)

Pos. Description Pos. Description

M1

Terminal board for motor power supply and

flashing lamp

FSW Obstacle detection devices input signalling LED

M2

Terminal board for inputs and accessory power

supply

Power Mains power LED

M3 Rapid connector for receiver card Time Work Work time signalling LED

M5 Terminal board for mains power supply TR1 Work time adjustment trimmer

Stop Stop input signalling LED F1 Power supply protective fuse

Open Open input signalling LED RV1 Accessory protective fuse (self-resetting)

5. DESCRIPTION OF CONNECTIONS AND OPERATION

5.1. TERMINAL BOARD M1 (Fig. 2)

5.1.1. FLASHING LAMP

Terminals "LAMP & LAMP". 230V~ output. Connect, to these terminals, the power cable of the flashing lamp. Use a flashing lamp

with intermittent light since the flashing is not controlled by the control unit.

The maximum load on these terminals must not exceed 15W

5.1.2. MOTOR

•

GEO 13

ENGLISH

Guide for the installer

Pagina 8

Terminals "CL, COM & OP". 230V~ output. Connect, to these terminals, the power cables of the motor. Refer to the table below

for the connection sequence:

Terminal Contact Wire colour

CL Closing Brown

COM Common Blue / Grey

OP Opening Black

The colour of the wires connected to terminals OP & CL can be reversed according to the rotation direction of the

motor.

The maximum load on these terminals must not exceed 1300 W. The application of higher loads can damage the condition

of the control unit.

5.2. TERMINAL BOARD M2 (Fig. 3)

5.2.1. STOP

Terminals "STOP & COM". Normally closed contact. Connect, to these terminals, any pulse generator which, by opening the

contact, causes the immediate stop of the automated system thus disabling the automatic re-closure, if set. After the activation of

this command, send an OPEN command to resume normal operation. The status of this input is signalled by the “STOP” LED.

If no STOP commands are used, jumper connect this input. The “STOP” LED must be always ON.

Several pulse generators connected to these terminals must be connected in series.

5.2.2. OPEN

Normally open contact. Connect, to these terminals, any pulse generator which, by closing the contact, commands an opening

or closing movement of the shutter. The status of this input is signalled by the “OPEN” LED.

Several pulse generators connected to these terminals must be connected in parallel.

5.2.3. PHOTOCELLS

Terminals "FSW & FSW". Normally closed contact. Connect, to these terminals, any obstacle detection devices (photocells,

pressure switch, etc...). These devices are active during the closing movement of the shutter and, according to the

dip-switch 4 selection (see paragraph 7), they can cause immediate reversal of motion or stop the motion and resume it after

release. The status of this input is signalled by the “FSW” LED.

Several obstacle detection devices must be connected in series.

If no device is connected, jumper connect the input. The “FSW” LED must always be ON.

5.2.4. POWER SUPPLY FOR ACCESSORIES

Terminals "- & +". Output with 24 V power supply. Connect, to these terminals, the power cables of the accessories connected

to the board. The maximum load of the accessories connected to this input must not exceed 500 mA.

This is a d.c. output; observe the polarity when connecting the accessories.

5.3. RAPID CONNECTOR M3

This connector is dedicated to the coupling of the 5-pin receiver card. Couple and, if necessary, remove the receiver card

only after having cut off the power voltage.

The receiver card can be fit in one direction only, see fig. 4. Do not force.

5.4. TERMINAL BOARD M5 (Fig. 5)

5.4.1. EARTH

Terminal " ". Connect, to this terminal, the yellow-green wire for the control unit earthing coming from the power line.

The connection of the earth wire is absolutely necessary for correct operation of the control unit.

5.4.2. ALIMENTAZIONE

Terminals "F & N". Connect, to these terminals, the cables of the 220 V~ power supply line.

GEO 13

ENGLISH

Guide for the installer

Pagina 9

6. ADJUSTING THE WORK TIME

The work time of the control unit does not depend on the effective operation of the motor. The limit stops stop the motor

motion and identify the shutter position.

The work time of the control unit is identified by the steady light of the “WORK TIME” LED.

The shutter work time can be adjusted from a minimum of 8 seconds up to a maximum of 90 seconds. Turn the trimmer TR1

clockwise to increase the work time of the control unit and, vice versa, turn it counter-clockwise to reduce the work time.

Perform the following instructions to adjust the work time:

Select the “step-by-step” function logic using the dip-switches, see paragraph 7.

Make sure that the trimmer TR1 is approx. at mid-travel.

Adjust the limit stops as described in the gearmotor instructions.

If, during the adjustment, the “WORK TIME” LED turns off before the motor has reached the limit stop, increase the work

time by means of the adjustment trimmer TR1, then repeat the procedure for the limit stop adjustment

When the limit stop adjustment procedure has been completed, adjust the work time.

Command an opening movement of the shutter and check how long the “WORK TIME” LED remains ON on the control

unit. If it stays ON for more than two seconds from the shutter stop, you need to reduce the time by turning the trimmer

TR1 counter-clockwise.

The work time must be adjusted in such a way that the “WORK TIME” LED on the control unit stays ON for about two

seconds after the motor stop.

Command a closing and opening movement of the shutter and check again how long the LED stays ON.

If necessary, repeat the operations from point 5 until the LED turns OFF about two seconds after the motor stop.

With the step-by-step function logic you can stop the work time count by means of the radio control or any other

device connected to the OPEN input.

7. SETTING THE DIP-SWITCHES

Four dip-switches are fitted on the control unit that enable you to select the function logic, the pause time before the automatic

re-closure and the tripping type of the obstacle detection devices during the shutter closing phase. The different available

options are shown in the table below:

Dip-switch Description

Step-by-step logic

Automatic logic with 5-second pause

Automatic logic with 10-second pause

Automatic logic with 15-second pause

Automatic logic with 20-second pause

Automatic logic with 30-second pause

Automatic logic with 45-second pause

Automatic logic with 60-second pause

Behaviour of the obstacle detection devices

Stops the movement and reverses motion into opening

Stops operation and resumes it into closure after release

1.

2.

3.

4.

5.

6.

7.

GEO 13

ENGLISH

Guide for the installer

Pagina 10

The pause time count starts at the end of the work time, “WORK TIME” LED OFF.

All dip-switch adjustments must be performed when the control unit is off and the shutter is closed.

8. CONTROL LEDs

There are 5 control LEDs on the control unit for controlling the status of the inputs and of the control unit. The meaning of each

LED is described in the table below:

LED ON OFF

Power Mains power ON No mains power

Time Work Control unit working Control unit at rest

Stop Command not active Command active

Open Command active Command not active

FSW Obstacle detection devices free Obstacle detection devices engaged

The conditions highlighted in bold refer to the control unit powered and with closed shutter.

9. PROTECTIVE FUSES

There are two protective fuses on the control unit: one is self-resetting. Contrary to the common fuses, where the tripping of the

fuse breaks the element and the fuse must be replaced to resume operation, the tripping of the self-resetting fuses can only be

seen in the missed operation of the part they protect. If this type of fuse is tripped, follow the instructions below:

Cut off the power to the control unit

Check the connection of the non-operating accessories, paying special attention to any possible short-circuit

Make sure that the total load of the connected accessories does not exceed the value indicated in these

instructions

Wait for approx. five minutes, then supply power again.

The following table shows the values of the fuses and the relevant protected parts:

Fuse Protection

F1= T5A/250V 2x20 Board power supply

RV1 = 500mA (self-resetting) Power supply to accessories

10. FUNCTION LOGICS

Step-by-step logic

Shutter status

Pulses

Open Stop

Obstacle detection

Dip-switch 4 = ON Dip-switch 4 = OFF

Closed Opens the shutter

No effect, if pressed

inhibits the OPEN

command

No effect

Open Closes the shutter

No effect, if engaged, inhibits the OPEN

command

Closing

Stops operation Stops operation

Stops operation and

resumes after release

Stops and reverses

motion

Opening No effect

Automatic logic

Shutter status

Pulses

Open Stop

Obstacle detection

Dip-switch 4 = ON Dip-switch 4 = OFF

Closed

Opens the shutter and

re-closes after pause

time

No effect, if pressed

inhibits the OPEN

command

No effect

Open in pause Closes immediately

No effect, if engaged, inhibits the OPEN

command

Closing Stops operation

Stops operation

Stops operation and

resumes after release

Stops and reverses

motion

Opening No effect No effect

1.

2.

3.

4.

Page is loading ...

Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le

caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la

presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza

di carattere costruttivo o commerciale.

The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving

the main features of the equipments unaltered, to undertake any modifications to holds necessary for either technical or

commercial reasons, at any time and without revising the present publication.

Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à

tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans

devoir pour autant mettre à jour cette publication .

Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho,

dejando inmutadas las características esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse

a poner al día la presente publicación, todas las modificaciones que considere oportunas para el perfeccionamiento

técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.

Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne

die wesentlichen Eigenschaften dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der

vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell bedingte Verbesserungen vorzunehmen.

De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment de

veranderingen aan te brengen die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke andere

productie- of commerciële eisen, waarbij de fundamentele eigenschappen van het apparaat gehandhaafd blijven, zonder

zich daardoor te verplichten deze publicatie bij te werken.

Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: / Sello del revendedor: / Fachhändlerstempel: / Stempel

dealer:

Via Padre Elzi, 32 - 24050 - Grassobbio - BERGAMO-ITALY

tel. 0039.035.4242511 - fax. 0039.035.4242600

[email protected] - www.geniusg.com

00058I0889 Rev.0

Genius GEO 13 Operating instructions

Genius GEO 13 Operating instructions

in other languages

Related papers

Other documents