1
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057 Tel: +86-755-26779999
URL: http://www.zte.com.cn E-mail: [email protected]
ZTE MF60
Quick Start Guide
2 4 5 6 73 8 9
LEGAL INFORMATION
Copyright © 2012 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
photocopying and microfilm, without the prior written permission of ZTE
Corporation.
The manual is published by ZTE Corporation. We reserve the right to make
modications on print errors or update specications without prior notice.
Version No. : R1.0
Introduction
ZTE MF60 is a 3G/2G mobile hotspot device, working in GSM/GPRS/
EDGE/WCDMA/HSPA/HSPA+ network. The client devices could connect to
it via USB or Wi-Fi interface. The device supports data and SMS services,
enabling you to communicate anytime and anywhere.
This manual provides instructions on how to install and get started with the
product. For information about connection of services, please consult your
service provider.
Specication
Data Service
HSPA+: DL 21.6 Mbps,
UL 5.76 Mbps
WCDMA CS: 64 kbps UL/DL
WCDMA PS: 384 kbps UL/DL
Interface USB and Wi-Fi
Wi-Fi Standard 802.11b/g
Wi-Fi Security WEP/WPA/WPA2/WAPI
USB Version USB 2.0 HIGH SPEED
USB Interface Type Micro USB
Weight 86 g
Dimensions (W×H×D): 99.6 mm*54 mm*14.6 mm
microSD card Support up to 32 GB microSD card
Power Adapter 5 V/700 mA
Battery 1500 mAh
*Standby time 100 hours
*Working time 4 hours
Operate system
Windows 7, Windows Vista(32bit or 64bit),
Windows XP (SP2 or later)
MAC (10.4 or later)
Web Browser
IE (7.0 or later), Firefox (2.0 or later), Opera (10.0
or later), Safari (4.0 or later), Chrome (5.0 or
later)
Operating temperature 0 °C ~ +35 °C
Storage temperature -20 °C ~ +50 °C
Charging temperature 0 °C ~ +45 °C
Humidity 5%~ 95%
Notes:
microSD is a trademark of SD Card Association.
The device’s standby and working time are only for your reference, and
based on ideal working environment.
Getting to Know Your Device
The following gure shows the appearance of the device, it is only for your
reference. The actual device may be different.
Right Side Front Left Side Bottom
Interface and Buttons
1. Power Button Hold the Power button to switch on/off the device.
2. Memory card slot
(microSD card)
It is where you insert the memory card (microSD
card).
3. WPS Button
4. LED Screen
It indicates the network type, signal strength,
battery status, and Wi-Fi, etc.
5. External Antenna
Port
It is used to connect an external antenna to
enhance the signal strength.
6. Charger/USB port
• Charge your device.
• Connect the client to your device via USB cable.
Notes:
• Hold the WPS and Power buttons simultaneously until the LED
screen turns off, and then release the buttons. The device will restart
automatically and restore to the factory default settings.
• Please use the original external antenna if necessary.
LED Indicator
When the device is powered on, the following icons will appear on the LED
screen, with the corresponding indicates listed in the table below:
Icon Indication
Indicates the network signal strength.
Indicates the network type. 2G or 3G icon will appear on the
LED screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication.
New message received.
Indicates Wi-Fi status and the number of the connecting users.
Indicates the battery status.
Hardware Installation
Inserting SIM Card and Battery
1. Slide the back cover and remove it.
2. Insert the SIM card into the SIM card holder.
3. Insert the battery as shown with the contacts located against the metal
springs, and press the battery down into the case.
4. Slide the back cover and lock the cover in its place.
Inserting microSD Card
1. Pull the microSD cover out of the card slot.
Notes:
Do not pull the cover rudely, as it is connected with the device.
2. Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
3. Close the microSD cover.
Switching On/Off Your Device
Hold the Power button to switch on/off the device.
Notes:
The device is powered on when the LED screen lights up.
Charging Your Device
You can charge your device by using USB cable or adapter.
1. Insert the charger lead carefully.
2. The plug only ts one way. Do not use excessive force to insert the plug.
Working Mode
Your device supports three working modes. For the client, we only use PC or
laptop as the example in this document.
USB Mode: Connect to the device with the USB cable.
Wi-Fi Mode: Connect to the device via Wi-Fi.
Mixed Mode: Connect to the device with the above two connection methods.
Notes:
If you want to connect to the Internet by using Wi-Fi mode, make sure that
the client supports the Wi-Fi function.
The following picture is the application example. All of the client devices can
surf on the Internet at the same time.
Establish a connection between your device and
the client
Via USB Cable
1. Connect your device and the client with the USB cable.
2. Power on your device.
3. Follow the system prompts to complete the software installation.
10 11 12 13 14 15 16 17 18
Notes:
• If the system does not launch installation automatically, you can run the
installation program in path of My Computer > SMART BRO.
• The driver of your device will be installed at the same time.
4. After the installation, the system will create a shortcut icon on your
desktop and a SMART BRO program group in the Start - Programs
menu. The connection between your device and the client will be
established successfully a moment later.
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search the available
wireless network.
Notes:
You need to check your Wireless Network Connection. Set the client
to obtain an IP address automatically in the Internet protocol (TCP/IP)
properties, and the client will get an IP address like “192.168.0.100”.
3. Select the SSID of your device, and then click Connect. The following
gure is only for your reference.
Notes:
Check the label on your device to gain the SSID information.
View the information of WAN, WLAN and Device. Input the case-sensitive
default password “smartbro”, and then click Login to access the WebGUI
Conguration page.
Notes:
• Do not put anything on the top of your device. Do not lay devices to
overlap each other when using.
• The device takes 1~2 minutes to initialize, and attach to the network.
PIN Code Verication
If the PIN code of your SIM card is enabled, you will need to input the PIN
code when you login at the rst time.
Notes:
The SIM card will be locked if you enter wrong PIN code consecutively for
three times.
If you want to modify the PIN Status, please select Settings > Advanced >
PIN Management to do the actions.
Quick Settings
After logging in, select Quick Settings, and then the Quick Setup wizard
appears.
The Quick Settings wizard guides you how to set the basic parameters for
your device in the safest way. After this procedure, you can use your Internet
service.
Notes:
The parameter settings may have been preset by your service provider,
and you will enjoy your Internet service directly. Please contact your service
provider for details if you want to do some modication.
WAN Connection
After logging in, select WAN Connection, and you can choose the WAN
Connection Mode according to your requirement.
Settings
After logging in, select Settings, and you can do the following operations.
Select Settings > 3G
Settings
View the Wireless Information, select Band Selection
Mode and change APN Setting.
Select Settings > Wi-
Fi Settings
View the current station list, change the basic
wireless network settings, choose security mode,
and perform the WPS conguration.
Select Settings >
Firewall
Set the Mac/IP/Port Filtering, Port Forwarding or the
System Security conguration.
Select Settings >
Advanced
View the current status of your device, change the
Administrator Settings, restore factory defaults,
manage PIN or set the LAN interface conguration.
Notes:
Make sure that you can remember the new password if you change the
login password by selecting Settings > Advanced > Management. Please
restore the device to the factory default settings in case you forget the new
password.
Disconnect from the Internet
1. Log in the WebGUI Conguration page, and select WAN Connection.
2. Select Manual > Disconnect Internet.
3. Click Apply.
Notes:
Turning off the device can also terminate the internet connection.
SMS
This function allows you to view, send and receive short messages.
After logging in, select SMS, and you can do the following operations.
Select SMS > Device Operate the SMS in your device.
Select SMS > SIM Card Operate the SMS in your SIM card.
Select SMS > New Message Send or save SMS.
Select SMS > SMS Settings Set the SMS conguration.
on. Turn your device off if necessary. Consult a physician or the
manufacturer of the medical device before using your device.
• Be aware of the usage limitation when using your device at places such
as oil warehouses or chemical factories, where there are explosive gases
or explosive products being processed. Turn off your device if required.
• The use of electronic transmitting devices is forbidden in aircrafts, at
petrol stations and in hospitals. Please observe and obey all warning
signs and switch off your device in these conditions.
• Do not touch the inner antenna area if not necessary. Otherwise it will
affect your device’s performance.
• Store your device out of the reach of little children. Your device may
cause injury if used as a toy.
• Do not touch the metallic parts of your device so as to avoid a burn,
when your device is working.
Using Your Device
• Please use original accessories or accessories that are authorized. Using
any unauthorized accessories may affect your device’s performance, and
violate related national regulations about telecom terminals.
• Avoid using your device near or in side me tallic structures o r
establishments that can emit electromagnetic waves. Otherwise it may
inuence signal reception.
• Your device is not waterproof. Please keep it dry and store in a shady
and cool place.
• Do not use your device immediately after a sudden temperature change.
In such case, it will produce dew inside and outside your device, so don’t
use it until it becomes dry.
• Handle your device carefully. Do not drop, bend or strike it. Otherwise
your device will be damaged.
• No dismantling by non-professionals and only qualied technicians can
undertake repair work.
• Operating temperature range of 0 °C ~ +35 °C and humidity range of 5%
~ 95% are recommended.
• Do not use the device in an enclosed environment or where heat
dissipation is poor. Prolonged work in such space may cause excessive
heat and raise ambient temperature, which may lead to automatic
shutdown of the device for your safety. In the case of such event, cool
the device in a well-ventilated place before turning on for normal use.
Using Battery
• Do not short-circuit the battery, as this can cause excessive heat and
re.
• Do not store battery in hot areas or dispose of it in a fire to avoid
explosion.
• Do not disassemble or modify the battery.
• When not using the battery for a long period, remove it from your device
and store it in a cool dry place.
• Never use any charger or battery damaged or worn out.
• Return the wear-out battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
Warning:
If the battery is broken, keep away from it. If it taints your skin, wash your
skin with abundant fresh water and ask doctor help if necessary.
Limited Warranty
• This warranty does not apply to defects or errors in the Product caused
by:
i. Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or
maintenance instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper installation,
disassembly, storage, servicing or operation of the Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified
individual.
v. Power failures, surges, re, ood, accidents, actions of third parties
or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with third-party
products provided that such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for the
Product.
End User shall have no right to reject or return the Product, or receive a
refund for the Product from ZTE under the above-mentioned situations.
• This warranty is End User’s sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
expressed, implied or statutory, including but not limited to the implied
warranties of merchantability and tness for a particular purpose, unless
otherwise required under the mandatory provisions of the law.
Limitation of Liability
ZTE shall not be liable for any loss of prots or indirect, special, incidental or
consequential damages resulting from or arising out of or in connection with
using of this product, whether or not ZTE had been advised, knew or should
have known of the possibility of such damages, including, but not limited to
lost prots, interruption of business, cost of capital, cost of substitute facilities
or product, or any downtime cost.
How to Get Help
You can get help by:
• Sending E-mail to [email protected]
• Visiting http://www.zte.com.cn
• Calling Service Hotline: +86–755–26779999
4. Wait a moment, the connection between your device and the client will
be established successfully.
Access the Internet
1. Switch on the device.
2. Establish a connection between your device and the client.
3. After successfully establishing the connection, access the Internet in the
Always On and Manual mode. The default mode is Always On.
Notes:
You can browse the WebGUI Conguration page and click WAN Connection
to set the WAN connection mode.
Access the WebGUI Conguration Page
1. Make sure the connection between your device and the client is correct.
2. Launch the internet browser and enter http://192.168.0.1 or http://ufi.
home in the address bar.
Notes:
It is recommended that you use IE (7.0 or later), Firefox (2.0 or later), Opera
(10.0 or later), Safari (4.0 or later), Chrome (5.0 or later).
3. The login page appears as follows. The following gure is only for your
reference.
PhoneBook
This function allows you to store contacts to your device or SIM card.
After logging in, select PhoneBook, and you can add a new contact in Add
New tab, and perform operations to the contact in the Device or SIM Card
tab.
Usage of WPS
If your client device supports WPS, you need not to input the password
manually after WPS has been available. Please do the following:
1. Start up your device.
2. Launch the client device connected to your device.
3. Enable the WPS function of your device.
4. Enable the WPS function of the client.
Notes:
For the detailed operations about the client, please refer to the client’s
instruction.
Warning and Notice
To the Owner
• Some electronic devices are susceptible to electromagnetic interference
sent by your device if inadequately shielded, such as the electronic
system of vehicles. Please consult the manufacturer of your device
before using if necessary.
• Operating your device may interfere with medical devices like hearing
aids and pacemakers. Please always keep them more than 20
centimeters away from such medical devices when they are turned
-
1
-
2
