Mountfield ME330 Operating instructions

Mountfield
Brand
Mountfield
Model
ME330
Category
Lawnmowers
Type
Operating instructions
1
Please Read These Instructions
Before Using Your Mower
Operating Instructions
for models
ME330, ME370 Electric Lawnmowers
Product Codes:
297330068
297370068
Do not return this product to store, please call
the Service Link Helpline.
Visit www.servicelink.org.uk for a quick start video
Supported by
For all your Warranty,
Parts and Service needs
0800 121 6585
www.servicelink.org.uk
2
ENGLISH (Original instructions)
- Safety precautions .....................................................................................3
- Know your mower ......................................................................................4
- How to start mowing ..................................................................................6
- Maintenance .............................................................................................. 9
- Fault Finding ..............................................................................................9
GUARANTEE ............................................................................................11
EN
3
Thank you for purchasing a Mounteld lawnmower. This machine will give you many years of safe and
reliable service if operated in accordance with these instructions. Please read and understand these
operating instructions before using your mower. Failure to do so could result in personal injury
or damage to the equipment.
SAFETY PRECAUTIONS
Your lawnmower should be used with due care and attention. Symbols have therefore been placed on various parts of
the machine to remind you of the main precautions to be taken. Their meaning is explained below. You are also asked
to carefully read the safety regulations in the applicable chapter of this handbook
1. Warning: Read the instruction manual before using the machine.
2. Beware of thrown objects: Keep other people at a safe distance
whilst working.
3. Beware of cutting: Moving blades. Do not put hands or feet near
the blades. Disconnect from the mains supply before carrying out any
repairs or maintenance.
DESCRIPTION OF SYMBOLS ON CONTROLS (where applicable)
15. Grass catcher content indicator up (a) = empty / down (b) = full
Maximum noise and vibration levels
ME330 ME370
Acoustic pressure level
- Measurement uncertainty
dB(A)
dB(A)
75
3
76
3
Measured acoustic power level
- Measurement uncertainty
dB(A)
dB(A)
86
0,45
89,7
0,58
Guaranteed acoustic power level
dB(A) 87 91
Vibration level
- Measurement uncertainty
m/s
2
m/s
2
1,45
0,64
2,3
0,7
15
4
1. Sound power level
2. Conformity marking
3. Month / Year of manufacture
4. Type of machine
5. Serial number
6. Name and address of Manufacturer
7. Article code
8. Motor nominal power and maximum operating speed
9. Weight in kg
10. Power voltage and frequency
11. Electrical protection rating
As soon as you have purchased the machine, do not forget to write the identication numbers (3-4-5-7)in the spaces
on the last page of the manual.
KNOW YOUR MOWER
14
23
6
8
5 7
11
kW
10
9
Type:
- s/n
Hz
V
/min
Art.N.
Operator Presence Control
(OPC)
(Lever-upper)
Handle Securing
Knob
Cutter Deck
Grass Collector
Deflector Flap
5
The following safety precautions must be observed at all times. Please read them carefully.
TRAINING
1) Read the instructions carefully. Get familiar with the controls and proper use of the equipment. Learn how to
stop the motor quickly.
2) Only use the lawnmower for the purpose for which it was designed, i.e. for cutting and collecting grass.
Any other use can be hazardous, causing damage to the machine. Examples of improper use may include, but
are not limited to:
– transport of people, children or animals on the machine
– being transported by the machine
– using the machine to tow or push loads
– using the machine for leaf or debris collection
– using the machine to trim hedges, or for cutting vegetation other than grass
– use of the machine by more than one person
– using the blade on surfaces other than grass
3) Never allow children or people unfamiliar with these instructions to use the lawnmower. Local regulations may
restrict the age of the operator.
4) Never use the lawnmower:
– When people, especially children, or pets are nearby
– If the operator has taken medicine or substances that can aect his ability to react and concentrate
5) Remember that the operator or user is responsible for accidents or hazards occurring to other people or their
property.
PRELIMINARY OPERATIONS
1) Whilst mowing, always wear sturdy footwear and long trousers. Do not operate the lawnmower when barefoot or
wearing open sandals. Avoid wearing clothing that is loose tting or has hanging cords or ties.
2) Thoroughly inspect the entire work area and remove anything that could be thrown by the machine or damage
the cutting unit or motor (stones, branches, iron wire, bones, etc.).
3) Before use, always inspect generally and in particular to see that the blade, screws and cutting unit are not
worn or damaged. Replace damaged or worn blades and screws in their entirety to preserve balance. Replace
damaged or unreadable labels.
4) Before use check the supply and extension cord for signs of damage or ageing. If the cord becomes damaged
during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.
OPERATION
1) Mow only in daylight or good articial light.
2) Avoid mowing wet grass or when it is raining.
3) Make sure you have a steady foothold on slopes.
4) Never run, always walk; do not let the lawnmower pull you.
5) Always mow transversely on slopes and never up and down.
6) Be extremely carefully when changing directions on slopes.
7) Never mow on overly steep slopes.
8) Be extremely careful when pulling the lawnmower towards you.
9) Immobilise the blade if the lawnmower must be inclined for transport, when moving over surfaces other than grass
and when the lawnmower is transported from or to an area that must be cut.
10) Never operate the lawnmower with damaged guards or without the grass collector or discharge guards.
11) Start up the motor carefully according to the instructions, keeping feet away from the blade.
12) Do not incline the lawnmower when starting the motor, unless necessary for start up. In this event, do not incline
it more than is absolutely necessary and only lift the part that is far from the operator. Always ensure that both
hands are in the working position before lowering the lawnmower again.
13) Do not start the machine when standing in front of the discharge opening.
14) Never place your hands and feet near or under rotating parts. Keep away from the discharge opening.
15) Do not lift or transport the lawnmower when the motor is running.
16) Stop the machine and remove plug from the socket. Make sure that all moving parts have come to a complete
stop:
– when transporting the machine;
– whenever you leave the machine;
– before clearing blockages or unclogging the chute;
6
– before checking, cleaning or working on the machine;
– after striking a foreign object. Inspect the machine for damage and make repairs before restarting and
operating the machine;
If the machine starts to vibrate abnormally (check immediately):
– inspect for damage;
– replace or repair any damaged parts at a Mounteld authorised service dealer;
– check for and tighten any loose parts.
17) Stop the motor:
– whenever you remove or reattach the grass collector;
– whenever you adjust the cutting height.
18) When mowing, always keep a safe distance from the rotary blade, given by the length of the handle.
19) WARNING - If something breaks or an accident occurs during mowing, turn o the motor immediately and
move the machine away to prevent further damage; if an accident occurs with injuries or third parties are
injured, carry out the rst aid measures most suitable for the situation immediately and contact the medical
authorities for any necessary health care. Carefully remove any debris that might cause damage or harm to
persons or animals should it not be seen.
MAINTENANCE AND STORAGE
1) Keep all nuts and screws tight to be sure the machine is always in a safe working condition. Routine maintenance
is essential for safety and for maintaining a high performance level.
2) Check the discharge guards and the grass collector frequently for wear or deterioration.
3) Be careful during adjustment of the machine to prevent entrapment of the ngers between moving blades and
xed parts of the machine.
4) Always allow the machine to cool down before storing.
5) When servicing the blades be aware that, even though the power source is switched o, the blades can still be
moved.
6) For safety reasons, never use the machine when it has worn or damaged parts. Parts must be replaced and not
repaired. Use original spare parts. Parts that are not of the same quality can damage the equipment and impair
your safety.
7) To reduce re hazards, keep the lawnmower and in particular, the motor, free of grass, leaves, or excessive
grease. Never leave containers with cut grass inside a storage area.
TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled, raised, transported or tilted you must:
– wear strong working gloves.
– grasp the machine at the points that oer a safe grip, taking account of the weight and its distribution.
– use an appropriate number of people for the weight of the machine and the characteristics of the vehicle or the
place where it is to be placed or collected.
2) During transport, fasten the machine securely with ropes or chains.
HOW TO START MOWING
Carefully remove the mower from the carton and read these Operating Instructions. An Owner’s Manual for the
engine is also included. Please read this before starting the engine.
WARNING - Unpacking and completing the assembly should be done on a at and stable surface,
with enough space for handling the machine and its packaging, always making use of any suitable
equipment.
Disposal of the packaging should be done in accordance with the local regulations in force.
HANDLE ASSEMBLY
• Assemble the lower right (Fig.5.A) and left (Fig.5.B) parts of the handle onto the screws (Fig.5.C) protruding from
the chassis.
• Fasten the knobs (Fig.5.E) using the supplied nuts and bolts (Fig.5.D).
• Tighten the knobs until the plastic piece holding the screw in position snaps (Fig.5.F).
• Fasten the top of the handle (Fig.5.G) to the bottom parts using the knobs (Fig.5.H) and the supplied nuts
and bolts (Fig.5.I) as shown, using one of the two holes provided for adjusting the height of the handle to the
operator's stature.
• Fit the cable clamp (Fig.5.J) in the indicated position and clamp the cable (Fig.5.K) holding it in place along the
inside of the machine.
7
E
F
A
J
K
B
G
C E
D
I
H
GRASS COLLECTOR
• Fit the cloth base by fastening the plastic bars onto the frame (it may help to use a screwdriver as shown in the
drawing) and hook the handle in place (Figure 6).
• To t the grass collector onto the mower, lift the rear safety deector ap and hook the collector onto the pegs.
STARTING YOUR MOWER
Read and understand the Safety Precautions before using your mower.
• The motor is controlled by a dual-action switch to prevent accidental start ups. Press the button (A) and pull the
lever (B) for start up. The motor will automatically stop when the lever (B) is released (Figure 7).
B
A
• Whilst mowing, make sure the electric cable is always behind you and on the side of the lawn that has already
been cut. The appearance of the lawn will improve if you alternate cutting in both directions at the same height.
• When the grass collector is too full, grass collection is no longer ecient and the sound of the lawnmower
changes.
Figure 5
A
A
B
A
A
Figure 6
Figure 7
8
To remove and empty the grass collector,
– release the switch lever and wait for the blade to stop;
– lift the rear discharge guard, grasp the handle and remove the grass collector keeping it in a tilted position.
STOPPING YOUR MOWER (Figure 8)
• When nished mowing, release the lever (A).
• Disconnect the extension cable FIRST from the general socket (B) THEN from the side of the lawnmower switch
(C).
B
C
A
ADJUSTING THE HEIGHT OF CUT
Lower or raise the chassis to cut the grass at dierent heights.
Do this when the cutting blade is stationary.
To adjust the cutting height:
1. Tilt the machine on one side.
2. Use both hands to position the wheel axle in one of the grooves on the inside of the chassis.
3. The height must be the same for both axes.
Do not tilt the wheel axle during this operation, so that it slots simultaneously
into one of the grooves provided.
A.
Ground position: The cutting height is in the highest position (Fig.9.A).
B.
Intermediate position: The cutting height is in the intermediate position (Fig.9.B).
C.
High position: The cutting height is in the lowest position (Fig.9.C).
Figure 8
A
B
C
Figure 9
9
MAINTENANCE
BEFORE EACH USE
• Always ensure that the mower is in a safe working condition.
• Inspect the cutter blade for damage; check safety devices and guards; check that all nuts, bolts and screws are
secure.
• Always make sure the air intakes are free of debris.
CUTTER BLADE
Examine the cutter blade regularly for wear or damage.
• A slightly worn blade can be re-sharpened by your local authorised Mounteld service dealer.
• If the blade is damaged it should be replaced. Replacement blade kits are available from your local authorised
Mounteld service dealer.
If in doubt refer to your local authorised Mounteld service dealer, or telephone 0800 121 6585.
STORAGE
A little time spent on your mower after use will ensure many years of reliable mowing.
To access the underside of the cutter deck, ensure that the mower is disconnected from the mains supply. Lift the
front wheels by lowering the handle until it rests on the ground.
AFTER EACH USE
• Remove any grass pulp from the underside of the cutter deck using a non-metallic instrument such as a piece of
wood. Take care not to damage the paintwork.
• Examine the cutter blade for any damage. A damaged blade may upset the balance of your mower and cause
excessive vibration. If in doubt refer to your authorised Mounteld service dealer.
• Inspect the grass collector and clean it if necessary. If the mesh becomes clogged airow will be reduced and impair
grass collection.
STORAGE
When the machine is to be stored away:
• Wait for the motor to cool.
• Clean the machine thoroughly.
• Check the machine for any damage. If necessary, contact the authorised Mounteld service dealer.
Store the machine:
• In a dry place.
• Protected from inclement weather.
• Covered with a sheet where possible.
• In a place where children cannot get to it.
• Making sure that keys or tools used for maintenance are removed.
FAULT FINDING
PROBLEM PROBABLE CAUSE SOLUTION
The electric lawnmower doesn't work The machine has no power supply Check the electrical connection
The electric lawnmower trips the
power supply.
The mains socket amperage is
insucient
Connect the machine to a mains
socket with sucient amperage
Other electrical appliances are
being used
Do not connect other appliances to
the same mains socket at the same
time
The cut grass is not collected in the
grass collector
The cutting blade has collided with
a foreign object and received a
knock
Check for damage and contact
an authorised Mounteld service
dealer for the replacement of the
cutting blade if necessary
The inside of the chassis is dirty Clean the inside of the chassis to
ease the grass discharge towards
the grass collector
Irregular grass cutting
The cutting blade is not in good
condition
Contact an authorised Mounteld
service dealer for the sharpening
or replacement of the cutting blade
10
Excessive noise and/or vibration is
experienced whilst working
Damaged or loose parts Stop the machine and disconnect
the plug from the socket. Inspect for
damage. Check for and tighten any
loose parts. Have all checks, repair
work and replacements carried out
by an authorised Mounteld service
dealer
Cutting blade ttings are loose or
the cutting blade is damaged
Stop the machine and disconnect
the plug from the socket, Contact
an authorised Mounteld service
dealer for checks, replacements or
repairs
HELPLINE
0800 121 6585
or visit
www.servicelink.org.uk
This product is supported by Service
Link. If you have been unable to find the
information you require above please
call the Service Link helpline. Here you
will find 1-2-1 help and advice from
garden machinery repair specialists.
Service link
>
What is Service Link? Service Link is an aftersales help
and
advice helpline with a national network of garden
machinery
repair specialists.
>
How can we help you? Here at Service Link we can help with
all your trouble shooting, warranty, parts and service needs.
Call us and speak to one of our advisors and if required, visit
one
of our 450 centres across the UK and Ireland.
>
How can you contact us? If in the unlikely event that this
product does require our help please visit the Service Link
website at www.servicelink.org.uk or alternatively contact
the helpline on 0800 121 6585 in the UK or 1800806149 in ROI.
11
CERTIFICATE OF CONFORMITY
A certicate of conformity is enclosed with the documentation as separate document.
An EXAMPLE is here on the bottom.
doc_base r. 12 - wbh _0
DICHIARAZIONE CE DI CONFORMITÁ (Istruzioni Originali)
(Direttiva Macchine 2006/42/CE, Allegato II, parte A)
1. La Società: ST. S.p.A. – Via del Lavoro, 6 – 31033 Castelfranco Veneto (TV) – Italy
2. Dichiara sotto la propria responsabilità, che la macchina: Tosaerba con conducente a piedi / taglio erba
a) Tipo / Modello Base
EW 330
b) Mese/Anno di costruzione
c) Matricola
elettrico
3. É conforme alle specifiche delle direttive:
• MD: 2006/42/EC
e) Ente Certificatore: /
f) Esame CE del tipo: /
• OND: 2000/14/EC, ANNEX VI - 2005/88/EC
D. Lgs. 262/2002, ANNEX VI, proc. 1 (Italy)
e) Ente Certificatore: N°0494 - SLG Prüf- und Zertifizierungs GmbH
Burgstädter Straße 20
09232 Hartmannsdorf, Germany
• EMCD: 2014/30/EU
• RoHS 2: 2011/65/EU
4. Riferimento alle Norme armonizzate:
EN 60335-1:2012+A11:2014
EN 60335-2-77:2010
EN 50581:2012
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-11:2000
g) Livello di potenza sonora misurato
86
dB(A)
h) Livello di potenza sonora garantito
87
dB(A)
i) Ampiezza di taglio
33
cm
n) Persona autorizzata a costituire il FascicoloTecnico: ST. S.p.A.
Via del Lavoro, 6
31033 Castelfranco Veneto (TV) - Italia
o) Castelfranco V.to, 15.06.2018 Senior VP R&D & Engineering
Maurizio Tursini
171514095_1
FR (
Traduction de la notice originale)
Déclaration CE de Conformité
(Directive Machines 2006/42/CE, Annexe II, partie
A)
1. La Société
2. Déclare sous sa propre responsabilité que la
machine : Tondeuse à gazon à conducteur à
pied / coupe du gazon
a) Type / Modèle de Base
b) Mois / Année de construction
c) Série
d) Moteur: électrique
3. Est conforme aux prescriptions des
directives :
e) Organisme de certification
f) Examen CE du Type
4. Renvoi aux Normes harmonisées
g) Niveau de puissance sonore mesuré
h) Niveau de puissance sonore garanti
i) Largeur de coupe
n) Personne habilitée à établir le Dossier
Technique :
o) Lieu et Date
EN (
Translation of the original instruction)
EC Declaration of Conformity
(Machine Directive 2006/42/EC, Annex II, part A)
1. The Company
2. Herby declares under its own responsibility
that the machine: Pedestrian-controlled lawn
mower / grass cutting
a) Type / Base Model
b) Month / Year of manufacture
c) Serial number
d) Motor: electric
3. Conforms to directive specifications:
e) Certifying body
f) EC examination of Type
4. Reference to harmonised Standards
g) Sound power level measured
h) Sound power level guaranteed
i) Range of cut
n) Person authorised to create the Technical
Folder:
o) Place and Date
DE (
Übersetzung der Originalbetriebsanleitung
)
EG-Konformitätserklärung
(Maschinenrichtlinie 2006/42/EG, Anhang II, Teil
A)
1. Die Gesellschaft
2. Erklärt auf eigene Verantwortung, dass die
Maschine: Handgeführter Rasenmäher /
rasenschnitt
a) Typ / Basismodell
b) Monat / Baujahr
c) Seriennummer
d) Motor: elektrisch
3. Den Anforderungen der folgenden Richtlinien
entspricht:
e) Zertifizierungsstelle
f) EG-Baumusterprüfung
4. Bezugnahme auf die harmonisierten Normen
g) Gemessener Schallleistungspegel
h) Garantierter Schallleistungspegel
i) Schnittbreite
n) Zur Verfassung der technischen Unterlagen
befugte Person:
o) Ort und Datum
NL (
Vertaling van de o orspronkelijk e gebruiksaanw ijzing)
EG-verklaring van overeenstemming
(Richtlijn Machines 2006/42/CE, Bijlage II, deel A)
1. Het bedrijf
2. Verklaart onder zijn eigen
verantwoordelijkheid dat de machine: Lopend
bediende grasmaaier / grasmaaier
a) Type / Basismodel
b) Maand / Bouwjaar
c) Serienummer
d) Motor: elektrisch
3. Voldoet aan de specificaties van de
richtlijnen:
e) Certificatie-instituut
f) EG-onderzoek van het Type
4. Verwijzing naar de Geharmoniseerde normen
g) Gemeten niveau van geluidsvermogen
h) Gegarandeerd niveau van geluidsvermogen
i) Snijbreedte
n) Bevoegd persoon voor het opstellen van het
Technisch Dossier
o) Plaats en Datum
ES (
Traducción del Manual Original)
Declaración de Conformidad CE
(Directiva Máquinas 2006/42/CE, Anexo II, parte
A)
1. La Empresa
2. Declara bajo su propia responsabilidad que la
máquina: Cortadora de pasto con operador de
pie / corte hierba
a) Tipo / Modelo Base
b) Mes / Año de fabricación
c) Matrícula
d) Motor: eléctrico
3. Cumple con las especificaciones de las
directivas:
e) Ente certificador
f) Examen CE del Tipo
4. Referencia a las Normas armonizadas
g) Nivel de potencia sonora medido
h) Nivel de potencia sonora garantizado
i) Amplitud de corte
n) Persona autorizada a realizar el Manual
Técnico:
o) Lugar y Fecha
PT (
Tradução do manual original)
Declaração CE de Conformidade
(Diretiva de Máquinas 2006/42/CE, Anexo II,
parte A)
1. A Empresa
2. Declara sob a própria responsabilidade que a
máquina: Corta-relvas para operador apeado /
corte da relva
a) Tipo / Modelo Base
b) Mês / Ano de fabrico
c) Matrícula
d) Moto: eléctrico
3. É conforme às especificações das diretivas:
e) Órgão certificador
f) Exame CE do Tipo
4. Referência às Normas harmonizadas
g) Nível medido de potência sonora
h) Nível garantido de potência sonora
i) Amplitude de corte
n) Pessoa autorizada a elaborar o Caderno
Técnico
o) Local e Data
EL (
Μετάφραση του πρωτοτύπου των οδη γιών
χρήσης)
EK-Δήλωση συμμόρφωσης
(Οδηγία Μηχανών 2006/42/CE, Παράρτημα II,
μέρος A)
1. Η Εταιρία
2. Δηλώνει υπεύθυνα ότι η μηχανή:
Χλοοκοπτική μηχανή με όρθιο χειριστή / κοπή
της χλόης
a) Τύπος / Βασικό Μοντέλο
b) Μήνας / Έτος κατασκευής
c) Αριθμός μητρώου
d) Κινητήρας: ηλεκτρικό
3. Συμμορφώνεται με τις προδιαγραφές της
οδηγίας:
e) Οργανισμός πιστοποίησης
f) Εξέταση CE του Τύπου
4. Αναφορά στους Κανονισμούς εναρμόνισης
g) Στάθμη μέτρησης ακουστικής ισχύος
h) Στάθμη εγγυημένης ακουστικής ισχύος
i) Εύρος κοπής
n) Εξουσιοδοτημένο άτομο για την κατάρτιση
του Τεχνικού Φυλλαδίου:
o) Τόπος και Χρόνος
TR (
Orijinal Talimatların Tercümesi)
AT Uygunluk Beyanı
(2006/42/CE Makine Direktifi, Ek II, bölüm A)
1. Şirket
2. Şahsi sorumluluğu altında aşağıdaki
makinenin: Ayak kumandalı çim biçme makinesi
/ çim kesimi
a) Tip / Standart model
b) Üretimin Ay / yıl
c) Sicil numarası
d) Motor: elektrikli
3. Aşağıdaki direktiflerin özelliklerine uygun
olduğunu beyan etmektedir:
e) Sertifikalandıran kurum
f) ... Tipi CE incelemesi
4. Harmonize standartlara atıf
g) Ölçülen ses güç seviyesi
h) Garanti edilen ses güç seviyesi
i) Kesim genişliği
n) Teknik Dosyayı oluşturmaya yetkili kişi:
o) Yer ve Tarih
MK (
Превод на оригиналните упатства )
Декларација за усогласеност со ЕУ
(Директива за машини 2006/42/CE, Анекс II,
дел A)
1. Компанијата
2. изјавува со целосна лична одговорност
дека следната машина: Тревокосачка со
оператор на нозе / косење трева
а) Тип / основен модел
б) Месец / Година на производство
в) етикета
г) мотор: на струја
3. Усогласено со спецификациите според
директивите:
д) тело за сертификација
ѓ) тест СЕ за типот
4. Референци за усогласени нормативи
е) Акустички притисок
ж) измерено ниво на звучна моќност
з) Ниво на гарантирана звучна моќност
н) овластено лице за составување на
Техничката брошура
o) место и датум
Warranty
Congratulations on the purchase of your Mounteld lawnmower. This product has been manufactured to the
highest quality standards and is guaranteed for domestic use against faulty parts or manufacture for a period of
12 months. Please note that if the machine is used commercially the guarantee period is 90 days from the date
of purchase. If you experience any problem with your Mounteld lawnmower please call our technical helpline
on 0800 121 6585 and our operators will endeavour to solve your problem. In the event your problem cannot be
resolved over the phone the operator will refer you to one of our local authorised service dealers.
This warranty is subject to the following terms;
• This warranty is not transferable. An original proof of purchase will be required in the event of a claim.
• Please phone 0800 121 6585 to locate your nearest Mounteld service dealer or visit www.servicelink.
org.uk. Parts subject to fair wear and tear (for example wheels, cables, blade) are not covered under this
warranty .
• Delivery and collection of the machine is your responsibility and not covered under this warranty.
• The warranty does not cover any breakages or damage that are a result of the following; misuse,
alteration, improper assembly or adjustment, neglect or accident.
• Expenses and costs incurred from loss of utility will not be compensated.
• The warranty does not cover machines that are transported outside of the UK & Eire.
This warranty is in addition to and does not detract from your contractual rights under statute or common law.
EXAMPLE
12
On delivery of your new Mounteld mower, we suggest
that you complete the box to the right.
The information for your machine is on the serial
number label, which is xed on the cutter deck at the
base of the handles. You will be asked for these details
if you have any problems or require spare parts.
Please keep your receipt, proof of purchase will be
required in the event of a claim.
dB
L
WA
Type:
................................
.................. -s/n .......................... -Art.N ..............................
STIGA LTD
Unit 8, Bluewater Estate, Bell Close, Plympton, Plymouth, Devon, PL7 4JH, England.
Manufactured by ST. S.p.A. Via del Lavoro, 6 I-31033 Castelfranco Veneto (TV) Italy
Part Number 171506300/0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Mountfield ME330 Operating instructions

Mountfield
Brand
Mountfield
Model
ME330
Category
Lawnmowers
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents