Vestil OLA-4-42-DLX Owner's manual

Brand: Vestil

Model: OLA-4-42-DLX

Type: Owner's manual

This manual is also suitable for

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

OLA-4-42; OLA-4-36-DLX; OLA-4-42-DLX

Instruction Manual

Receiving Instructions

After delivery, remove the packaging from the product. Inspect the product closely to determine whether it sustained

damage during transport. If damage is discovered, record a complete description of it on the bill of lading. If the

product is undamaged, discard the packaging.

NOTE: The end-user is solely responsible for confirming that product design, use, and maintenance comply with laws,

regulations, codes, and mandatory standards applied where the product is used.

Technical Service & Replacement Parts

For answers to questions not addressed in these instructions and to order replacement parts, labels, and

accessories, call our Technical Service and Parts Department at (260) 665-7586. The department can also be

contacted online at http://www.vestilmfg.com/parts_info.htm

Electronic copies of Instruction Manuals

Additional copies of this instruction manual may be downloaded from https://www.vestil.com/page-manuals.php

Vestil Manufacturing Corp.

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703

Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868

Fax: (260) 665-1339

Web: www.vestilmfg.com e-mail: info@vestil.com

Table of Contents

Page

Signal Words…………….………………………………….……………………………………….………..

Safety Instructions……………………………………………………………..……………….……….……

OLA-4-36/42-DLX Exploded View, Bill of Materials, & Specifications……………………………….....

OLA-4-42 exploded View, Bill of Materials, & Specifications..…………………………………………..

National Standards……………………………………………………………………………………….…..

Using the Lifter..…………………………………………………….…………………………………….….

5 - 6

Record of Satisfactory Condition…………………………………………………………………………...

Load Tests…………………………………………………………………………………………………….

Inspections and Maintenance…………………………………………………………………………........

Labeling Diagram.…………..…………………………………………....................................................

Limited Warranty…………………………………………….……………………………………………….

OLA-4-36/42-DLX OLA-4-42

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

SIGNAL WORDS

This manual uses SIGNAL WORDS to direct the reader’s attention to important safety-related messages.

These messages describe uses of the product that could result in personal injury or property damage. Each

signal word corresponds to a specific hazard level.

Identifies a hazardous situation which, if not avoided, WILL result in DEATH or

SERIOUS INJURY. Use of this signal word is limited to the most extreme situations.

Identifies a hazardous situation which, if not avoided, COULD result in DEATH or

SERIOUS INJURY.

Identifies practices likely to result in product/property damage, such as operation that might

damage the product.

SAFETY INSTRUCTIONS

Vestil strives to identify all foreseeable hazards associated with the use of its products. However, material

handling is dangerous and no manual can address every conceivable risk. Ultimately, the most effective way

to prevent injury is to apply sound judgment whenever using this device.

Improper or careless use of this product could result in death or serious personal injuries.

• Read and understand the entire manual before using, inspecting, or servicing the cylinder caddy.

DO NOT use this device until you read and understand the entire instruction manual. Read the manual to

refresh your understanding of proper use and maintenance procedures.

• DO NOT exceed the rated load/capacity of your lifter. Capacity figures are provided on product labeling.

See Label 320 in LABELING DIAGRAM on p. 7.

• Only use the lifter in accordance with the instructions in this manual, applicable provisions of ASME

B30.20 Below-the-Hook (BTH) Lifting Devices, and all laws, regulations, codes, etc. that apply to BTH

devices.

• DO NOT elevate the lifter if the hoist rope/chain is kinked. Make sure that multiple part lines are not

twisted around each other before elevating the lifter.

• Center and evenly distribute the load on its pallet before engaging the pallet with the lifter. The load must

not overhang any side of its pallet.

• Adjust the position of the lifting bale to balance the lifter before elevating it. The forks of the lifter must be

horizontal when the lifter (and load) are elevated/suspended. If a load cannot be balanced, do not use the

lifter to elevate it. Select another lifting device.

• DO NOT modify the product in any way UNLESS you first obtain written approval from Vestil. Unapproved

modifications automatically void the LIMITED WARRANTY (p. 8) and might make the product unsafe to use.

• Avoid load (and lifter) swinging by making sure the hoist rope/chain is vertical before elevating the load.

• Slowly and carefully raise, lower, and move the lifter when it is loaded and when it is not loaded. DO NOT

start or stop suddenly. Sudden change could cause the load to slide on the forks.

• DO NOT contact any obstructions with either the load or the lifter. Make sure the path of travel is clear

before elevating and moving the lifter.

• NEVER lift people or carry loads over people.

• SO NOT use the lifter for side pulls or for sliding the load.

• DO NOT climb on the lifter or ride on it or the load. DO NOT allow others to climb, or ride, on the lifter or

on the load.

• DO NOT leave the lifter unattended while it is elevated. Land the load and store the lifter before leaving it.

• Guide the lifter by grasping both operator handles. Keep clear of the lifter while moving it. In particular,

keep feet out from underneath the lifter at all times. Make sure that clothing cannot become entangled in the

load or with the lifter.

• DO NOT remove or deface labels applied to the unit. DO NOT use this device UNLESS each label is in

place, undamaged, and easily readable from a reasonable distance. See LABELING DIAGRAM on p. 8.

• Inspect the product as instructed in INSPECTIONS AND MAINTENANCE on p. 7.

• DO NOT use this lifter if it is damaged, malfunctioning, or missing parts.

• DO NOT elevate the lifter any higher than necessary to move it. Keep it as close to the ground as

possible.

• DO NOT use the lifter if it is tagged “Out of service” or is otherwise designated as malfunctioning.

WARNING

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

OLA-4-36/42-DLX EXPLODED VIEW AND BILL OF MATERIALS

38-006-033

ITEM PART NO. DESCRIPTION QTY.

38-514-056

WELDMENT, TUBE, INNER

FRAME

38-514-058

WELDMENT, TUBE, CENTER

ASSEMBLY

99-112-057 PIN, HEIGHT ADJUSTMENT 1

38-514-059 WELDMENT, HOOK BAIL 1

38-028-007

38-028-015

FORK

OLA-4-36-DLX

OLA-4-42-DLX

38-112-023 PIN, BALE 1

33424

MACHINE BUSHING, LOW

CARBON, PLAIN FINISH, Ø3/4"

X 18 GA

68015

EXTERNAL RETAINING

RING,PHOSPHATE, 3/4"

11209

1/2-13 X 1 1/2" LG HHCS -

ASTM A307 GRADE A, ZINC

PLATED

36110 HEX NUT Z-PLATED, Ø 1/2 - 13 4

SPECIFICATIONS

Documents that provide specifications for OLA-#-##-DLX are available online to anyone who visits Vestil’s

website. Specifications include dimensions, net weight, and capacity information. To access the appropriate

specifications document, navigate to this webpage: https://www.vestil.com/product.php?FID=575

Click the

“Specifications” tab. Scroll the page to the entry for the model ladder you purchased, and click the button in the

“PDF” column that looks like a pencil inside a blue-bordered box. A PDF file will open. This file is the specifications

document. Print a copy of the document and keep it with your copy of this manual. This is an exemplar

specifications document for model OLA-4-42-DLX:

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

SPECIFICATIONS

Documents that provide specifications for OLA-#-42 model lifters

are available online to anyone who visits Vestil’s

website. Specifications include dimensions, net weight, and capacity information.

To access the appropriate

specifications document, navigate to this webpage: https://www.vestil.com/product.php?FID=575.

Click the

“Specifications” tab. Scroll the page to the entry for the model ladder you purchased, and click the button in the

“PDF” column that looks like a pencil inside a blue-bordered box. A PDF file will open. This file is the specifications

document. Print a copy of the document and keep it with your copy of this manual. This is an exemplar specification

document for model OLA-4-42.

OLA-4-42 EXPLODED VIEW AND BILL OF MATERIALS

38-006-031

ITEM PART NO. DESCRIPTION QTY.

38-514-003

WELDMENT, INNER

FRAME HOIST TUBE

38-516-003

BRACKET, SPRING

BALANCE SUB-SSEMBLY

38-528-001 FORK, SUB-ASSEMBLY 2

38-514-004

WELDMENT, FRAME

BASE SUB-ASSEMBLY

99-112-057

PIN, HEIGHT

ADJUSTMENT

38-112-002 PIN, BALE ADJUSTMENT 1

13154 BOLT,7/16"-14UNC x 7/8" 2

36108

HEX NUT Z PLATED,

Ø7/16-14

38-117-001

RETAINER RING,

EXTERNAL FOR Ø3/4

SHAFT

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

NATIONAL STANDARDS

OLA-series products are Below-the-Hook lifting (BTH) devices designed to facilitate handling of palletized

loads. American National Standard ASME B30.20 (the “Standard”), which can be purchased online at

https://www.asme.org/codes-standards/find-codes-standards/b30-20-hook-lifting-devices

) provides

inspection, testing, maintenance, and operation instructions for users of BTH devices. Acquire a copy of the

Standard. Apply all mandatory provisions of Chapter 20-1: Structural and Mechanical Lifting Devices.

Contact local occupational safety and health specialists to determine whether there are laws, ordinances,

codes, etc. (“authorities”) in addition to the Standard that apply to BTH pallet handlers in the location where

the handler will be used. If content in this manual conflicts with provisions in authorities or the Standard,

apply the provisions from the authorities or Standard. Contact

TECHNICAL SERVICE to report conflicts.

USING THE LIFTER

This lifter is a below-the-hook lifting device, design category B (used for loads and variations which are

severe and not accurately defined), service class 1 (20,001 to 100,000 load cycles). It should only be

operated by qualified personnel. ASME B30.20 defines qualified person as “a person who, by the

possession of a recognized degree in an applicable field or certificate of professional standing, or who, by

extensive knowledge, training, and experience, has successfully demonstrated the ability to solve or resolve

problems relating to the subject matter at hand.” Qualified persons include designated persons, trainees

under the direct supervision of a designated person, maintenance personnel, test personnel, and inspectors.

ADJUSTING THE LIFTER

Height and width of OLA-series lifters are adjustable.

• Height adjustments: Remove the height adjustment pin (99-112-057). Pull the inner frame tube up. Align

the pin holes in the inner and outer frame tubes; then reinstall the height adjustment pin.

• Width adjustments: Each fork is independently adjustable.

o OLA-4-42: Pull up on the detent pin and turn the top of the pin 90° to hold it in the raised position.

Slide the fork along the frame. Lock the fork in the new position by releasing the detent pin. Adjust

the position of the fork by sliding it along the frame until the detent pin seats into the nearest pin hole

in the frame. The forks must be the same distance from the centerline

o OLA-4-36-DLX & OLA-4-42-DLX: Slide the forks along the lifter carriage. Position the forks the same

distance away from the outer tube of the frame.

LOADING THE LIFTER

ONLY lift pallets (closed bottom skids) with this device. Make sure that loads are centered and evenly

distributed on their pallets. Make sure that loads are securely bound to their pallets before lifting them. If

loose items fall off of the pallet while the lift is underway, people could be injured. The center of gravity of the

load also changes if load items fall off of a pallet. Shifting center of gravity could cause the lifter to tip and

the rest of the load could be lost.

1. Attach the hoist hook to the connection

link (OLA-4-42) or bale (OLA-4-36/42-

DLX).

2. Stand behind the lifter. Grasp both

operator handles. Fully insert the forks

into the fork channels of the pallet.

3. Slowly raise the lifter. Check load

balance and stability. The forks should be

level front-to-back and side-to-side. If the

lifter tilts forward or backward, the

position of the lifting bale must be

adjusted.

a. OLA-4-42: Remove the bale

adjustment pin. Slide the bale along

the lifting arm. Reinstall the pin.

i. Lifter tilts forward (fork tips down):

Shift the bale towards the free end

of the lifting arm.

ii. Lifter tilts backward: Shift the bale

towards the back of the lifting arm.

OLA-4-42

C. Detent

B. Height

adjustment pin

A. Bale

adjustment

Front of

lifting arm

Bale

Fork

Operator

handle

Connection

link

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

b. OLA-4-36-DLX & OLA-4-42-DLX: slide

the bale along the lifting arm and seat

the bale pin into one of the pin slots in

the underside of the lifting arm.

i. Lifter tilts forward (fork tips down):

Shift bale mechanism towards the

free end of the lifting arm.

ii. Lifter tilts backwards (fork tips up):

Shift bale towards the back of the

lifting arm.

4. Minimize swinging! Make sure that the

hoist is centered above the bale, i.e. hoist

chain/rope is vertical. If the hoist

chain/rope is not vertical, the lifter will

swing as it is elevated.

5. Slowly raise the lifter. Watch the device as

it elevates. If the lifter begins to tilt

forwards or backwards, return the lifter to

the ground and adjust bale position as

described in step 3. Raise the lifter again

to determine whether it is balanced. If

balance has been achieved, proceed to

the next step. Otherwise, try again to

balance the lifter. If the lifter cannot be

balanced, use another lifting device to

handle the load.

6. Stand behind the lifter. Grasp both operator handles and gradually begin pushing the lifter in the

necessary direction. Avoid sudden starts and stops.

7. Lower the lifter onto even, level ground. Make sure that the pallet and load are stable and entirely

supported by the ground.

8. Raise the lifter just enough to carefully withdraw the forks from the pallet. Before leaving the lifter,

lower it to the ground and disconnect the hoist chain/rope from the bale.

RECORD OF SATISFACTORY CONDITION (THE “RECORD”)

Record the condition of the lifter before putting it into regular service. Thoroughly photograph the unit

from multiple angles. Include close range photos of all labeling, the forks, bale loops and pins, width

adjustment pins, height adjustment pins, and all welds. Measure the length and width of the bale

opening. Record your measurements. Write a description of the overall condition of the lifter. Collate

the photographs and writings into a single file. Mark the file appropriately to identify it. The file is a

record of the lifter in satisfactory condition. Compare the results of all inspections to this RECORD to

determine whether the unit is in satisfactory condition. If the lifter is not in satisfactory condition, repair it

before returning it to service. Purely cosmetic changes, like damaged paint/powdercoat, do not

constitute changes from satisfactory condition. However, touchup paint should be applied to all affected

areas as soon as cosmetic damage occurs to prevent rusting and corrosion. If left unaddressed,

rust/corrosion will degrade the condition of the lifter and could make it unsafe to use.

LOAD TESTS

After creating a RECORD OF SATISFACTORY CONDITION and before using the lifter for the first

time, a qualified person should conduct a load test. The test load should be 125% of the rated load, i.e.

4000lb.x1.25 = 5000lb. (2272.7kg). Elevate the lifter a few inches above the ground. After a couple

minutes, return it to the ground and unload it. Perform a Monthly Inspection as described in

INSPECTIONS AND MAINTENANCE on p. 7. The (qualified) person performing the test must compose

a written report confirming the load rating of the lifter. The load rating should not be more than 80% of

the test load. The lifter must undergo load testing whenever it is repaired. Never modify the lifter without

first obtaining written approval from Vestil.

OLA-4-36/42-DLX

Bale pin

Bale

loop

Height adjustment pin

Front of

lifting arm

Fork

Operator

handle

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

INSPECTIONS AND MAINTENANCE

Regular inspections and maintenance are essential. Always inspect and maintain this product

in accordance with the instructions in this manual.

Inspections and repairs should be performed by qualified persons. Compare the results of each

inspection to the RECORD OF SATISFACTORY CONDITION. Do not use the lifter unless all parts are in

satisfactory condition. Replace parts that are not in satisfactory condition before returning the lifter to

service. Only use manufacturer-approved replacement parts to restore the unit to satisfactory condition.

DON’T GUESS! If you have any questions about the condition of your lifter, contact the TECHNICAL

SERVICE

department. The phone number is provided on the cover page of this manual. Never make

temporary repairs of damaged or missing parts.

Every lift – The operator must inspect the lifter before every lift. Closely inspect the bale mechanisms.

Check the bale loop and bale pin for cracks, elongation, warps, and other forms of damage. Confirm that the

bale mechanism is securely pinned in place. Remove debris from the surfaces of the forks.

Monthly Inspections – At least once per month a qualified person must perform the following

inspections. Written reports should be prepared for every monthly inspection including inspections following

LOAD TESTS.

1. Frame elements: Examine all frame elements (inner frame tube; outer frame tube; fork carriage) for

deformation, cracks, severe wear, corrosion/rusting, and metal fatigue. If rusting is purely superficial,

remove it with a steel bristle brush or steel wool. Clean the affected area and apply touchup paint. If

rusting, rot, or thinning has weakened the material, contact TECHNICAL SERVICE for advice.

2. Pins and fasteners: Examine all pins (bale pin; height adjustment pin; width adjustment pins). Pins

should be straight. Examine retaining clips used to secure pins in place. Confirm that both detent pins

(OLA-4-42) retract automatically.

3. Bale assemblies: Measure the length and width of the bale openings. Make sure the measurements

match the measurements in the RECORD.

4. Forks: Thoroughly examine both forks. Look for cracks and severe wear. Confirm that each fork attaches

normally to the carriage.

5. Snap hooks and chains: Examine the chains and snap hooks. Hooks should not be bent, cracked,

twisted, or otherwise deformed. Latches should automatically close. Chain links should not be damaged,

e.g. bent, cracked, or stretched.

6. Labels: Check all labels. Labels are shown in the LABELING DIAGRAM (below). Replace labels that are

missing, damaged, or not easily readable.

LABELING DIAGRAM

Label content and location are subject to change so your product might not be labeled exactly as shown.

Compare the diagram below with the RECORD. If you have any questions about labeling, contact

TECHNICAL SERVICE. Replace all labels that are damaged, missing, or not easily readable (e.g. faded).

To order replacement labels, contact the technical service and parts department online at

http://www.vestilmfg.com/parts_info.htm

. Alternatively, request replacement parts and/or service by calling

(260) 665-7586 and asking the operator to connect you to TECHNICAL SERVICE.

A: Label 991 B: Label 675

C: Label 531 D: Label 320

Table of Contents Rev. 11/10/2020 OLA-4 MANUAL

LIMITED WARRANTY

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and

workmanship during the warranty period. Our warranty obligation is to provide a replacement for a defective,

original part covered by the warranty after we receive a proper request from the Warrantee (you) for warranty

service.

Who may request service?

Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an

authorized distributor AND Vestil has been fully paid.

Definition of “original part”?

An original part is a part used to make the product as shipped to the Warrantee.

What is a “proper request”?

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays

the shipping date; AND 2) a written request for warranty service including your name and phone number. Send

requests by one of the following methods:

US Mail Fax Email

Vestil Manufacturing Corporation (260) 665-1339 info@vestil.com

2999 North Wayne Street, PO Box 507 Phone Enter “Warranty service request”

Angola, IN 46703 (260) 665-7586 in subject field.

In the written request, list the parts believed to be defective and include the address where replacements should be

delivered. After Vestil receives your request for warranty service, an authorized representative will contact you to

determine whether your claim is covered by the warranty. Before providing warranty service, Vestil will require you

to send the entire product, or just the defective part (or parts), to its facility in Angola, IN.

What is covered under the warranty?

The warranty covers defects in the following original, dynamic parts: motors, hydraulic pumps, motor controllers,

and cylinders. It also covers defects in original parts that wear under normal usage conditions (“wearing parts”),

such as bearings, hoses, wheels, seals, brushes, and batteries.

How long is the warranty period?

The warranty period for original dynamic components is 90 days. For wearing parts, the warranty period is 90

days. Both warranty periods begin on the date Vestil ships the product to the Warrantee. If the product was

purchased from an authorized distributor, the periods begin when the distributor ships the product. Vestil may, at

its sole discretion, extend a warranty period for products shipped from authorized distributors by up to 30 days to

account for shipping time.

If a defective part is covered by the warranty, what will Vestil do to correct the problem?

Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will

contact you to discuss your claim.

What is not covered by the warranty?

The Warrantee (you) are responsible for paying labor costs and freight costs to return the product to Vestil for

warranty service.

Events that automatically void this Limited Warranty.

• Misuse;

• Negligent assembly, installation, operation or repair;

• Installation/use in corrosive environments;

• Inadequate or improper maintenance;

• Damage sustained during shipping;

• Collisions or other accidents that damage the product;

• Unauthorized modifications: Do not modify the product IN ANY WAY without first receiving written authorization

from Vestil.

Do any other warranties apply to the product?

Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the

extent allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.

Vestil makes no warranty or representation that this product complies with any state or local design, performance,

or safety code or standard. Noncompliance with any such code or standard is not a defect in material or

workmanship.

Vestil OLA-4-42-DLX Owner's manual

Brand: Vestil

Model: OLA-4-42-DLX

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Vestil OLA-4-42-DLX Owner's manual

This manual is also suitable for

Vestil OLA-4-42-DLX Owner's manual

Related papers

Other documents