Mountfield HP45 Operating instructions

Brand: Mountfield

Model: HP45

Category: Lawnmowers

Type: Operating instructions

This manual is also suitable for

SP454

Mountfield HP45 is a lawnmower designed to provide safe and reliable service for many years. It is equipped with a Mountfield WB45 engine, a fuel tank, and a grass collector. It has a lever-operated clutch and operator presence control for safe operation. The deflector flap allows for easy disposal of grass clippings, and the spark plug is easily accessible for maintenance. It is powered by fresh fuel and is equipped with a fuel drain screw for easy maintenance.

Please Read These Instructions

Before Using Your Mower

Operating Instructions

for models

HP454 & SP454 Lawnmowers with Mounteld WB45 engine

HP45 Lawnmower with Mounteld RS100 engine

HP45H Lawnmower with Honda GCV 160 engine

Product Codes:

299194643/BQ

299294643/BQ

299014643/BQ

299014633/BQ

Do not return this product to store, please call

the Service Link Helpline

Products with petrol in cannot be accepted

back in store

Supported by

For all your Warranty,

Parts and Service needs

0800 121 6585

www.servicelink.org.uk

Visit www.servicelink.org.uk for a quick start video

ENGLISH (Original instructions)

- Safety precautions ..................................................................................3-4

- Know your mower ...................................................................................4-6

- How to get mowing ...............................................................................7-10

- Maintenance .................................................................................... ........11

- Fault Finding ............................................................................................12

GUARANTEE ............................................................................................13

Thank you for purchasing a Mounteld lawnmower. This machine will give you many years of safe and

reliable service if operated in accordance with these instructions.Please read and understand these

Operating Instructions before using your mower. Failure to do so could result in personal injury

or damage to the equipment.

NEVER TIP THE MOWER ON ITS SIDE AS THIS WILL FLOOD THE AIR FILTER WITH OIL.

To access the underside, lift the front wheels by lowering the handle until it rests on the ground.

SAFETY PRECAUTIONS

Your lawnmower should be used with due care and attention. Symbols have therefore been placed on various parts of

the machine to remind you of the main precautions to be taken. Their meaning is explained below. You are also asked

to carefully read the safety regulations in the applicable chapter of this handbook

1. Warning: Read the instruction manual before using the machine.

2. Beware of thrown objects: Keep other people at a safe distance

whilst working.

3. Beware of cutting: Moving blades. Do not put hands or feet near

the blades. Disconnect the spark plug before carrying out any repairs or

maintenance.

4. Only for electric lawnmowers.

5. Only for electric lawnmowers.

6. Warning: the blade will continue to rotate for a while after you have

switched o the lawnmower.

DESCRIPTION OF SYMBOLS ON CONTROLS (where foreseen)

11. Engine stop 12. Drive on

Maximum noise and vibration levels

Operator’s ear noise pressure level ................................................ db(A) 81

- Measurement uncertainty ............................................................ db(A) 0,5

______________________________________________________________

Measured acoustic output level...................................................... db(A) 95

- Measurement uncertainty ............................................................ db(A) 0,35

______________________________________________________________

Guaranteed acoustic output level ................................................... db(A) 96

______________________________________________________________

Vibration level ................................................................................ m/s 7,72

- Measurement uncertainty ........................................................... m/s 0,9

1. Acoustic power level

2. Conformity mark

3. Year of manufacture

4. Type of lawnmower

5. Serial number

6. Name and address of manufacturer

7. Article code

8. Engine power and speed

9. Weight in kilograms

As soon as you have purchased the machine, do not forget to write the identication numbers (3-4-5-7) in the spaces

on the last page of the manual.

KNOW YOUR MOWER

Operaror Presence Control

(OPC) (Lever-upper)

Clutch Lever

(Lever-lower)

Pull Cord & Guide

Deflector Flap

Engine

Cutter Deck

Handle Securing Knob

Fuel Filler Cap

Grass Collector

Fuel drain screw

Primer

Spark Plug

The following safety precautions must be observed at all times. Please read them carefully.

TRAINING

1) Read the instructions carefully. Get familiar with the controls and proper use of the equipment. Learn how to

stop the engine quickly

2) Only use the lawnmower for the purpose for which it was designed, i.e. for cutting and collecting grass.

Any other use can be hazardous, causing damage to the machine. Examples of improper use may include, but

are not limited to:

– transport of people, children or animals on the machine;

– being transported by the machine;

– using the machine to tow or push loads;

– using the machine for leaf or debris collection;

– using the machine to trim hedges, or for cutting vegetation other than grass;

– use of the machine by more than one person;

– using the blade on surfaces other than grass.

3) Never allow children or people unfamiliar with these instructions to use the lawnmower. Local regulations may

restrict the age of the operator.

4) Never use the lawnmower:

– When people, especially children, or pets are nearby.

– If the operator has taken medicine or substances that can aect his ability to react and concentrate.

5) Remember that the operator or user is responsible for accidents or hazards occurring to other people or their

property.

PREPARATION

1) While mowing, always wear sturdy footwear and long trousers. Do not operate the equipment when

barefoot or wearing open sandals.

2) Thoroughly inspect the area where the equipment is to be used and remove all objects which may be thrown by

the machine or damage the cutter assembly and the engine (stones, sticks, metal wire, bones, etc.)

3) WARNING: DANGER! Engine fuel is highly ammable:

– Store fuel in containers specically designed for this purpose.

– Refuel using a funnel and outdoors only. Do not smoke while refuelling or whenever handling the fuel

– Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel while the engine is running

or when the engine is hot.

– If fuel is spilt, do not attempt to start the engine but move the machine away from the area of spillage and avoid

creating any source of ignition until the fuel has evaporated and the vapour dispersed.

– Replace all fuel tanks and containers caps securely.

4) Substitute faulty silencers. Never use the machine without silencer.

5) Before use, always inspect the machine, especially the condition of the blades and check that the

screws and cutting assembly are not worn or damaged. Replace worn or damaged blades and screws in

sets to preserve balance.

6) Before mowing, attach the discharge opening guards (grass-catcher or stone-guard).

7) Only use fresh fuel (no older than 28 days).

OPERATION

1) Do not operate the engine in a conned space where dangerous carbon monoxide fumes can collect.

2) Mow only in daylight or good articial light.

3) If possible, avoid operating the equipment in wet grass.

4) Always be sure of your footing on slopes.

5) Walk, never run and do not allow yourself to be pulled along by the lawnmower.

6) Mow across the face of slopes, never up and down.

7) Exercise extreme caution when changing direction on slopes.

8) Do not mow on slopes of more than 20°.

9) Exercise extreme caution when pulling the lawnmower towards you

10) Stop the blade if the lawnmower has to be tilted for transportation when crossing surfaces other than grass and

when transporting the lawnmower to and from the area to be mowed.

11) Never operate the lawnmower with defective guards, or without safety devices, such as the stone-guard and/or

grass-catcher, in place.

12) Do not change the engine governor settings or overspeed the engine.

13) On power-driven models, disengage the drive clutch before starting the engine.

14) Start the engine carefully, following the instructions and keeping feet well away from the blade.

15) Do not tilt the lawnmower when starting the engine. Start the engine on a at surface that is free of obstacles and

tall grass.

16) Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

17) Never pick up or carry a lawnmower while the engine is running.

18) Stop the engine and disconnect the spark plug wire:

– Before carrying out any work underneath the cutting deck or before unclogging the chute;

– Before checking, cleaning or working on lawnmower;

– After striking a foreign object. Inspect the lawnmower for damage and make repairs before restarting and

operating the lawnmower;

– If the lawnmower begins to abnormally vibrate immediatly look for the cause of the vibrations and take the

mower to your local Mounteld Service Dealer.

19) Stop the engine:

– Whenever you leave the lawnmower unattended. Remove the key from models with electric starters.

– Before refuelling.

– Every time you remove or replace the grass-catcher.

– Before adjusting the grass cutting height.

20) Reduce the throttle before turning o the engine when you have nished mowing, following the instructions in the

engine handbook.

21) When mowing, always keep to a safe distance from the rotating blade. This distance is the length of the handle.

MAINTENANCE AND STORAGE

1) Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. Regular maintenance

is essential for safety and performance.

2) Never store the equipment with fuel in the tank inside a building where vapour may reach a ame or a spark or a

source of extreme heat.

3) Allow the engine to cool before storing in an enclosed space.

4) To reduce the re hazard, keep the engine, exhaust silencer, battery compartment and fuel storage

area free of grass, leaves, or excessive grease. Do not leave containers with grass cuttings in rooms.

5) Check the stone-guard and grass-catcher frequently for wear and deterioration.

6) If the fuel tank has to be drained, this should be done outdoors and when the engine is cool.

7) Wear strong work gloves when removing and reassembling the blade.

8) Keep the blade balanced during sharpening. All operations on the blade (dismantling, sharpening, balancing,

remounting and/or replacing) require a certain familiarity and special tools. For safety reasons, these jobs are

best carried out at a specialised centre.

9) For safety reasons, never use the machine when it has worn or damaged parts. Parts are to be replaced

and not repaired. Use genuine spare parts. Parts that are not of the same quality can damage the

equipment and impair your safety.

10) If the machine is not going to be used for 28 days or more please drain all fuel from the machine. Stale fuel can

cause damage to the carburettor.

TRANSPORTATION AND HANDLING

1) Whenever the machine is to be handled, raised, transported or tilted you must:

– wear strong working gloves;

– grasp the machine at the points that oer a safe grip, taking account of the weight and its distribution.

– use an appropriate number of people for the weight of the machine and the characteristics of the vehicle or the

place where it has to be placed or collected.

2) During transport, fasten the machine securely with ropes or chains.

HOW TO GET MOWING

Your Mounteld lawnmower does not contain petrol or oil and these must be added before use.

Running the mower with insucient oil can cause serious damage to the engine and will invalidate your

warranty.

NEVER TIP THE MOWER ONTO ITS SIDE AS THIS WILL FLOOD THE AIR FILTER WITH OIL.

To access the underside of the machine lift the front wheels by lowering the handle to the ground.

Carefully remove the mower from the box and read these Operating Instructions. An Owner’s Manual for the engine

is also included. Please read this before starting the engine.

WARNING - Unpacking and completing the assembly should be done on a at and stable surface,

with enough space for machine handling and its packaging, always making use of suitable equipment.

Disposal of the packaging should be done in accordance with the local regulations in force

HANDLE ASSEMBLY (Figure 1)

• Attach the bottom of the handle to the holes on the side of the cutter deck. Secure it using the bolts supplied. An

allen key to tighten the nuts is located at the base of the handles.

• Fit the top handle using the nuts & bolts provided.

• Engage the Operator Presence Control (OPC) lever by pulling and holding it against the handle in order to

release the engine brake. Pull the starter cord and t it into the cord guide as shown. Tighten the nut using a

10mm spanner. Failure to use the cord guide will result in premature cord wear.

• Secure the control cables using the clamp. Take care that the cables are not secured too tightly (this may impair

how the mower operates) or impair removal of the grass collector. The clutch cable and control lever are only

tted to models with power drive (SP454).

Figure 1

GRASS COLLECTOR (Figure 2)

Fabric grass collector: Fit the fabric bag over the steel frame and then snap the bag onto the plastic lid.

Figure 2

GRASS CUTTING

This machine cuts lawns in various modes; before starting work, prepare the machine based on how the lawn is to

be mowed.

MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF

HOW TO USE

“Mulching” – Chopping and depositing grass on the

lawn

Cutting and collecting grass cuttings

Cutting and ejecting grass cuttings

Standards of use

1) Alwaystanddismantletheaccessorywiththeengine

o,afterremovingtheignitionkey(ifsupplied),orafter

disconnectingthecapfromtheenginesparkplug.

2) Apply the “mulching” accessory and check that the

ttedpartshavebeenfastenedcorrectlyandsecurely.

3) You always need to work with the grass-catcher or

stone-guard tted properly even when using the

“mulching”accessory.

4) Always avoid removing a large quantity of grass, to

avoid blocking the cutting deck or overloading the

engine and the cutting parts. Regulate the forward

speed depending on the lawn conditions and the

quantityofgrassremoved.

INSTRUCTIONS FOR ASSEMBLY AND DISMANTLING

Assembly

Lift the stone-guard and t the mulching plug (1) in the

outlet. Fasten it by tting the two pins (2) into the holes

provided until the fastener tooth clicks into place (3).

Dismantling

Lift the stone-guard and press down on the centre until the

tooth (3) is released and remove the mulching plug (1).

STARTING YOUR MOWER

Read and understand the Safety Precautions before using your mower.

• Put Mounteld 4-stroke oil, part number MX855, available from any Mounteld stockist or B&Q store, SAE 30 or

10W-30 oil, in the oil ller (Figure 3). Do not overll.

The oil tank capacity for models:

HP454 & SP454 is 0,5 litre

HP45 is 0,45 litre

HP45H is 0,55 litre

• Fill the fuel tank with UNLEADED petrol. Use only clean, fresh petrol - stale fuel may contain deposits that will

clog the carburettor. Unleaded fuel can start to go stale after just 28 days. For model HP45H a fuel stabiliser is

recommended to help prevent fuel becoming stale. We recommend the use of Mounteld universal fuel stabiliser.

Do not overll, the petrol level should be below the bottom of the fuel tank neck. Do not over tighten the fuel cap.

The fuel cap breathes through the threads of the cap and over tightening can cause the engine to cut out.

• Ensure that the spark plug lead is securely connected to the spark plug.

• Press the “PRIMER” device button (Figure 4) 3 times to prime the carburettor (for models HP454, SP454 and

HP45).

• Turn on the fuel tap which is located beside the air lter (close up in Figure 3 for model HP45H)

For models HP454 & SP454

Figure 3

Figure 4

Spark plug

Oil Filler Cap /

Dipstick

Fuel Filler Cap

Air filter

Exhaust

Pull Cord

Handle

For model HP45

Figure 4Figure 3

Pull Cord Handle

Oil Filler Cap /

Dipstick

Exhaust

Fuel Filler Cap

Spark Plug

Air Filter

Primer

For model HP45H

Fuel filler cap

Pull Cord Cable

Oil Filler Cap

Dipstick

Exhaust

Spark Plug

Air Filter

Fuel Tap

(On)

Figure 3

• Pull and hold the Operator Presence Control (OPC) lever against the handle to disengage the engine brake.

THE ENGINE WILL NOT START, OR CONTINUE TO RUN, UNLESS THE OPC LEVER IS HELD AGAINST

THE HANDLE

• Pull the starter cord with a strong smooth pull. Do not remove the pull cord from the guide.

• When the engine starts move the throttle control from “Choke” to the “Fast” position.

• To engage the drive to the rear wheels on Self Propelled models, pull and hold the clutch lever against the handle.

• To stop the drive, release the clutch lever

NOTE:Usingthechokeisusuallyunnecessarywhenstartingawarmengine.However,incoolweatheritmaystillbe

necessarytousethechoketostarttheengine.

STOPPING YOUR MOWER

• Release the Operator Presence Control (OPC) lever; this will engage the engine brake and operate the ignition

safety cut out device.

ADJUSTING THE HEIGHT OF CUT

The height of cut adjustment not only determines the length of the cut grass, it also controls the airow which carries clippings

into the collector. If the discharge chute becomes blocked, increase the airow by raising the height of cut. To prevent blockages

when cutting long, thick grass, set the adjustment to the highest setting and cut the grass; then cut it again on a lower setting.

To adjust the height of cut:

• Stop the engine and disconnect the spark plug

• Put the mower on a level surface

• Adjust the cutting height lever by pulling outwards and moving into the

required position (Figure 5)

Figure 5

BEFORE EACH USE

• Always ensure that the mower is in a safe working condition. Inspect the cutter blade for damage; check safety

devices and guards; check that all nuts, bolts and screws are secure.

• Check the oil level as follows:

a) Remove the oil ller cap and wipe the dipstick clean (Figure 6).

b) Ret the dipstick into the ller neck, do not screw it down. Remove the dipstick and check the oil level; oil should be at

the MAX mark. The oil tank capacity is for models:

HP454 & SP454 - 0,5 litre or 20 uid oz

HP45 - 0,45 litre or 20 uid oz

HP45H - 0,55 litre or 20 uid oz

c) If the oil level is low add Mounteld oil part number MX855 or a SAE 30 or 10W-30 oil, to the upper limit on the dipstick.

Do not overll; the oil level should not be above the MAX mark.

• Fill the fuel tank with unleaded petrol. Do not overll, there is no need to ll tank to the top. The fuel tank need only

contain enough fuel to complete the days mowing. If you run out of fuel, relling must only be carried out once the

engine has cooled. Fuel stored within the machine for 28 days or more can go stale and should be drained before

further use.

HP454 & SP454 HP45 HP45H

Figure 6

MAX

MIN

Oil Filler Cap

Dipstick

MAX

MIN

Figure 6

MAINTENANCE

Stop the engine and disconnect the spark plug lead before working on the machine.

DO NOT TIP THE MOWER ONTO ITS SIDE AS THIS WILL FLOOD THE AIR FILTER WITH OIL.

To access the underside of the machine, lift the front wheels by lowering the handle until it rests on the ground.

CUTTER BLADE

Examine the cutter blade regularly for wear or damage.

• A slightly worn blade can be re-sharpened by your local dealer

• If the blade is damaged it should be replaced. Replacement blade kits are available from

your Mounteld stockist or B&Q store. The part number for the blade kit is MS1196. If in

doubt refer to your dealer, or telephone 0800 121 6585.

Blade must always be marked with part number

81004365/3

CLUTCH CABLE ADJUSTMENT (Self Propelled model only)

• Make sure that the clutch lever is fully released.

• Slacken the bottom nut and then tighten the top nut on the adjuster to take up any

excess slack in the cable. The cable should have about 12mm of play on it (Figure 7).

• Engage the clutch lever and check that the rear wheels lock when the mower is pulled

backwards.

• Start the mower and ensure it does not drive when the lever is disengaged.

adjuster

cable

Figure 7

ENGINE

An engine Manufacturer’s Owner’s Manual is supplied with your mower.

Please read this, it provides detailed information on engine operation, maintenance and battery care. Repair work

other than routine maintenance, should be carried out by an authorised dealer.

STORAGE

A little time spent on your mower after use will ensure many years of reliable mowing.

To access the underside of the cutter deck, ensure that the spark plug lead is disconnected. Then lift the front wheels

by lowering the handle until it rests on the ground. Do not tip the mower onto its side, as this will ood the air lter

with oil. Failure to maintain and care for your engine may invalidate the machine guarantee. Please see the guarantee

statement for full terms and conditions.

AFTER EACH USE

• Remove any grass pulp from the underside of the cutter deck using a non-metallic instrument such as a piece of

wood. Take care not to damage the paintwork.

• Examine the cutter blade for any damage. A damaged blade may upset the balance of your mower and cause

excessive vibration. If in doubt refer to your dealer.

• Inspect the grass collector and clean it if necessary. If the mesh becomes clogged airow will be reduced and impair

grass collection.

• The handle can be folded down to reduce the amount of storage space required. Take care not to trap any of the

operating cables when folding or unfolding the handle.

• Store the mower in a clean, dry area well away from any naked ames, sparks or heat source

LONG TERM - (if you are not using your mower for more than 28 days)

• Give the machine a thorough clean, paying particular attention to the underside

• Lubricate all moving parts

• Empty the fuel tank either by running the mower out of fuel or tip the machine backwards and onto the back right wheel to

drain the fuel into a suitable container. To drain the carburettor it is necessary to slacken the drain screw. The drain screw

is situated under the carburettor on the oat bowl (see diagram page 4). A bolt holds the bowl in place on the very bottom,

but on an angle slighlty closer to you is another bolt with a red washer. This is the drain screw.

FAULT FINDING

PROBLEM SOLUTION

Engine will not start

Check there is ample clean, fresh fuel in the tank. Any stale fuel needs to be drained

from the machine.

Check the cutter blade is not fouling the ground preventing free rotation.

Check the petrol ller cap isn’t on too tightly - it should only be nger tight.

Engine will not stop

Check the Operator Presence Control (OPC) lever is fully released.

Remove spark plug lead to stop the engine using insulated gloves and refer to dealer.

Engine smokes Engine may be overlled with oil or may have been tipped.

Engine running unevenly

Check the petrol ller cap isn’t too tight - it should only be nger tight. If fuel is over 28

days old it has gone stale and will need replacing.

Failure to cut grass

properly

Stop the engine and disconnect the spark plug lead using heat resistant gloves.

Check blade attachment bolt is tight.

Check condition of blade.If seriously worn or damaged replace with a new one.

Failure to collect grass

properly

Stop the engine and disconnect the spark plug lead using heat resistant gloves.

Check and make sure there is no build up of grass inside the casing.

Check grass collector is allowing air to ow through the fabric. If it is clogged

it should be washed carefully.

If the grass collector is not clogged raise the height of cut to increase airow.

Check to ensure the engine is running at the correct speed (approximately 3,000rpm)

If conditions are too severe to use the grass collector, remove it and work with the

deector in position.

Machine vibrates

excessively

This will certainly indicate that the blade has become badly damaged. Stop the engine,

disconnect the spark plug lead and examine the blade assembly. Refer to your local dealer.

HELPLINE

0800 121 6585

or visit

www.servicelink.org.uk

This product is supported by Service

Link. If you have been unable to find the

information you require above please

call the Service Link helpline. Here you

will find 1-2-1 help and advice from

garden machinery repair specialists.

Service link

> What is Service Link? Service Link is an aftersales help and

advice helpline with a national network of garden machinery

repair specialists.

> How can we help you? Here at Service Link we can help with

all your trouble shooting, warranty, parts and service needs.

Call us and speak to one of our advisors and if required, visit one

of our 450 centres across the UK and Ireland.

> How can you contact us? If in the unlikely event that this

product does require our help please contact the helpline on

0800 121 6585 in the UK or 1800806149 in ROI. Lines are

open

Monday-Saturday 9am to 5pm and Sundays 10am to 4pm. Also

find us online at www.servicelink.org.uk.

CERTIFICATE OF CONFORMITY

A certicate of conformity is enclosed with the documentation as separate document.

An EXAMPLE is here on the bottom.

doc_base r. 5- wbh-p_0

DICHIARAZIONE CE DI CONFORMITÁ

(Direttiva Macchine 2006/42/CE, Allegato II, parte A)

1. La Società: GGP Italy S.p.A. – Via del Lavoro, 6 – 31033 Castelfranco Veneto (TV) – Italy

2. Dichiara sotto la propria responsabilità, che la macchina: Tosaerba con conducente a piedi / taglio erba

a) Tipo / Modello Base

ES/ESL 464

b) Modello commerciale

c) Anno di costruzione

d) Matricola

e) Motore a scoppio

3. É conforme alle specifiche delle direttive:

• MD: 2006/42/EC

f) Ente Certificatore

g) Esame CE del tipo:

• OND: 2000/14/EC, ANNEX VI - 2005/88/EC

D. Lgs. 262/2002, ANNEX VI, proc. 1 (Italy)

f) Ente Certificatore: N°0197 – TÜV Rheinland LGA Products GmbH

Tillystrasse 2, 90431 Nürnberg – Germania

• EMCD: 2004/108/EC

4. Riferimento alle Norme armonizzate:

EN ISO 5395-1:2013

EN ISO 5395-2:2013

i) Livello di potenza sonora misurato

95 dB(A)

j) Livello di potenza sonora garantito

96 dB(A)

k) Ampiezza di taglio

44 cm

q) Persona autorizzata a costituire il FascicoloTecnico: GGP ITALY S.p.A.

Via delLavoro, 6

31033 Castelfranco Veneto (TV) - Italia

r) Castelfranco V.to, 17.06.2014 Vice Presidente R&D &Quality

Ing. Raimondo Hippoliti

171513900_2

Déclaration CE de Conformité

(Directive Machines 2006/42/CE, Annexe II, partie

1. La Société

2. Déclare sous sa propre responsabilité que la

machine :

Tondeuse à gazon à conducteur a pied / coupe

du gazon

a) Type / Modèle de Base

b) Modèle commercial

c) Année de construction

d) Série

e) Moteur: moteur essence

3. Est conforme aux prescriptions des

directives :

f) Organisme de certification

g) Examen CE du Type

4. Renvoi aux Normes harmonisées

i) Niveau de puissance sonore mesuré

j) Niveau de puissance sonore garanti

k) Largeur de coupe

q) Personne habilitée à établir le Dossier

Technique

Technique :

r) Lieu et Date

EC Declaration of Conformity

(Machine Directive 2006/42/EC, Annex II, part A)

1. The Company

2. Declares under its own responsibility that the

machine:

Pedestrian controlled lawn mower / Grass

cutting

a) Type / Base Model

b) Commercial model

c) Year of manufacture

d) Serial number

e) Motor: petrol

3. Conforms to directive specifications:

f) Certifying body

g) EC examination of Type

4. Reference to harmonised Standards

i) Sound power level measured

i) Sound power level guaranteed

k) Range of cut

q) Person authorised to create the Technical

Folder:

r) Place and Date

EG-Konformitätserklärung

(Maschinenrichtlinie 2006/42/EG, Anhang II, Teil

1. Die Gesellschaft

2. Erklärt auf eigene Verantwortung, dass die

Maschine:

Handgeführter Rasenmäher / Rasenschnitt

a) Typ / Basismodell

b) Handelsmodell

c) Baujahr

d) Seriennummer

e) Motor: Verbrennungsmotor

3. Den Anforderungen der folgenden Richtlinien

entspricht:

f) Zertifizierungsstelle

g) EG-Baumusterprüfung

4. Bezugnahme auf die harmonisierten Normen

i) Gemessener Schallleistungspegel

j) Garantierter Schallleistungspegel

k) Schnittbreite

q) Zur Verfassung der technischen Unterlagen

befugte Person:

r) Ort und Datum

EG-verklaring van overeenstemming

(Richtlijn Machines 2006/42/CE, Bijlage II, deel A)

1. Het bedrijf

2. Verklaart onder zijn eigen

verantwoordelijkheid dat de machine:

Lopend bediende grasmaaier / grasmaaier

a) Type / Basismodel

b) Handelsmodel

c) Bouwjaar

d) Serienummer

e) Motor: benzinemotor

3. Voldoet aan de specificaties van de

richtlijnen:

f) Certificatie-instituut

g) EG-onderzoek van het Type

4. Verwijzing naar de Geharmoniseerde normen

i) Gemeten niveau van geluidsvermogen

j) Gegarandeerd niveau van geluidsvermogen

k) Snijbreedte

q) Bevoegd persoon voor het opstellen van het

Technisch Dossier

r) Plaats en Datum

Declaración de Conformidad CE

(Directiva Máquinas 2006/42/CE, Anexo II, parte

1. La Empresa

2. Declara bajo su propia responsabilidad que la

máquina:

Cortadora de pasto con operador de pie / corte

hierba

a) Tipo / Modelo Base

b) Modelo comercial

c) Año de fabricación

d) Matrícula

e) Motor: motor de explosión

3. Cumple con las especificaciones de las

directivas:

f) Ente certificador

g) Examen CE del Tipo

4. Referencia a las Normas armonizadas

i) Nivel de potencia sonora medido

j) Nivel de potencia sonora garantizado

k) Amplitud de corte

q) Persona autorizada a realizar el Manual

Técnico:

r) Lugar y Fecha

Declaração CE de Conformidade

(Diretiva de Máquinas 2006/42/CE, Anexo II,

parte A)

1. A Empresa

2. Declara sob a própria responsabilidade que a

máquina:

Corta-relvas para operador apeado / corte da

relva

a) Tipo / Modelo Base

b) Modelo comercial

c) Ano de fabricação

d) Matrícula

e) Motor: motor a explosão

3. É conforme às especificações das diretivas:

f) Órgão certificador

g) Exame CE do Tipo

4. Referência às Normas harmonizadas

i) Nível medido de potência sonora

j) Nível garantido de potência sonora

k) Amplitude de corte

q) Pessoa autorizada a elaborar o Caderno

Técnico

r) Local e Data

EK-∆ήλωση συµµόρφωσης

(Οδηγία Μηχανών 2006/42/CE, Παράρτηµα II,

µέρος A)

1. Η Εταιρία

2. ∆ηλώ νει υπεύθυνα ότι η µηχανή:

Χλοοκοπτική µηχανή µε όρθιο χειριστή / κοπή

της χλόης

a) Τύπος / Βασι κό Μοντέλο

b) Εµπορικό Μοντέλο

c) Έτος κατασκευής

d) Αριθµ ός µητρώου

e) Κινητήρας: κινητήρας εσω τερικής ανάφλεξης

3. Συµµορφώνεται µε τις προδιαγραφές της

οδηγίας:

f) Οργανισµός πιστοποίησης

g) Εξέταση CE του Τύπου

4. Αναφο ρά στους Κανονισµούς εναρµόνισης

i) Στάθµη µέτρησης ακουστικής ισχύος

j) Στάθµη εγγυηµένης ακουστικής ισχύος

k) Εύρος κοπής

q) Εξουσιοδοτηµένο άτοµο για την κατάρτιση

του Τεχνικού Φυλλαδίου:

r) Τόπος και Χρόνος

AT Uygunluk Beyanı

(2006/42/CE Makine Direktifi, Ek II, bölüm A)

1. Şirket

2. Şahsi sorumluluğu altında aşağıdaki

makinenin:

Ayak kumandalı çim biçme makin esi / çim kesimi

a) Tip / Standart model

b) Ticari model

c) İmalat yılı

d) Sicil numarası

e) Motor: patlamalı motor

3. Aşağıdaki direktiflerin özelliklerine uygun

olduğunu beyan etmektedir:

f) Sertifikalandıran kurum

g) ... Tipi CE incelemesi

4. Harmonize standartlara atıf

i) Ölçülen ses güç seviyesi

j) Garanti edilen ses güç seviyesi

k) Kesim genişliği

q) Teknik Dosyayı oluşturmaya yetkili kişi:

r) Yer ve Tarih

Декларација за усогласеност со ЕУ

(Директива за машини 2006/42/CE, Анекс II,

дел A)

1. Компанијата

2. изјавува со целосна лична одговорност

дека следната машина:

Тревокосачка со оператор на нозе / косење

трева

а) Тип / основен модел

б) комерцијален модел

в) година на производство

г) етикета

д) мотор: мотор со согорување

3. Усогласено со спецификациите според

директивите:

ѓ) тело за сертификација

е) тест СЕ за типот

4. Референци за усогласени нормативи

з) измерено ниво на звучна моќност

ѕ) Ниво на гарантирана звучна моќност

и) обем на сечење

н) овластено лице за составување на

Техничката брошура

њ) место и датум

EXAMPLE

Guarantee

Congratulations on the purchase of your Mounteld lawnmower. This product has been manufactured to the

highest quality standards and is guaranteed for domestic use against faulty parts or manufacture for a period of 2

years from the date of purchase. Please note that if the machine is used commercially the guarantee period is 90

days from the date of purchase. If you experience any problem with your Mounteld lawnmower please call our

technical helpline on 0800 121 6585 and our operators will endeavour to solve your problem. In the event your

problem cannot be resolved over the phone the operator will refer you to one of our local authorised service centres.

This guarantee is subject to the following terms;

• This guarantee is not transferable. An original proof of purchase will be required in the event of a claim.

• The product must be serviced at the recommended intervals by an authorised service centre. A

service schedule should be kept including invoicing and receipts.Please phone 0800 121 6585 to

locate your nearest Mounteld service centre or visit www.servicelink.org.uk. Service procedures

(for example carb cleaning, draining engine oil, blade sharpening, belt and cable adjustment) and

consumable parts that require periodic replacement (for example the spark plug, air lter and oil) are

not covered under this guarantee. This also applies to parts subject to fair wear and tear (for example

wheels, bearings, starter cord, cables, belts and blade).

• Delivery and collection of the machine is your responsibility and not covered under this guarantee.

• The guarantee does not cover any breakages or damage that are a result of the following; misuse,

alteration, improper assembly or adjustment, neglect or accident.

• Expenses and costs incurred from loss of utility will not be compensated.

• The guarantee does not cover machines that are transported outside of the UK & Eire.

• Where a mower is tted with an engine not manufactured by Mounteld, the engine manufacturer

guarantees the engine.

This guarantee is in addition to and does not detract from your contractual rights under statute or common law.

On delivery of your new Mounteld mower, we suggest

that you complete the box to the right.

The information for your machine is on the serial

number label, which is xed on the cutter deck at the

base of the handles. You will be asked for these details

if you have any problems or require spare parts.

Please keep your receipt, proof of purchase will be

required in the event of a claim.

Service Record

1st Service 2nd Service

Date of service ................................................

Next service due ............................................

Dealer’s Signature ........................................

Dealer’s Stamp:

Date of service ................................................

Next service due ............................................

Dealer’s Signature ........................................

Dealer’s Stamp:

GGP UK LIMITED

Unit 8, Bluewater Estate, Bell Close, Plympton, Plymouth, Devon, PL7 4JH, England.

manufacturedbyGGPITALYSpAViadelLavoro,6I-31033CastelfrancoVeneto(TV)Italy

Part Number 171504001/3

Mountfield HP45 Operating instructions

Brand: Mountfield

Model: HP45

Category: Lawnmowers

Type: Operating instructions

This manual is also suitable for

SP454

Download PDF

report

Mountfield HP45 Operating instructions

This manual is also suitable for

Mountfield HP45 Operating instructions

Related papers

Other documents